[PATCH v6 net-next 03/10] net: phy: Add support for LAN937x T1 phy driver
From: Prasanna Vengateshan
Date: Fri Oct 29 2021 - 01:23:58 EST
Added support for Microchip LAN937x T1 phy driver. The sequence of
initialization is used commonly for both LAN87xx and LAN937x
drivers. The new initialization sequence is an improvement to
existing LAN87xx and it is shared with LAN937x.
Also relevant comments are added in the existing code and existing
soft-reset customized code has been replaced with
genphy_soft_reset().
access_ereg_clr_poll_timeout() API is introduced for polling phy
bank write and this is linked with PHYACC_ATTR_MODE_POLL.
Finally introduced function table for LAN937X_T1_PHY_ID along with
microchip_t1_phy_driver struct.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@xxxxxxxxxxxxx>
---
drivers/net/phy/microchip_t1.c | 345 ++++++++++++++++++++++++++-------
1 file changed, 276 insertions(+), 69 deletions(-)
diff --git a/drivers/net/phy/microchip_t1.c b/drivers/net/phy/microchip_t1.c
index a4de3d2081c5..c933a9d3233d 100644
--- a/drivers/net/phy/microchip_t1.c
+++ b/drivers/net/phy/microchip_t1.c
@@ -32,6 +32,7 @@
#define PHYACC_ATTR_MODE_READ 0
#define PHYACC_ATTR_MODE_WRITE 1
#define PHYACC_ATTR_MODE_MODIFY 2
+#define PHYACC_ATTR_MODE_POLL 3
#define PHYACC_ATTR_BANK_SMI 0
#define PHYACC_ATTR_BANK_MISC 1
@@ -45,8 +46,50 @@
#define LAN87XX_CABLE_TEST_OPEN 1
#define LAN87XX_CABLE_TEST_SAME_SHORT 2
+#define T1_M_CTRL_REG 0x09
+#define T1_M_CFG BIT(11)
+
+#define T1_MODE_STAT_REG 0x11
+#define T1_DSCR_LOCK_STATUS_MSK BIT(3)
+#define T1_LINK_UP_MSK BIT(0)
+
+#define T1_REG_BANK_SEL_MASK 0x7
+#define T1_REG_BANK_SEL 8
+#define T1_REG_ADDR_MASK 0xFF
+
+#define T1_M_STATUS_REG 0x0A
+#define T1_LOCAL_RX_OK BIT(13)
+#define T1_REMOTE_RX_OK BIT(12)
+
+#define LAN87XX_PHY_ID 0x0007c150
+#define LAN937X_T1_PHY_ID 0x0007c181
+#define LAN87XX_PHY_ID_MASK 0xfffffff0
+#define LAN937X_PHY_ID_MASK 0xfffffff0
+
+/* T1 Registers */
+#define T1_AFE_PORT_CFG1_REG 0x0B
+#define T1_POWER_DOWN_CONTROL_REG 0x1A
+#define T1_SLV_FD_MULT_CFG_REG 0x18
+#define T1_CDR_CFG_PRE_LOCK_REG 0x05
+#define T1_CDR_CFG_POST_LOCK_REG 0x06
+#define T1_LCK_STG2_MUFACT_CFG_REG 0x1A
+#define T1_LCK_STG3_MUFACT_CFG_REG 0x1B
+#define T1_POST_LCK_MUFACT_CFG_REG 0x1C
+#define T1_TX_RX_FIFO_CFG_REG 0x02
+#define T1_TX_LPF_FIR_CFG_REG 0x55
+#define T1_SQI_CONFIG_REG 0x2E
+#define T1_MDIO_CONTROL2_REG 0x10
+#define T1_INTERRUPT_SOURCE_REG 0x18
+#define T1_INTERRUPT2_SOURCE_REG 0x08
+#define T1_EQ_FD_STG1_FRZ_CFG 0x69
+#define T1_EQ_FD_STG2_FRZ_CFG 0x6A
+#define T1_EQ_FD_STG3_FRZ_CFG 0x6B
+#define T1_EQ_FD_STG4_FRZ_CFG 0x6C
+#define T1_EQ_WT_FD_LCK_FRZ_CFG 0x6D
+#define T1_PST_EQ_LCK_STG1_FRZ_CFG 0x6E
+
#define DRIVER_AUTHOR "Nisar Sayed <nisar.sayed@xxxxxxxxxxxxx>"
-#define DRIVER_DESC "Microchip LAN87XX T1 PHY driver"
+#define DRIVER_DESC "Microchip LAN87XX/LAN937X T1 PHY driver"
struct access_ereg_val {
u8 mode;
@@ -59,12 +102,16 @@ struct access_ereg_val {
static int access_ereg(struct phy_device *phydev, u8 mode, u8 bank,
u8 offset, u16 val)
{
+ u8 prev_bank;
u16 ereg = 0;
int rc = 0;
+ u16 t;
+ /* return if mode and bank are invalid */
if (mode > PHYACC_ATTR_MODE_WRITE || bank > PHYACC_ATTR_BANK_MAX)
return -EINVAL;
+ /* if the bank is SMI, then call phy_read() & phy_write() directly */
if (bank == PHYACC_ATTR_BANK_SMI) {
if (mode == PHYACC_ATTR_MODE_WRITE)
rc = phy_write(phydev, offset, val);
@@ -74,16 +121,43 @@ static int access_ereg(struct phy_device *phydev, u8 mode, u8 bank,
}
if (mode == PHYACC_ATTR_MODE_WRITE) {
+ /* Initialize to Write Mode */
ereg = LAN87XX_EXT_REG_CTL_WR_CTL;
+
+ /* Write the data to be written in to the Bank */
rc = phy_write(phydev, LAN87XX_EXT_REG_WR_DATA, val);
if (rc < 0)
return rc;
} else {
+ /* Initialize to Read Mode */
ereg = LAN87XX_EXT_REG_CTL_RD_CTL;
}
ereg |= (bank << 8) | offset;
+ /* DSP bank access workaround for lan937x */
+ if (phydev->phy_id == LAN937X_T1_PHY_ID) {
+ /* Read previous selected bank */
+ rc = phy_read(phydev, LAN87XX_EXT_REG_CTL);
+ if (rc < 0)
+ return rc;
+
+ /* store the prev_bank */
+ prev_bank = (rc >> T1_REG_BANK_SEL) & T1_REG_BANK_SEL_MASK;
+
+ if (bank != prev_bank && bank == PHYACC_ATTR_BANK_DSP) {
+ t = ereg & ~T1_REG_ADDR_MASK;
+
+ t &= ~LAN87XX_EXT_REG_CTL_WR_CTL;
+ t |= LAN87XX_EXT_REG_CTL_RD_CTL;
+
+ /* access twice for DSP bank change,dummy access */
+ rc = phy_write(phydev, LAN87XX_EXT_REG_CTL, t);
+ if (rc < 0)
+ return rc;
+ }
+ }
+
rc = phy_write(phydev, LAN87XX_EXT_REG_CTL, ereg);
if (rc < 0)
return rc;
@@ -112,71 +186,166 @@ static int access_ereg_modify_changed(struct phy_device *phydev,
return rc;
}
+static int access_ereg_clr_poll_timeout(struct phy_device *phydev, u8 bank,
+ u8 offset, u16 mask, u16 clr)
+{
+ int val;
+
+ if (bank != PHYACC_ATTR_BANK_SMI)
+ return -EINVAL;
+
+ return phy_read_poll_timeout(phydev, offset, val, (val & mask) == clr,
+ 150, 30000, true);
+}
+
static int lan87xx_phy_init(struct phy_device *phydev)
{
static const struct access_ereg_val init[] = {
- /* TX Amplitude = 5 */
- {PHYACC_ATTR_MODE_MODIFY, PHYACC_ATTR_BANK_AFE, 0x0B,
- 0x000A, 0x001E},
- /* Clear SMI interrupts */
- {PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_SMI, 0x18,
- 0, 0},
- /* Clear MISC interrupts */
- {PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_MISC, 0x08,
- 0, 0},
- /* Turn on TC10 Ring Oscillator (ROSC) */
- {PHYACC_ATTR_MODE_MODIFY, PHYACC_ATTR_BANK_MISC, 0x20,
- 0x0020, 0x0020},
- /* WUR Detect Length to 1.2uS, LPC Detect Length to 1.09uS */
- {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_PCS, 0x20,
- 0x283C, 0},
- /* Wake_In Debounce Length to 39uS, Wake_Out Length to 79uS */
- {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_MISC, 0x21,
- 0x274F, 0},
- /* Enable Auto Wake Forward to Wake_Out, ROSC on, Sleep,
- * and Wake_In to wake PHY
- */
- {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_MISC, 0x20,
- 0x80A7, 0},
- /* Enable WUP Auto Fwd, Enable Wake on MDI, Wakeup Debouncer
- * to 128 uS
- */
- {PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_MISC, 0x24,
- 0xF110, 0},
- /* Enable HW Init */
- {PHYACC_ATTR_MODE_MODIFY, PHYACC_ATTR_BANK_SMI, 0x1A,
- 0x0100, 0x0100},
+ /* TXPD/TXAMP6 Configs */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_AFE,
+ T1_AFE_PORT_CFG1_REG, 0x002D, 0 },
+ /* HW_Init Hi and Force_ED */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI,
+ T1_POWER_DOWN_CONTROL_REG, 0x0308, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_EQ_FD_STG1_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_EQ_FD_STG2_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_EQ_FD_STG3_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_EQ_FD_STG4_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_EQ_WT_FD_LCK_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_PST_EQ_LCK_STG1_FRZ_CFG, 0x0002, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_SLV_FD_MULT_CFG_REG, 0x0D53, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_CDR_CFG_PRE_LOCK_REG, 0x0AB2, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_CDR_CFG_POST_LOCK_REG, 0x0AB3, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_LCK_STG2_MUFACT_CFG_REG, 0x0AEA, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_LCK_STG3_MUFACT_CFG_REG, 0x0AEB, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_POST_LCK_MUFACT_CFG_REG, 0x0AEB, 0 },
+ /* Pointer delay */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_RX_FIFO_CFG_REG, 0x1C00, 0 },
+ /* Tx iir edits */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1000, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1861, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1061, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1922, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1122, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1983, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1183, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1944, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1144, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x18c5, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x10c5, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1846, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1046, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1807, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1007, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1808, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1008, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1809, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1009, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180A, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100A, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180B, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100B, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180C, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100C, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180D, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100D, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180E, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100E, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x180F, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x100F, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1810, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1010, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1811, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1011, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_TX_LPF_FIR_CFG_REG, 0x1000, 0 },
+ /* SQI enable */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_DSP,
+ T1_SQI_CONFIG_REG, 0x9572, 0 },
+ /* Flag LPS and WUR as idle errors */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI,
+ T1_MDIO_CONTROL2_REG, 0x0014, 0 },
+ /* Restore state machines without clearing registers */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI,
+ T1_POWER_DOWN_CONTROL_REG, 0x0200, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI,
+ T1_MDIO_CONTROL2_REG, 0x0094, 0 },
+ { PHYACC_ATTR_MODE_POLL, PHYACC_ATTR_BANK_SMI,
+ T1_MDIO_CONTROL2_REG, 0x0080, 0 },
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_AFE,
+ T1_AFE_PORT_CFG1_REG, 0x000C, 0 },
+ /* Read INTERRUPT_SOURCE Register */
+ { PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_SMI,
+ T1_INTERRUPT_SOURCE_REG, 0, 0 },
+ /* Read INTERRUPT_SOURCE Register */
+ { PHYACC_ATTR_MODE_READ, PHYACC_ATTR_BANK_MISC,
+ T1_INTERRUPT2_SOURCE_REG, 0, 0 },
+ /* HW_Init Hi */
+ { PHYACC_ATTR_MODE_WRITE, PHYACC_ATTR_BANK_SMI,
+ T1_POWER_DOWN_CONTROL_REG, 0x0300, 0 },
};
int rc, i;
- /* Start manual initialization procedures in Managed Mode */
- rc = access_ereg_modify_changed(phydev, PHYACC_ATTR_BANK_SMI,
- 0x1a, 0x0000, 0x0100);
- if (rc < 0)
- return rc;
-
- /* Soft Reset the SMI block */
- rc = access_ereg_modify_changed(phydev, PHYACC_ATTR_BANK_SMI,
- 0x00, 0x8000, 0x8000);
- if (rc < 0)
- return rc;
-
- /* Check to see if the self-clearing bit is cleared */
- usleep_range(1000, 2000);
- rc = access_ereg(phydev, PHYACC_ATTR_MODE_READ,
- PHYACC_ATTR_BANK_SMI, 0x00, 0);
+ /* phy Soft reset */
+ rc = genphy_soft_reset(phydev);
if (rc < 0)
return rc;
- if ((rc & 0x8000) != 0)
- return -ETIMEDOUT;
/* PHY Initialization */
for (i = 0; i < ARRAY_SIZE(init); i++) {
- if (init[i].mode == PHYACC_ATTR_MODE_MODIFY) {
- rc = access_ereg_modify_changed(phydev, init[i].bank,
- init[i].offset,
- init[i].val,
- init[i].mask);
+ if (init[i].mode == PHYACC_ATTR_MODE_POLL) {
+ rc = access_ereg_clr_poll_timeout(phydev, init[i].bank,
+ init[i].offset,
+ init[i].val,
+ init[i].mask);
} else {
rc = access_ereg(phydev, init[i].mode, init[i].bank,
init[i].offset, init[i].val);
@@ -231,6 +400,9 @@ static int lan87xx_config_init(struct phy_device *phydev)
{
int rc = lan87xx_phy_init(phydev);
+ if (rc < 0)
+ phydev_err(phydev, "failed to initialize phy\n");
+
return rc < 0 ? rc : 0;
}
@@ -462,32 +634,67 @@ static int lan87xx_cable_test_get_status(struct phy_device *phydev,
return 0;
}
-static struct phy_driver microchip_t1_phy_driver[] = {
- {
- .phy_id = 0x0007c150,
- .phy_id_mask = 0xfffffff0,
- .name = "Microchip LAN87xx T1",
- .flags = PHY_POLL_CABLE_TEST,
+static int lan937x_read_status(struct phy_device *phydev)
+{
+ int val;
- .features = PHY_BASIC_T1_FEATURES,
+ val = phy_read(phydev, T1_MODE_STAT_REG);
- .config_init = lan87xx_config_init,
+ if (val < 0)
+ return val;
- .config_intr = lan87xx_phy_config_intr,
- .handle_interrupt = lan87xx_handle_interrupt,
+ if (val & T1_LINK_UP_MSK)
+ phydev->link = 1;
+ else
+ phydev->link = 0;
+
+ phydev->duplex = DUPLEX_FULL;
+ phydev->speed = SPEED_100;
+ phydev->pause = 0;
+ phydev->asym_pause = 0;
- .suspend = genphy_suspend,
- .resume = genphy_resume,
+ return 0;
+}
+
+static int lan937x_config_init(struct phy_device *phydev)
+{
+ /* lan87xx & lan937x follows same init sequence */
+ return lan87xx_config_init(phydev);
+}
+
+static struct phy_driver microchip_t1_phy_driver[] = {
+ {
+ .phy_id = LAN87XX_PHY_ID,
+ .phy_id_mask = LAN87XX_PHY_ID_MASK,
+ .name = "LAN87xx T1",
+ .flags = PHY_POLL_CABLE_TEST,
+ .features = PHY_BASIC_T1_FEATURES,
+ .config_init = lan87xx_config_init,
+ .config_intr = lan87xx_phy_config_intr,
+ .handle_interrupt = lan87xx_handle_interrupt,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
.cable_test_start = lan87xx_cable_test_start,
.cable_test_get_status = lan87xx_cable_test_get_status,
+ },
+ {
+ .phy_id = LAN937X_T1_PHY_ID,
+ .phy_id_mask = LAN937X_PHY_ID_MASK,
+ .name = "LAN937x T1",
+ .read_status = lan937x_read_status,
+ .features = PHY_BASIC_T1_FEATURES,
+ .config_init = lan937x_config_init,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
}
};
module_phy_driver(microchip_t1_phy_driver);
static struct mdio_device_id __maybe_unused microchip_t1_tbl[] = {
- { 0x0007c150, 0xfffffff0 },
- { }
+ { LAN87XX_PHY_ID, LAN87XX_PHY_ID_MASK },
+ { LAN937X_T1_PHY_ID, LAN937X_PHY_ID_MASK },
+ {}
};
MODULE_DEVICE_TABLE(mdio, microchip_t1_tbl);
--
2.27.0