Re: [PATCH v1 3/3] Bluetooth: hci_qca: Add support for QTI bluetooth MAPLE

From: Greg KH
Date: Tue Nov 02 2021 - 09:23:09 EST

Next message: Dan Carpenter: "Re: [PATCH] binder: don't detect sender/target during buffer cleanup"
Previous message: Thierry Reding: "Re: [PATCH 2/2] gpio: tegra186: Add support for Tegra234 gpio"
In reply to: Zijun Hu: "Re: [PATCH v1 3/3] Bluetooth: hci_qca: Add support for QTI bluetooth MAPLE"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, Nov 02, 2021 at 04:54:23PM +0800, Zijun Hu wrote:
>
>
> On 11/2/2021 4:22 PM, Greg KH wrote:
> > On Tue, Nov 02, 2021 at 03:53:33PM +0800, Zijun Hu wrote:
> >>
> >>
> >> On 11/2/2021 3:35 PM, Greg KH wrote:
> >>> On Tue, Nov 02, 2021 at 03:12:57PM +0800, Zijun Hu wrote:
> >>>> From: Zijun Hu <quic_zijuhu@xxxxxxxxxxx>
> >>>>
> >>>> Add support for MAPLE integrated within SOC, it is mounted on
> >>>> a virtual tty port and powered on/off via relevant IOCTL, neither
> >>>> IBS nor RAMPATCH downloading is not required.
> >>>>
> >>>> Signed-off-by: Zijun Hu <quic_zijuhu@xxxxxxxxxxx>
> >>>> ---
> >>>> drivers/bluetooth/btqca.c | 13 ++++++++++++-
> >>>> drivers/bluetooth/btqca.h | 13 +++++++++++++
> >>>> drivers/bluetooth/hci_qca.c | 47 ++++++++++++++++++++++++++++++++++++++++++++-
> >>>> 3 files changed, 71 insertions(+), 2 deletions(-)
> >>>>
> >>>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> >>>> index be04d74037d2..b83d2ecefe5d 100644
> >>>> --- a/drivers/bluetooth/btqca.c
> >>>> +++ b/drivers/bluetooth/btqca.c
> >>>> @@ -255,6 +255,8 @@ static void qca_tlv_check_data(struct hci_dev *hdev,
> >>>> BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
> >>>> BT_DBG("Length\t\t : %d bytes", length);
> >>>>
> >>>> + if (qca_is_maple(soc_type))
> >>>> + break;
> >>>> idx = 0;
> >>>> data = tlv->data;
> >>>> while (idx < length) {
> >>>> @@ -552,6 +554,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> >>>> rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
> >>>>
> >>>> /* Download rampatch file */
> >>>> + if (qca_is_maple(soc_type))
> >>>> + goto download_nvm;
> >>>> +
> >>>> config.type = TLV_TYPE_PATCH;
> >>>> if (qca_is_wcn399x(soc_type)) {
> >>>> snprintf(config.fwname, sizeof(config.fwname),
> >>>> @@ -580,6 +585,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> >>>> /* Give the controller some time to get ready to receive the NVM */
> >>>> msleep(10);
> >>>>
> >>>> +download_nvm:
> >>>> /* Download NVM configuration */
> >>>> config.type = TLV_TYPE_NVM;
> >>>> if (firmware_name)
> >>>> @@ -597,6 +603,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> >>>> else if (soc_type == QCA_QCA6390)
> >>>> snprintf(config.fwname, sizeof(config.fwname),
> >>>> "qca/htnv%02x.bin", rom_ver);
> >>>> + else if (qca_is_maple(soc_type))
> >>>> + snprintf(config.fwname, sizeof(config.fwname),
> >>>> + "qca/mpnv%02x.bin", rom_ver);
> >>>> else if (soc_type == QCA_WCN6750)
> >>>> snprintf(config.fwname, sizeof(config.fwname),
> >>>> "qca/msnv%02x.bin", rom_ver);
> >>>> @@ -609,6 +618,8 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> >>>> bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
> >>>> return err;
> >>>> }
> >>>> + if (qca_is_maple(soc_type))
> >>>> + msleep(MAPLE_NVM_READY_DELAY_MS);
> >>>>
> >>>> if (soc_type >= QCA_WCN3991) {
> >>>> err = qca_disable_soc_logging(hdev);
> >>>> @@ -637,7 +648,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> >>>> return err;
> >>>> }
> >>>>
> >>>> - if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750) {
> >>>> + if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750 || qca_is_maple(soc_type)) {
> >>>> /* get fw build info */
> >>>> err = qca_read_fw_build_info(hdev);
> >>>> if (err < 0)
> >>>> diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
> >>>> index 30afa7703afd..0a5a7d1daa71 100644
> >>>> --- a/drivers/bluetooth/btqca.h
> >>>> +++ b/drivers/bluetooth/btqca.h
> >>>> @@ -46,6 +46,8 @@
> >>>>
> >>>> #define QCA_FW_BUILD_VER_LEN 255
> >>>>
> >>>> +#define MAPLE_NVM_READY_DELAY_MS 1500
> >>>> +#define MAPLE_POWER_CONTROL_DELAY_MS 50
> >>>>
> >>>> enum qca_baudrate {
> >>>> QCA_BAUDRATE_115200 = 0,
> >>>> @@ -145,6 +147,7 @@ enum qca_btsoc_type {
> >>>> QCA_WCN3991,
> >>>> QCA_QCA6390,
> >>>> QCA_WCN6750,
> >>>> + QCA_MAPLE,
> >>>> };
> >>>>
> >>>> #if IS_ENABLED(CONFIG_BT_QCA)
> >>>> @@ -167,6 +170,11 @@ static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
> >>>> return soc_type == QCA_WCN6750;
> >>>> }
> >>>>
> >>>> +static inline bool qca_is_maple(enum qca_btsoc_type soc_type)
> >>>> +{
> >>>> + return soc_type == QCA_MAPLE;
> >>>> +}
> >>>> +
> >>>> #else
> >>>>
> >>>> static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
> >>>> @@ -204,6 +212,11 @@ static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
> >>>> return false;
> >>>> }
> >>>>
> >>>> +static inline bool qca_is_maple(enum qca_btsoc_type soc_type)
> >>>> +{
> >>>> + return false;
> >>>> +}
> >>>> +
> >>>> static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
> >>>> {
> >>>> return -EOPNOTSUPP;
> >>>> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> >>>> index dd768a8ed7cb..f1d9670719c4 100644
> >>>> --- a/drivers/bluetooth/hci_qca.c
> >>>> +++ b/drivers/bluetooth/hci_qca.c
> >>>> @@ -70,6 +70,10 @@
> >>>> #define QCA_CRASHBYTE_PACKET_LEN 1096
> >>>> #define QCA_MEMDUMP_BYTE 0xFB
> >>>>
> >>>> +#ifndef IOCTL_IPC_BOOT
> >>>> +#define IOCTL_IPC_BOOT 0xBE
> >>>> +#endif
> >>>
> >>> You send this command, but never use it. Where is the driver code that
> >>> uses this command?
> >>>
> >> qca_maple_power_control() will use it. this driver depends on bt_tty kernel module
> >> https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/tree/drivers/soc/qcom/bt_tty.c?h=NHSS.QSDK.11.5.0.5.r2
> >
> > You can not add code to the kernel that is not used by the kernel
> > itself. That driver needs to be in the tree as well, why is it not
> > submitted now too?
> >
> the bt_tty driver module is not developed and maintained by me.
> bluetooth driver code of linux-ipq-5.4 stopped update at Sep 15 2019.
> many relevant changes need to be picked up from bluetooth-next if apply this patch int to linux-ipq-5.4
>
> >>> And why not tabs?
> >>>
> >>> And why is this patch series not properly threaded so tools can pick it
> >>> up and find them?
> >>>
> >>> And why the odd named ioctl that is different from other ones in this
> >>> file?
> >>>
> >> that IOCTL name is defined by that module.
> >> https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/tree/include/linux/bt.h?h=NHSS.QSDK.11.5.0.5.r2
> >
> > Again, it needs to be in the tree.
> >
> make sense, i will try to submit this change to linux-ipq-5.4

"linux-ipq-5.4" has NOTHING to do with the upstream kernel development
process here. Please work with the developers at your company to
understand how the kernel development process works to help understand
this correctly, before submitting patches again.

thanks,

greg k-h

Next message: Dan Carpenter: "Re: [PATCH] binder: don't detect sender/target during buffer cleanup"
Previous message: Thierry Reding: "Re: [PATCH 2/2] gpio: tegra186: Add support for Tegra234 gpio"
In reply to: Zijun Hu: "Re: [PATCH v1 3/3] Bluetooth: hci_qca: Add support for QTI bluetooth MAPLE"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]