[PATCH v2 2/9] regulator: rpi-panel: Handle I2C errors/timing to the Atmel

[Detlev Casanova]

From: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>

The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.

Increase delays appropriately, and retry should I2C errors be
reported.

Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
---
 .../regulator/rpi-panel-attiny-regulator.c    | 56 +++++++++++++++----
 1 file changed, 46 insertions(+), 10 deletions(-)

diff --git a/drivers/regulator/rpi-panel-attiny-regulator.c b/drivers/regulator/rpi-panel-attiny-regulator.c
index 370b9ae363dd..00fb69efcfa2 100644
--- a/drivers/regulator/rpi-panel-attiny-regulator.c
+++ b/drivers/regulator/rpi-panel-attiny-regulator.c
@@ -37,11 +37,24 @@ static const struct regmap_config attiny_regmap_config = {
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
 	unsigned int data;
+	int ret, i;
 
 	regmap_write(rdev->regmap, REG_POWERON, 1);
+	msleep(80);
+
 	/* Wait for nPWRDWN to go low to indicate poweron is done. */
-	regmap_read_poll_timeout(rdev->regmap, REG_PORTB, data,
-					data & BIT(0), 10, 1000000);
+	for (i = 0; i < 20; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret) {
+			if (data & BIT(0))
+				break;
+		}
+		usleep_range(10000, 12000);
+	}
+	usleep_range(10000, 12000);
+
+	if (ret)
+		pr_err("%s: regmap_read_poll_timeout failed %d\n", __func__, ret);
 
 	/* Default to the same orientation as the closed source
 	 * firmware used for the panel.  Runtime rotation
@@ -57,23 +70,34 @@ static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 {
 	regmap_write(rdev->regmap, REG_PWM, 0);
 	regmap_write(rdev->regmap, REG_POWERON, 0);
-	udelay(1);
+	msleep(30);
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
 	unsigned int data;
-	int ret;
+	int ret, i;
 
-	ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
 	if (ret < 0)
 		return ret;
 
 	if (!(data & BIT(0)))
 		return 0;
 
-	ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
+
 	if (ret < 0)
 		return ret;
 
@@ -103,20 +127,32 @@ static int attiny_update_status(struct backlight_device *bl)
 {
 	struct regmap *regmap = bl_get_data(bl);
 	int brightness = bl->props.brightness;
+	int ret, i;
 
 	if (bl->props.power != FB_BLANK_UNBLANK ||
 	    bl->props.fb_blank != FB_BLANK_UNBLANK)
 		brightness = 0;
 
-	return regmap_write(regmap, REG_PWM, brightness);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_write(regmap, REG_PWM, brightness);
+		if (!ret)
+			break;
+	}
+
+	return ret;
 }
 
 static int attiny_get_brightness(struct backlight_device *bl)
 {
 	struct regmap *regmap = bl_get_data(bl);
-	int ret, brightness;
+	int ret, brightness, i;
+
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(regmap, REG_PWM, &brightness);
+		if (!ret)
+			break;
+	}
 
-	ret = regmap_read(regmap, REG_PWM, &brightness);
 	if (ret)
 		return ret;
 
@@ -166,7 +202,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	}
 
 	regmap_write(regmap, REG_POWERON, 0);
-	mdelay(1);
+	msleep(30);
 
 	config.dev = &i2c->dev;
 	config.regmap = regmap;
-- 
2.34.1