Re: [PATCH v10, 00/19] Support multi hardware decode using of_platform_populate
From: Ezequiel Garcia
Date: Sun Nov 14 2021 - 17:07:39 EST
Hi Yunfei,
On Thu, 11 Nov 2021 at 01:15, Yunfei Dong <yunfei.dong@xxxxxxxxxxxx> wrote:
>
> This series adds support for multi hardware decode into mtk-vcodec, by first adding use
> of_platform_populate to manage each hardware information: interrupt, clock, register
> bases and power. Secondly add core work queue to deal with core hardware message,
> at the same time, add msg queue for different hardware share messages. Lastly, the
> architecture of different specs are not the same, using specs type to separate them.
>
> This series has been tested with both MT8183 and MT8173. Decoding was working for both chips.
>
How are you testing Decoding? If you are running some test suite, it would
be good to add such information.
Are you testing some edge-cases such as parallel/concurrent decoding,
removing the driver while streaming, and so on? This should help catch
some typical issues.
Thanks,
Ezequiel
> Patches 1~3 rewrite get register bases and power on/off interface.
> Patches 4 export decoder pm interfaces.
> Patches 5 add to support 8192.
> Patch 6 support multi hardware.
> Patch 7 separate video encoder and decoder document
> Patch 8-17 add interfaces to support core hardware.
> Patch 18-19 remove mtk_vcodec_release_dec/enc_pm interfaces.
> ---
> changes compared with v9:
> - need not to build ko, just export pm interfaces for patch 04/19.
> - fix comments for patch 06/19
>
> changes compared with v8:
> - add new patch 18~19 to remove mtk_vcodec_release_de/enc_pm interfaces.
> - fix spelling mistakes for patch 17/19
> - fix yaml comments for patch 15/19
>
> Changes compared with v7:
> - add new patch 4 to build decoder pm file as module
> - add new patch 5 to support 8192
> - fix comments for patch 6/17
> - change some logic for using work queue instead of create thread for core hardware decode for patch 10/17
> - using work queue for hardware decode instead of create thread for patch 13/17
> - add returen value for patch 14/17
> - fix yaml check fail 15/17
>
> Changes compared with v6:
> - Use of_platform_populate to manage multi hardware, not component framework for patch 4/15
> - Re-write dtsi document for hardware architecture changed for patch 13/15 -The dtsi will write like below in patch 13/15:
> vcodec_dec: vcodec_dec@16000000 {
> compatible = "mediatek,mt8192-vcodec-dec";
> #address-cells = <2>;
> #size-cells = <2>;
> ranges;
> reg = <0 0x16000000 0 0x1000>; /* VDEC_SYS */
> mediatek,scp = <&scp>;
> iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>;
> dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>;
> vcodec_lat {
> compatible = "mediatek,mtk-vcodec-lat";
> reg = <0 0x16010000 0 0x800>; /* VDEC_MISC */
> reg-name = "reg-misc";
> interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH 0>;
> iommus = <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD2_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_AVC_MV_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_PRED_RD_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_TILE_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_WDMA_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_LAT0_RG_CTRL_DMA_EXT>,
> <&iommu0 M4U_PORT_L5_VDEC_UFO_ENC_EXT>;
> clocks = <&topckgen CLK_TOP_VDEC_SEL>,
> <&vdecsys_soc CLK_VDEC_SOC_VDEC>,
> <&vdecsys_soc CLK_VDEC_SOC_LAT>,
> <&vdecsys_soc CLK_VDEC_SOC_LARB1>,
> <&topckgen CLK_TOP_MAINPLL_D4>;
> clock-names = "vdec-sel", "vdec-soc-vdec", "vdec-soc-lat",
> "vdec-vdec", "vdec-top";
> assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>;
> assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D4>;
> power-domains = <&spm MT8192_POWER_DOMAIN_VDEC>;
> };
>
> vcodec_core {
> compatible = "mediatek,mtk-vcodec-core";
> reg = <0 0x16025000 0 0x1000>; /* VDEC_CORE_MISC */
> reg-names = "reg-misc";
> interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH 0>;
> iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_UFO_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_PP_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_PRED_RD_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_PRED_WR_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_PPWRAP_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_TILE_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_VLD_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_VLD2_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_AVC_MV_EXT>,
> <&iommu0 M4U_PORT_L4_VDEC_RG_CTRL_DMA_EXT>;
> clocks = <&topckgen CLK_TOP_VDEC_SEL>,
> <&vdecsys CLK_VDEC_VDEC>,
> <&vdecsys CLK_VDEC_LAT>,
> <&vdecsys CLK_VDEC_LARB1>,
> <&topckgen CLK_TOP_MAINPLL_D4>;
> clock-names = "vdec-sel", "vdec-soc-vdec", "vdec-soc-lat",
> "vdec-vdec", "vdec-top";
> assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>;
> assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D4>;
> power-domains = <&spm MT8192_POWER_DOMAIN_VDEC2>;
> };
> };
>
> Changes compared with v5:
> - Add decoder hardware block diagram for patch 13/15
>
> Changes compared with v4:
> - Fix comments for patch 4/15
> >> + if (dev->is_comp_supported) {
> >> + ret = mtk_vcodec_init_master(dev);
> >> + if (ret < 0)
> >> + goto err_component_match;
> >> + } else {
> >> + platform_set_drvdata(pdev, dev);
> >> + }
> Fix platform_set_drvdata.
> - Fix build error for patch 9/15
> - Add depend patch in case of error header file for patch 13/15
>
> Changes compared with v3:
> - Fix return value for patch 1/15
> - Fix comments for patch 4/15
> > Looking up "mediatek,mtk-vcodec-core" to determine if it uses component framwork sounds like...
> Add prameter in pdata, for all platform will use compoent after mt8183
>
> >> + if (dev->is_comp_supported) {
> >> + ret = mtk_vcodec_init_master(dev);
> >> + if (ret < 0)
> >> + goto err_component_match;
> >> + } else {
> >> + platform_set_drvdata(pdev, dev);
> >> + }
> > + Has asked the same question in [1]. Why it removes the
> > +platform_set_drvdata() above? mtk_vcodec_init_master() also calls platform_set_drvdata().
> Must call component_master_add_with_match after platform_set_drvdata for component architecture.
> - Fix yaml files check fail for patch 5/15
> - Fix yaml file check fail for patch 14/15
>
> Changes compared with v1:
> - Fix many comments for patch 3/14
> - Remove unnecessary code for patch 4/14
> - Using enum mtk_vdec_hw_count instead of magic numbers for patch 6/14
> - Reconstructed get/put lat buffer for lat and core hardware for patch 7/14
> - Using yaml format to instead of txt file for patch 12/14
>
> Yunfei Dong (19):
> media: mtk-vcodec: Get numbers of register bases from DT
> media: mtk-vcodec: Align vcodec wake up interrupt interface
> media: mtk-vcodec: Refactor vcodec pm interface
> media: mtk-vcodec: export decoder pm functions
> media: mtk-vcodec: Support MT8192
> media: mtk-vcodec: Manage multi hardware information
> dt-bindings: media: mtk-vcodec: Separate video encoder and decoder
> dt-bindings
> media: mtk-vcodec: Use pure single core for MT8183
> media: mtk-vcodec: Add irq interface for multi hardware
> media: mtk-vcodec: Add msg queue feature for lat and core architecture
> media: mtk-vcodec: Generalize power and clock on/off interfaces
> media: mtk-vcodec: Add new interface to lock different hardware
> media: mtk-vcodec: Add work queue for core hardware decode
> media: mtk-vcodec: Support 34bits dma address for vdec
> dt-bindings: media: mtk-vcodec: Adds decoder dt-bindings for mt8192
> media: mtk-vcodec: Add core dec and dec end ipi msg
> media: mtk-vcodec: Use codec type to separate different hardware
> media: mtk-vcodec: Remove mtk_vcodec_release_dec_pm
> media: mtk-vcodec: Remove mtk_vcodec_release_enc_pm
>
> .../media/mediatek,vcodec-decoder.yaml | 176 +++++++++++
> .../media/mediatek,vcodec-encoder.yaml | 187 ++++++++++++
> .../media/mediatek,vcodec-subdev-decoder.yaml | 261 ++++++++++++++++
> .../bindings/media/mediatek-vcodec.txt | 131 --------
> drivers/media/platform/mtk-vcodec/Makefile | 6 +-
> .../platform/mtk-vcodec/mtk_vcodec_dec.c | 4 +-
> .../platform/mtk-vcodec/mtk_vcodec_dec.h | 1 +
> .../platform/mtk-vcodec/mtk_vcodec_dec_drv.c | 219 +++++++++++---
> .../platform/mtk-vcodec/mtk_vcodec_dec_hw.c | 172 +++++++++++
> .../platform/mtk-vcodec/mtk_vcodec_dec_hw.h | 55 ++++
> .../platform/mtk-vcodec/mtk_vcodec_dec_pm.c | 104 +++++--
> .../platform/mtk-vcodec/mtk_vcodec_dec_pm.h | 12 +-
> .../mtk-vcodec/mtk_vcodec_dec_stateful.c | 2 +
> .../mtk-vcodec/mtk_vcodec_dec_stateless.c | 20 ++
> .../platform/mtk-vcodec/mtk_vcodec_drv.h | 75 ++++-
> .../platform/mtk-vcodec/mtk_vcodec_enc_drv.c | 21 +-
> .../platform/mtk-vcodec/mtk_vcodec_enc_pm.c | 10 +-
> .../platform/mtk-vcodec/mtk_vcodec_enc_pm.h | 3 +-
> .../platform/mtk-vcodec/mtk_vcodec_intr.c | 27 +-
> .../platform/mtk-vcodec/mtk_vcodec_intr.h | 4 +-
> .../platform/mtk-vcodec/mtk_vcodec_util.c | 87 +++++-
> .../platform/mtk-vcodec/mtk_vcodec_util.h | 8 +-
> .../platform/mtk-vcodec/vdec/vdec_h264_if.c | 2 +-
> .../mtk-vcodec/vdec/vdec_h264_req_if.c | 2 +-
> .../platform/mtk-vcodec/vdec/vdec_vp8_if.c | 2 +-
> .../platform/mtk-vcodec/vdec/vdec_vp9_if.c | 2 +-
> .../media/platform/mtk-vcodec/vdec_drv_if.c | 21 +-
> .../media/platform/mtk-vcodec/vdec_ipi_msg.h | 16 +-
> .../platform/mtk-vcodec/vdec_msg_queue.c | 286 ++++++++++++++++++
> .../platform/mtk-vcodec/vdec_msg_queue.h | 148 +++++++++
> .../media/platform/mtk-vcodec/vdec_vpu_if.c | 46 ++-
> .../media/platform/mtk-vcodec/vdec_vpu_if.h | 22 ++
> .../platform/mtk-vcodec/venc/venc_h264_if.c | 2 +-
> .../platform/mtk-vcodec/venc/venc_vp8_if.c | 2 +-
> 34 files changed, 1841 insertions(+), 295 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml
> create mode 100644 Documentation/devicetree/bindings/media/mediatek,vcodec-encoder.yaml
> create mode 100644 Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml
> delete mode 100644 Documentation/devicetree/bindings/media/mediatek-vcodec.txt
> create mode 100644 drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.c
> create mode 100644 drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.h
> create mode 100644 drivers/media/platform/mtk-vcodec/vdec_msg_queue.c
> create mode 100644 drivers/media/platform/mtk-vcodec/vdec_msg_queue.h
>
> --
> 2.25.1
>