Re: [PATCH v2 4/8] dt-bindings: pinctrl: Add Nuvoton WPCM450

From: Rob Herring
Date: Fri Dec 10 2021 - 10:18:08 EST

On Tue, Dec 07, 2021 at 10:08:19PM +0100, Jonathan Neuschäfer wrote:
> This binding is heavily based on the one for NPCM7xx, because the
> hardware is similar. There are some notable differences, however:
>
> - The addresses of GPIO banks are not physical addresses but simple
> indices (0 to 7), because the GPIO registers are not laid out in
> convenient blocks.
> - Pinmux settings can explicitly specify that the GPIO mode is used.
>
> Certain pins support blink patterns in hardware. This is currently not
> modelled in the DT binding.
>
> Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@xxxxxxx>
>
>
> ---
> v2:
> - Move GPIO into subnodes
> - Improve use of quotes
> - Remove unnecessary minItems/maxItems lines
> - Remove "phandle: true"
> - Use separate prefixes for pinmux and pincfg nodes
> - Add nuvoton,interrupt-map property
> - Make it possible to set pinmux to GPIO explicitly
>
> v1:
> - https://lore.kernel.org/lkml/20210602120329.2444672-5-j.neuschaefer@xxxxxxx/
> ---
> .../pinctrl/nuvoton,wpcm450-pinctrl.yaml | 190 ++++++++++++++++++
> 1 file changed, 190 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
> new file mode 100644
> index 0000000000000..2b783597794d7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
> @@ -0,0 +1,190 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/nuvoton,wpcm450-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Nuvoton WPCM450 pin control and GPIO
> +
> +maintainers:
> + - Jonathan Neuschäfer <j.neuschaefer@xxxxxxx>
> +
> +properties:
> + compatible:
> + const: nuvoton,wpcm450-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> +patternProperties:
> + # There are three kinds of subnodes:
> + # 1. a GPIO controller node for each GPIO bank
> + # 2. a pinmux node configures pin muxing for a group of pins (e.g. rmii2)
> + # 3. a pinconf node configures properties of a single pin
> +
> + "^gpio@.*$":
> + if:

Not necessary because you can't have a property with '@' in it.

> + type: object
> + then:
> + description:
> + Eight GPIO banks (gpio@0 to gpio@7), that each contain between 14 and 18
> + GPIOs. Some GPIOs support interrupts.
> +
> + allOf:
> + - $ref: pinmux-node.yaml#
> +
> + properties:
> + reg:
> + description: GPIO bank number (0-7)
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 2
> +
> + interrupts:
> + maxItems: 4

Need to define what each interrupt is.

> +
> + nuvoton,interrupt-map:

Reusing 'interrupt-map' with a different definition bothers me...

> + description:
> + This property defines which bits in the interrupt registers
> + correspond to which GPIOs.
> + $ref: /schemas/types.yaml#/definitions/uint32-array
> + items:
> + - description: First interrupt bit
> + - description: Number of interrupt bits
> + - description: First GPIO associated with an interrupt
> +
> + required:
> + - reg
> + - gpio-controller
> + - '#gpio-cells'
> +
> + "^mux_.*$":

Use '-' rather than '_' and the '.*' is not necessary.

"^mux-"

> + if:

Don't need this.

> + type: object
> + then:
> + allOf:
> + - $ref: pinmux-node.yaml#
> + properties:
> + groups:
> + description:
> + One or more groups of pins to mux to a certain function
> + items:
> + enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp,
> + hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo,
> + clko, smi, uinc, gspi, mben, xcs2, xcs1, sdio, sspi, fi0,
> + fi1, fi2, fi3, fi4, fi5, fi6, fi7, fi8, fi9, fi10, fi11,
> + fi12, fi13, fi14, fi15, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5,
> + pwm6, pwm7, hg0, hg1, hg2, hg3, hg4, hg5, hg6, hg7 ]
> + function:
> + description:
> + The function that a group of pins is muxed to
> + enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp,
> + hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo0,
> + dvo1, dvo2, dvo3, dvo4, dvo5, dvo6, dvo7, clko, smi, uinc,
> + gspi, mben, xcs2, xcs1, sdio, sspi, fi0, fi1, fi2, fi3, fi4,
> + fi5, fi6, fi7, fi8, fi9, fi10, fi11, fi12, fi13, fi14, fi15,
> + pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, hg0, hg1,
> + hg2, hg3, hg4, hg5, hg6, hg7, gpio ]
> +
> + dependencies:
> + groups: [ function ]
> + function: [ groups ]
> +
> + additionalProperties: false
> +
> + "^cfg_.*$":
> + if:

Same comments here

> + type: object
> + then:
> + allOf:
> + - $ref: pincfg-node.yaml#
> + properties:
> + pins:
> + description:
> + A list of pins to configure in certain ways, such as enabling
> + debouncing
> + items:
> + enum: [ gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7,
> + gpio8, gpio9, gpio10, gpio11, gpio12, gpio13, gpio14,
> + gpio15, gpio16, gpio17, gpio18, gpio19, gpio20, gpio21,
> + gpio22, gpio23, gpio24, gpio25, gpio26, gpio27, gpio28,
> + gpio29, gpio30, gpio31, gpio32, gpio33, gpio34, gpio35,
> + gpio36, gpio37, gpio38, gpio39, gpio40, gpio41, gpio42,
> + gpio43, gpio44, gpio45, gpio46, gpio47, gpio48, gpio49,
> + gpio50, gpio51, gpio52, gpio53, gpio54, gpio55, gpio56,
> + gpio57, gpio58, gpio59, gpio60, gpio61, gpio62, gpio63,
> + gpio64, gpio65, gpio66, gpio67, gpio68, gpio69, gpio70,
> + gpio71, gpio72, gpio73, gpio74, gpio75, gpio76, gpio77,
> + gpio78, gpio79, gpio80, gpio81, gpio82, gpio83, gpio84,
> + gpio85, gpio86, gpio87, gpio88, gpio89, gpio90, gpio91,
> + gpio92, gpio93, gpio94, gpio95, gpio96, gpio97, gpio98,
> + gpio99, gpio100, gpio101, gpio102, gpio103, gpio104,
> + gpio105, gpio106, gpio107, gpio108, gpio109, gpio110,
> + gpio111, gpio112, gpio113, gpio114, gpio115, gpio116,
> + gpio117, gpio118, gpio119, gpio120, gpio121, gpio122,
> + gpio123, gpio124, gpio125, gpio126, gpio127 ]

pattern: '^gpio1?[0-9]{1,2}$'

Feel free to tweak it more to limit to 127 if you want.

> +
> + input-debounce: true
> +
> + additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/gpio/gpio.h>
> + pinctrl: pinctrl@b8003000 {
> + compatible = "nuvoton,wpcm450-pinctrl";
> + reg = <0xb8003000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + gpio0: gpio@0 {
> + reg = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <2 IRQ_TYPE_LEVEL_HIGH
> + 3 IRQ_TYPE_LEVEL_HIGH
> + 4 IRQ_TYPE_LEVEL_HIGH>;
> + nuvoton,interrupt-map = <0 16 0>;

Based on the example, you don't need this as it is 1:1.

> + };
> +
> + mux_rmii2 {
> + groups = "rmii2";
> + function = "rmii2";
> + };
> +
> + pinmux_uid: mux_uid {
> + groups = "gspi", "sspi";
> + function = "gpio";
> + };
> +
> + pinctrl_uid: cfg_uid {
> + pins = "gpio14";
> + input-debounce = <1>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uid>, <&pinmux_uid>;
> +
> + uid {
> + label = "UID";
> + linux,code = <102>;
> + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> + };
> + };
> --
> 2.30.2
>
>