Re: [PATCH v2 12/13] ARM: dts: imx: add i.MXRT1050-EVK support

[Jesse Taube]

On 11/2/21 19:54, Jesse Taube wrote:
> On 11/2/21 19:42, Fabio Estevam wrote:
> > On Tue, Nov 2, 2021 at 7:57 PM Jesse Taube <mr.bossman075@xxxxxxxxx> wrote:
> >
> > > +/ {
> > > +       model = "NXP IMXRT1050-evk board";
> > > +       compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
> > > +
> > > +       chosen {
> > > +               bootargs = "root=/dev/ram";
> >
> > No need to pass bootargs here.
> >
> > > +               stdout-path = &lpuart1;
> > > +       };
> > > +
> > > +       aliases {
> > > +               gpio0 = &gpio1;
> > > +               gpio1 = &gpio2;
> > > +               gpio2 = &gpio3;
> > > +               gpio3 = &gpio4;
> > > +               gpio4 = &gpio5;
> > > +               mmc0 = &usdhc1;
> > > +               serial0 = &lpuart1;
> > > +       };
> > > +
> > > +       memory@0 {
> >
> > memory@80000000
> >
> > Building with W=1 should give a dtc warning due to the unit address
> > and reg mismatch.
> Oh that makes sense.
> I guess I'm going to have to figure out how to get warnings to work as I
> couldn't last time I tried.
Oh i got it to work I did something dumb...
I didn't give a warning for this i still changed it of course.
> > > +               device_type = "memory";
> > > +               reg = <0x80000000 0x2000000>;
> > > +       };
> > > +
> >
> > Unneeded blank line.
> > > +
> > > +&iomuxc {
> > > +       pinctrl-names = "default";
> > > +
> > > +       imxrt1050-evk {
> >
> > No need for this imxrt1050-evk container.
> I was wondering if that was needed, u-boot has it, good to know.
> > > +               pinctrl_lpuart1: lpuart1grp {
> > > +                       fsl,pins = <
> > > +                               MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD
> > > +                                       0xf1
> >
> > Put it on a single line. It helps readability. Same applies globally.
> > > +&usdhc1 {
> > > +       pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> > > +       pinctrl-0 = <&pinctrl_usdhc0>;
> > > +       pinctrl-1 = <&pinctrl_usdhc0>;
> > > +       pinctrl-2 = <&pinctrl_usdhc0>;
> > > +       pinctrl-3 = <&pinctrl_usdhc0>;
> > > +       status = "okay";
> > > +
> > > +       cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
> >
> > Make 'status' to be the last property. Remove the blank line.
> >
> > > +               edma1: dma-controller@400e8000 {
> > > +                       #dma-cells = <2>;
> > > +                       compatible = "fsl,imx7ulp-edma";
> > > +                       reg = <0x400e8000 0x4000>,
> > > +                               <0x400ec000 0x4000>;
> > > +                       dma-channels = <32>;
> > > +                       interrupts = <0>,
> > > +                               <1>,
> > > +                               <2>,
> > > +                               <3>,
> > > +                               <4>,
> > > +                               <5>,
> > > +                               <6>,
> > > +                               <7>,
> > > +                               <8>,
> > > +                               <9>,
> > > +                               <10>,
> > > +                               <11>,
> > > +                               <12>,
> > > +                               <13>,
> > > +                               <14>,
> > > +                               <15>,
> > > +                               <16>;
> >
> > Please group more elements into the same line.
> >
> > Putting one entry per line makes it extremely long.
> >
> > > +               gpio5: gpio@400c0000 {
> > > +                       compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio";
> > > +                       reg = <0x400c0000 0x4000>;
> > > +                       interrupts = <88>,
> > > +                               <89>;
> >
> > Put the interrupts into a single line.
> Ah all these make sense, will fix, sry about that.