[PATCH v8 8/8] PCI: brcmstb: Add control of subdevice voltage regulators

[Jim Quinlan]

This Broadcom STB PCIe RC driver has one port and connects directly to one
device, be it a switch or an endpoint.  We want to be able to leverage
the recently added mechansim that allocates and turns on/off subdevice
regulators.

All that needs to be done is to put the regulator DT nodes in the bridge
below host and to set the pci_ops methods add_bus and remove_bus.

Note that the pci_subdev_regulators_add_bus() method is wrapped for two
reasons:

   1. To acheive linkup after the voltage regulators are turned on.

   2. If, in the case of an unsuccessful linkup, to redirect
      any PCIe accesses to subdevices, e.g. the scan for
      DEV/ID.  This redirection is needed because the Broadcom
      PCIe HW wil issue a CPU abort if such an access is made when
      there is no linkup.

Signed-off-by: Jim Quinlan <jim2101024@xxxxxxxxx>
---
 drivers/pci/controller/pcie-brcmstb.c | 56 ++++++++++++++++++++++++++-
 1 file changed, 55 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 1a841c240abb..692df3dda77a 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -191,6 +191,7 @@ static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie,
 static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val);
 static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
 static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
+static int brcm_pcie_add_bus(struct pci_bus *bus);
 
 enum {
 	RGR1_SW_INIT_1,
@@ -295,6 +296,7 @@ struct brcm_pcie {
 	u32			hw_rev;
 	void			(*perst_set)(struct brcm_pcie *pcie, u32 val);
 	void			(*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
+	bool			refusal_mode;
 };
 
 /*
@@ -711,6 +713,18 @@ static void __iomem *brcm_pcie_map_conf(struct pci_bus *bus, unsigned int devfn,
 	/* Accesses to the RC go right to the RC registers if slot==0 */
 	if (pci_is_root_bus(bus))
 		return PCI_SLOT(devfn) ? NULL : base + where;
+	if (pcie->refusal_mode) {
+		/*
+		 * At this point we do not have link.  There will be a CPU
+		 * abort -- a quirk with this controller --if Linux tries
+		 * to read any config-space registers besides those
+		 * targeting the host bridge.  To prevent this we hijack
+		 * the address to point to a safe access that will return
+		 * 0xffffffff.
+		 */
+		writel(0xffffffff, base + PCIE_MISC_RC_BAR2_CONFIG_HI);
+		return base + PCIE_MISC_RC_BAR2_CONFIG_HI + (where & 0x3);
+	}
 
 	/* For devices, write to the config space index register */
 	idx = PCIE_ECAM_OFFSET(bus->number, devfn, 0);
@@ -722,6 +736,8 @@ static struct pci_ops brcm_pcie_ops = {
 	.map_bus = brcm_pcie_map_conf,
 	.read = pci_generic_config_read,
 	.write = pci_generic_config_write,
+	.add_bus = brcm_pcie_add_bus,
+	.remove_bus = pci_subdev_regulators_remove_bus,
 };
 
 static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val)
@@ -1242,6 +1258,34 @@ static const struct of_device_id brcm_pcie_match[] = {
 	{},
 };
 
+static int brcm_pcie_add_bus(struct pci_bus *bus)
+{
+	struct pci_host_bridge *hb;
+	struct brcm_pcie *pcie;
+	int ret;
+
+	if (!pcie_is_port_dev(bus->self))
+		return 0;
+
+	hb = pci_find_host_bridge(bus);
+	pcie = (struct brcm_pcie *) hb->sysdata;
+
+	ret = pci_subdev_regulators_add_bus(bus);
+	if (ret)
+		return ret;
+
+	/*
+	 * If we have failed linkup there is no point to return an error as
+	 * currently it will cause a WARNING() from pci_alloc_child_bus().
+	 * We return 0 and turn on the "refusal_mode" so that any further
+	 * accesses to the pci_dev just get 0xffffffff
+	 */
+	if (brcm_pcie_linkup(pcie) != 0)
+		pcie->refusal_mode = true;
+
+	return 0;
+}
+
 static int brcm_pcie_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node, *msi_np;
@@ -1333,7 +1377,17 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, pcie);
 
-	return pci_host_probe(bridge);
+	ret = pci_host_probe(bridge);
+	if (!ret && !brcm_pcie_link_up(pcie))
+		ret = -ENODEV;
+
+	if (ret) {
+		brcm_pcie_remove(pdev);
+		return ret;
+	}
+
+	return 0;
+
 fail:
 	__brcm_pcie_remove(pcie);
 	return ret;
-- 
2.17.1