Re: [PATCH V2 4/5] arm64: dts: imx8mm-beacon: Enable OV5640 Camera

[Laurent Pinchart]

Hi Adam,

Thank you for the patch.

On Sat, Nov 06, 2021 at 10:54:26AM -0500, Adam Ford wrote:
> The baseboard has support for a TDNext 5640 Camera which
> uses an OV5640 connected to a 2-lane CSI2 interface.
> 
> With the CSI and mipi_csi2 drivers pointing to an OV5640 camera, the media
> pipeline can be configured with the following:
> 
>     media-ctl --links "'ov5640 1-003c':0->'imx7-mipi-csis.0':0[1]"
> 
> The camera and various nodes in the pipeline can be configured for UYVY:
>     media-ctl -v -V "'ov5640 1-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
>     media-ctl -v -V "'csi':0 [fmt:UYVY8_1X16/640x480 field:none]"
> 
> Signed-off-by: Adam Ford <aford173@xxxxxxxxx>

As the ov5640 is on an add-on module, would a DT overlay be better ?

> ---
> V2:  No change
> 
>  .../freescale/imx8mm-beacon-baseboard.dtsi    | 58 +++++++++++++++++++
>  1 file changed, 58 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> index 6f5e63696ec0..0fb95f4a5e78 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> @@ -43,6 +43,16 @@ reg_audio: regulator-audio {
>  		enable-active-high;
>  	};
>  
> +	reg_camera: regulator-camera {
> +		compatible = "regulator-fixed";
> +		regulator-name = "mipi_pwr";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		startup-delay-us = <100000>;
> +	};
> +
>  	reg_usdhc2_vmmc: regulator-usdhc2 {
>  		compatible = "regulator-fixed";
>  		regulator-name = "VSD_3V3";
> @@ -67,6 +77,10 @@ sound {
>  	};
>  };
>  
> +&csi {
> +	status = "okay";
> +};
> +
>  &ecspi2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_espi2>;
> @@ -90,6 +104,30 @@ &i2c2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_i2c2>;
>  	status = "okay";
> +
> +	camera@3c {
> +		compatible = "ovti,ov5640";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_ov5640>;
> +		reg = <0x3c>;
> +		clocks = <&clk IMX8MM_CLK_CLKO1>;
> +		clock-names = "xclk";
> +		assigned-clocks = <&clk IMX8MM_CLK_CLKO1>;
> +		assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
> +		assigned-clock-rates = <24000000>;
> +		AVDD-supply = <&reg_camera>;  /* 2.8v */
> +		powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> +		reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> +
> +		port {
> +			/* MIPI CSI-2 bus endpoint */
> +			ov5640_to_mipi_csi2: endpoint {
> +				remote-endpoint = <&imx8mm_mipi_csi_in>;
> +				clock-lanes = <0>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
>  };
>  
>  &i2c4 {
> @@ -141,6 +179,18 @@ pca6416_1: gpio@21 {
>  	};
>  };
>  
> +&mipi_csi {
> +	status = "okay";
> +	ports {
> +		port@0 {
> +			imx8mm_mipi_csi_in: endpoint {
> +				remote-endpoint = <&ov5640_to_mipi_csi2>;
> +				data-lanes = <1 2>;
> +			};
> +		};
> +	};
> +};
> +
>  &sai3 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_sai3>;
> @@ -209,6 +259,14 @@ MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28	0x41
>  		>;
>  	};
>  
> +	pinctrl_ov5640: ov5640grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
> +			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
> +			MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1	0x59
> +		>;
> +	};
> +
>  	pinctrl_pcal6414: pcal6414-gpiogrp {
>  		fsl,pins = <
>  			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19

-- 
Regards,

Laurent Pinchart