[PATCH v4 1/2] arm: dts: sun7i: Add A20-Marsboard

[Conley Lee]

The Marsboard A20 is a A20 based SBC with 1G RAM, 8G Flash, micro SD
card slot , SATA socketm 10/100 ethernet, HDMI port, 4 USB2.0 ports, 2
USB2.0 OTG, USB WIFI(RTL8188EU) with antenna.

Signed-off-by: Conley Lee <conleylee@xxxxxxxxxxx>
---
Change since v1.
  - Spearate biddings and dts as two patches.
  - use SPDX tag

Change since v2.
  - reformat patch
  - dual-license with GPL and MIT
  - rename dts filename to sun7i-a20-haoyu-marsboard.dts
Change since v3.
  - reformat patch
  - order dtb alphabetically
  - add gmac_txerr node and remove gmac_mii_pins node in
    sun7i-a20-marsboard.dts
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/sun7i-a20-haoyu-marsboard.dts    | 183 ++++++++++++++++++
 2 files changed, 184 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..1850ff7c9006 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1213,6 +1213,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-bananapro.dtb \
 	sun7i-a20-cubieboard2.dtb \
 	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-itead-ibox.dtb \
 	sun7i-a20-i12-tvbox.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
new file mode 100644
index 000000000000..056dbc415de7
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Conley Lee
+ * Conley Lee <conleylee@xxxxxxxxxxx>
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "HAOYU Electronics Marsboard A20";
+	compatible = "haoyu,a20-marsboard", "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
+	phy-handle = <&phy0>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	gmac_txerr: gmac-txerr-pin {
+		pins = "PA17";
+		function = "gmac";
+	};
+};
+
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1450000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
-- 
2.31.1