Re: [PATCH v3] firmware: arm_scmi: Free mailbox channels if probe fails

[Sudeep Holla]

On Mon, Nov 01, 2021 at 09:35:42AM -0700, rishabhb@xxxxxxxxxxxxxx wrote:
> On 2021-09-01 02:35, Cristian Marussi wrote:
> > On Tue, Aug 31, 2021 at 06:48:35AM +0100, Cristian Marussi wrote:
> > > On Mon, Aug 30, 2021 at 02:09:37PM -0700, rishabhb@xxxxxxxxxxxxxx
> > > wrote:
> > > > Hi Christian
> > > 
> > > Hi Rishabh,
> > > 
> > > thanks for looking into this kind of bad interactions.
> > > 
> > > > There seems to be another issue here. The response from agent can be delayed
> > > > causing a timeout during base protocol acquire,
> > > > which leads to the probe failure. What I have observed is sometimes the
> > > > failure of probe and rx_callback (due to a delayed message)
> > > > happens at the same time on different cpus.
> > > > Because of this race, the device memory may be cleared while the
> > > > interrupt(rx_callback) is executing on another cpu.
> > > 
> > > You are right that concurrency was not handled properly in this kind
> > > of
> > > context and moreover, if you think about it, even the case of out of
> > > order reception of responses and delayed_responses (type2 SCMI
> > > messages)
> > > for asynchronous SCMI commands was not handled properly.
> > > 
> > > > How do you propose we solve this? Do you think it is better to take the
> > > > setting up of base and other protocols out of probe and
> > > > in some delayed work? That would imply the device memory is not released
> > > > until remove is called. Or should we add locking to
> > > > the interrupt handler(scmi_rx_callback) and the cleanup in probe to avoid
> > > > the race?
> > > >
> > > 
> > > These issues were more easily exposed by SCMI Virtio transport, so in
> > > the series where I introduced scmi-virtio:
> > > 
> > > https://lore.kernel.org/linux-arm-kernel/162848483974.232214.9506203742448269364.b4-ty@xxxxxxx/
> > > 
> > > (which is now queued for v5.15 ...  now on -next I think...finger
> > > crossed)
> > > 
> > > I took the chance to rectify a couple of other things in the SCMI core
> > > in the initial commits.
> > > As an example, in the above series
> > > 
> > >  [PATCH v7 05/15] firmware: arm_scmi: Handle concurrent and
> > > out-of-order messages
> > > 
> > > cares to add a refcount to xfers and some locking on xfers between TX
> > > and RX path to avoid that a timed out xfer can vanish while the rx
> > > path
> > > is concurrently working on it (as you said); moreover I handle the
> > > condition (rare if not unplausible anyway) in which a transport
> > > delivers
> > > out of order responses and delayed responses.
> > > 
> > > I tested this scenarios on some fake emulated SCMI Virtio transport
> > > where I could play any sort of mess and tricks to stress this limit
> > > conditions, but you're more than welcome to verify if the race you are
> > > seeing on Base protocol time out is solved (as I would hope :D) by
> > > this
> > > series of mine.
> > > 
> > > Let me know, any feedback is welcome.
> > > 
> > > Btw, in the series above there are also other minor changes, but there
> > > is also another more radical change needed to ensure correctness and
> > > protection against stale old messages which maybe could interest you
> > > in general if you are looking into SCMI:
> > > 
> > > [PATCH v7 04/15] firmware: arm_scmi: Introduce monotonically
> > > increasing tokens
> > > 
> > > Let me know if yo have other concerns.
> > > 
> > 
> > Hi Rishabhb,
> > 
> > just a quick remark, thinking again about your fail @probe scenario
> > above
> > I realized that while the concurrency patch I mentioned above could help
> > on
> > races against vanishing xfers when late timed-out responses are
> > delivered,
> > here we really are then also shutting down everything on failure, so
> > there
> > could be further issues between a very late invokation of
> > scmi_rx_callback
> > and the core devm_ helpers freeing the underlying xfer/cinfo/etc..
> > structs
> > used by scmi-rx-callback itself (maybe this was already what you meant
> > and
> > I didn't get it,...sorry)
> > 
> > On the other side, I don't feel that delaying Base init to a deferred
> > worker is a viable solution since we need Base protocol init to be
> > initialized and we need to just give up if we cannot communicate with
> > the SCMI platform fw in such early stages. (Base protocol is really the
> > only mandatory proto is I remember correctly the spec)
> > 
> > Currenly I'm off and only glancing at mails but I'll have a thought
> > about
> > these issues once back in a few weeks time.
> > 
> > Thanks,
> > Cristian
> > 
> Hi Cristian
> I hope you enjoyed your vacation. Did you get a chance to look at the issue
> stated above and have some idea as to how to solve this?

Do you still see the issue with v5.15 ? Can you please check if haven't
already done that ?

Also 30ms delay we have is huge IMO and we typically expect the communication
with remote processor or any entity that implements SCMI to happen in terms
of one or few ms tops.

If there is a race, we need to fix that but I am interested in knowing
why the default time of 30ms not sufficient ? Did increasing that helps
and is this timeout happening only for the initial commands(guessing the
SCMI firmware is not yet ready) or does it happen even during run-time ?

-- 
Regards,
Sudeep