Re: [PATCH 4/4] dt-bindings: mfd: maxim,max77693: convert to dtschema

[Krzysztof Kozlowski]

On 10/01/2022 20:10, Rob Herring wrote:
> On Tue, Dec 28, 2021 at 05:39:30PM +0100, Krzysztof Kozlowski wrote:
>> Convert the MFD part of Maxim MAX77693 MUIC to DT schema format.  The
>> example DTS was copied from existing DTS (exynos4412-midas.dtsi), so
>> keep the license as GPL-2.0-only.
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx>
>> ---
>>  .../devicetree/bindings/mfd/max77693.txt      | 194 ------------------
>>  .../bindings/mfd/maxim,max77693.yaml          | 139 +++++++++++++
>>  MAINTAINERS                                   |   2 +-
>>  3 files changed, 140 insertions(+), 195 deletions(-)
>>  delete mode 100644 Documentation/devicetree/bindings/mfd/max77693.txt
>>  create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
>> deleted file mode 100644
>> index 1032df14498b..000000000000
>> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
>> +++ /dev/null
>> @@ -1,194 +0,0 @@
>> -Maxim MAX77693 multi-function device
>> -
>> -MAX77693 is a Multifunction device with the following submodules:
>> -- PMIC,
>> -- CHARGER,
>> -- LED,
>> -- MUIC,
>> -- HAPTIC
>> -
>> -It is interfaced to host controller using i2c.
>> -This document describes the bindings for the mfd device.
>> -
>> -Required properties:
>> -- compatible : Must be "maxim,max77693".
>> -- reg : Specifies the i2c slave address of PMIC block.
>> -- interrupts : This i2c device has an IRQ line connected to the main SoC.
>> -
>> -Optional properties:
>> -- regulators : The regulators of max77693 have to be instantiated under subnode
>> -  named "regulators" using the following format.
>> -
>> -	regulators {
>> -		regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
>> -		standard regulator constraints[*].
>> -	};
>> -
>> -	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
>> -
>> -- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
>> -  users with tactile feedback. PWM period and duty-cycle are varied in
>> -  order to provide the appropriate level of feedback.
>> -
>> - Required properties:
>> -	- compatible : Must be "maxim,max77693-haptic"
>> -	- haptic-supply : power supply for the haptic motor
>> -	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
>> -	- pwms : phandle to the physical PWM(Pulse Width Modulation) device.
>> -	 PWM properties should be named "pwms". And number of cell is different
>> -	 for each pwm device.
>> -	 To get more information, please refer to documentation.
>> -	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
>> -
>> -- charger : Node configuring the charger driver.
>> -  If present, required properties:
>> -  - compatible : Must be "maxim,max77693-charger".
>> -
>> -  Optional properties (if not set, defaults will be used):
>> -  - maxim,constant-microvolt : Battery constant voltage in uV. The charger
>> -    will operate in fast charge constant current mode till battery voltage
>> -    reaches this level. Then the charger will switch to fast charge constant
>> -    voltage mode. Also vsys (system voltage) will be set to this value when
>> -    DC power is supplied but charger is not enabled.
>> -    Valid values: 3650000 - 4400000, step by 25000 (rounded down)
>> -    Default: 4200000
>> -
>> -  - maxim,min-system-microvolt : Minimal system voltage in uV.
>> -    Valid values: 3000000 - 3700000, step by 100000 (rounded down)
>> -    Default: 3600000
>> -
>> -  - maxim,thermal-regulation-celsius : Temperature in Celsius for entering
>> -    high temperature charging mode. If die temperature exceeds this value
>> -    the charging current will be reduced by 105 mA/Celsius.
>> -    Valid values: 70, 85, 100, 115
>> -    Default: 100
>> -
>> -  - maxim,battery-overcurrent-microamp : Overcurrent protection threshold
>> -    in uA (current from battery to system).
>> -    Valid values: 2000000 - 3500000, step by 250000 (rounded down)
>> -    Default: 3500000
>> -
>> -  - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for
>> -    triggering input voltage regulation loop. If input voltage decreases
>> -    below this value, the input current will be reduced to reach the
>> -    threshold voltage.
>> -    Valid values: 4300000, 4700000, 4800000, 4900000
>> -    Default: 4300000
>> -
>> -- led : the LED submodule device node
>> -
>> -There are two LED outputs available - FLED1 and FLED2. Each of them can
>> -control a separate LED or they can be connected together to double
>> -the maximum current for a single connected LED. One LED is represented
>> -by one child node.
>> -
>> -Required properties:
>> -- compatible : Must be "maxim,max77693-led".
>> -
>> -Optional properties:
>> -- maxim,boost-mode :
>> -	In boost mode the device can produce up to 1.2A of total current
>> -	on both outputs. The maximum current on each output is reduced
>> -	to 625mA then. If not enabled explicitly, boost setting defaults to
>> -	LEDS_BOOST_FIXED in case both current sources are used.
>> -	Possible values:
>> -		LEDS_BOOST_OFF (0) - no boost,
>> -		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
>> -		LEDS_BOOST_FIXED (2) - fixed mode.
>> -- maxim,boost-mvout : Output voltage of the boost module in millivolts.
>> -	Valid values: 3300 - 5500, step by 25 (rounded down)
>> -	Default: 3300
>> -- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
>> -	if chip estimates that system voltage could drop below this level due
>> -	to flash power consumption.
>> -	Valid values: 2400 - 3400, step by 33 (rounded down)
>> -	Default: 2400
>> -
>> -Required properties for the LED child node:
>> -- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
>> -		device current output identifiers: 0 - FLED1, 1 - FLED2
>> -- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
>> -	Valid values for a LED connected to one FLED output:
>> -		15625 - 250000, step by 15625 (rounded down)
>> -	Valid values for a LED connected to both FLED outputs:
>> -		15625 - 500000, step by 15625 (rounded down)
>> -- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
>> -	Valid values for a single LED connected to one FLED output
>> -	(boost mode must be turned off):
>> -		15625 - 1000000, step by 15625 (rounded down)
>> -	Valid values for a single LED connected to both FLED outputs:
>> -		15625 - 1250000, step by 15625 (rounded down)
>> -	Valid values for two LEDs case:
>> -		15625 - 625000, step by 15625 (rounded down)
>> -- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
>> -	Valid values: 62500 - 1000000, step by 62500 (rounded down)
>> -
>> -Optional properties for the LED child node:
>> -- label : see Documentation/devicetree/bindings/leds/common.txt
>> -
>> -Optional nodes:
>> -- max77693-muic :
>> -	Node used only by extcon consumers.
>> -	Required properties:
>> -		- compatible : "maxim,max77693-muic"
>> -
>> -Example:
>> -#include <dt-bindings/leds/common.h>
>> -
>> -	max77693@66 {
>> -		compatible = "maxim,max77693";
>> -		reg = <0x66>;
>> -		interrupt-parent = <&gpx1>;
>> -		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
>> -
>> -		regulators {
>> -			esafeout@1 {
>> -				regulator-compatible = "ESAFEOUT1";
>> -				regulator-name = "ESAFEOUT1";
>> -				regulator-boot-on;
>> -			};
>> -			esafeout@2 {
>> -				regulator-compatible = "ESAFEOUT2";
>> -				regulator-name = "ESAFEOUT2";
>> -				};
>> -			charger@0 {
>> -				regulator-compatible = "CHARGER";
>> -				regulator-name = "CHARGER";
>> -				regulator-min-microamp = <60000>;
>> -				regulator-max-microamp = <2580000>;
>> -					regulator-boot-on;
>> -			};
>> -		};
>> -
>> -		haptic {
>> -			compatible = "maxim,max77693-haptic";
>> -			haptic-supply = <&haptic_supply>;
>> -			pwms = <&pwm 0 40000 0>;
>> -			pwm-names = "haptic";
>> -		};
>> -
>> -		charger {
>> -			compatible = "maxim,max77693-charger";
>> -
>> -			maxim,constant-microvolt = <4200000>;
>> -			maxim,min-system-microvolt = <3600000>;
>> -			maxim,thermal-regulation-celsius = <75>;
>> -			maxim,battery-overcurrent-microamp = <3000000>;
>> -			maxim,charge-input-threshold-microvolt = <4300000>;
>> -		};
>> -
>> -		led {
>> -			compatible = "maxim,max77693-led";
>> -			maxim,boost-mode = <LEDS_BOOST_FIXED>;
>> -			maxim,boost-mvout = <5000>;
>> -			maxim,mvsys-min = <2400>;
>> -
>> -			camera_flash: flash-led {
>> -				label = "max77693-flash";
>> -				led-sources = <0>, <1>;
>> -				led-max-microamp = <500000>;
>> -				flash-max-microamp = <1250000>;
>> -				flash-max-timeout-us = <1000000>;
>> -			};
>> -		};
>> -	};
>> diff --git a/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml b/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>> new file mode 100644
>> index 000000000000..bc9c90bd4ff9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>> @@ -0,0 +1,139 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mfd/maxim,max77693.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Maxim MAX77693 MicroUSB and Companion Power Management IC
>> +
>> +maintainers:
>> +  - Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> +  - Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx>
>> +
>> +description: |
>> +  This is a part of device tree bindings for Maxim MAX77693 MicroUSB
>> +  Integrated Circuit (MUIC).
>> +
>> +  The Maxim MAX77693 is a MicroUSB and Companion Power Management IC which
>> +  includes voltage current regulators, charger, LED/flash, haptic motor driver
>> +  and MicroUSB management IC.
>> +
>> +properties:
>> +  compatible:
>> +    const: maxim,max77693
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  charger:
>> +    $ref: ../power/supply/maxim,max77693.yaml
> 
> /schemas/power/supply/...
> 
>> +
>> +  led:
>> +    $ref: ../leds/maxim,max77693.yaml
> 
> ditto
> 
>> +
>> +  max77693-muic:
>> +    type: object
> 
>        additionalProperties: false
> 
>> +    properties:
>> +      compatible:
>> +        const: maxim,max77693-muic
>> +
>> +    required:
>> +      - compatible
>> +
>> +  motor-driver:
>> +    type: object
> 
>        additionalProperties: false
> 

Thanks, fixed all issues.


Best regards,
Krzysztof