Re: [PATCH v2 11/11] ARM: dts: armada-385.dtsi: Add definitions for PCIe legacy INTx interrupts

[Gregory CLEMENT]

Hello,

> On Monday 14 February 2022 16:07:13 Gregory CLEMENT wrote:
>> Hello Pali,
>> 
>> > With this change legacy INTA, INTB, INTC and INTD interrupts are reported
>> > separately and not mixed into one Linux virq source anymore.
>> >
>> > Signed-off-by: Pali Rohár <pali@xxxxxxxxxx>
>> > ---
>> >  arch/arm/boot/dts/armada-385.dtsi | 52 ++++++++++++++++++++++++++-----
>> 
>> Is there any reason for not doing the same change in armada-380.dtsi ?
>
> I do not have A380 HW, so I did this change only for A385 which I have
> tested.

OK fair enough.

So you can add my
Acked-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx>

Moreover to keep biscetability  this patch should be merged after the
support in the driver. So the easier is to let merge it through the PCI
subsystem with the other patches from this series. I do not think there
will be any other changes in this file so there won't be any merge
conflicts.

Thanks,

Grégory


>
>> Grégory
>> 
>> >  1 file changed, 44 insertions(+), 8 deletions(-)
>> >
>> > diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi
>> > index f0022d10c715..83392b92dae2 100644
>> > --- a/arch/arm/boot/dts/armada-385.dtsi
>> > +++ b/arch/arm/boot/dts/armada-385.dtsi
>> > @@ -69,16 +69,25 @@
>> >  				reg = <0x0800 0 0 0 0>;
>> >  				#address-cells = <3>;
>> >  				#size-cells = <2>;
>> > +				interrupt-names = "intx";
>> > +				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
>> >  				#interrupt-cells = <1>;
>> >  				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
>> >  					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
>> >  				bus-range = <0x00 0xff>;
>> > -				interrupt-map-mask = <0 0 0 0>;
>> > -				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
>> > +				interrupt-map-mask = <0 0 0 7>;
>> > +				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
>> > +						<0 0 0 2 &pcie1_intc 1>,
>> > +						<0 0 0 3 &pcie1_intc 2>,
>> > +						<0 0 0 4 &pcie1_intc 3>;
>> >  				marvell,pcie-port = <0>;
>> >  				marvell,pcie-lane = <0>;
>> >  				clocks = <&gateclk 8>;
>> >  				status = "disabled";
>> > +				pcie1_intc: interrupt-controller {
>> > +					interrupt-controller;
>> > +					#interrupt-cells = <1>;
>> > +				};
>> >  			};
>> >  
>> >  			/* x1 port */
>> > @@ -88,16 +97,25 @@
>> >  				reg = <0x1000 0 0 0 0>;
>> >  				#address-cells = <3>;
>> >  				#size-cells = <2>;
>> > +				interrupt-names = "intx";
>> > +				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> >  				#interrupt-cells = <1>;
>> >  				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
>> >  					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
>> >  				bus-range = <0x00 0xff>;
>> > -				interrupt-map-mask = <0 0 0 0>;
>> > -				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> > +				interrupt-map-mask = <0 0 0 7>;
>> > +				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
>> > +						<0 0 0 2 &pcie2_intc 1>,
>> > +						<0 0 0 3 &pcie2_intc 2>,
>> > +						<0 0 0 4 &pcie2_intc 3>;
>> >  				marvell,pcie-port = <1>;
>> >  				marvell,pcie-lane = <0>;
>> >  				clocks = <&gateclk 5>;
>> >  				status = "disabled";
>> > +				pcie2_intc: interrupt-controller {
>> > +					interrupt-controller;
>> > +					#interrupt-cells = <1>;
>> > +				};
>> >  			};
>> >  
>> >  			/* x1 port */
>> > @@ -107,16 +125,25 @@
>> >  				reg = <0x1800 0 0 0 0>;
>> >  				#address-cells = <3>;
>> >  				#size-cells = <2>;
>> > +				interrupt-names = "intx";
>> > +				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
>> >  				#interrupt-cells = <1>;
>> >  				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
>> >  					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
>> >  				bus-range = <0x00 0xff>;
>> > -				interrupt-map-mask = <0 0 0 0>;
>> > -				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
>> > +				interrupt-map-mask = <0 0 0 7>;
>> > +				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
>> > +						<0 0 0 2 &pcie3_intc 1>,
>> > +						<0 0 0 3 &pcie3_intc 2>,
>> > +						<0 0 0 4 &pcie3_intc 3>;
>> >  				marvell,pcie-port = <2>;
>> >  				marvell,pcie-lane = <0>;
>> >  				clocks = <&gateclk 6>;
>> >  				status = "disabled";
>> > +				pcie3_intc: interrupt-controller {
>> > +					interrupt-controller;
>> > +					#interrupt-cells = <1>;
>> > +				};
>> >  			};
>> >  
>> >  			/*
>> > @@ -129,16 +156,25 @@
>> >  				reg = <0x2000 0 0 0 0>;
>> >  				#address-cells = <3>;
>> >  				#size-cells = <2>;
>> > +				interrupt-names = "intx";
>> > +				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
>> >  				#interrupt-cells = <1>;
>> >  				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
>> >  					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
>> >  				bus-range = <0x00 0xff>;
>> > -				interrupt-map-mask = <0 0 0 0>;
>> > -				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
>> > +				interrupt-map-mask = <0 0 0 7>;
>> > +				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
>> > +						<0 0 0 2 &pcie4_intc 1>,
>> > +						<0 0 0 3 &pcie4_intc 2>,
>> > +						<0 0 0 4 &pcie4_intc 3>;
>> >  				marvell,pcie-port = <3>;
>> >  				marvell,pcie-lane = <0>;
>> >  				clocks = <&gateclk 7>;
>> >  				status = "disabled";
>> > +				pcie4_intc: interrupt-controller {
>> > +					interrupt-controller;
>> > +					#interrupt-cells = <1>;
>> > +				};
>> >  			};
>> >  		};
>> >  	};
>> > -- 
>> > 2.20.1
>> >
>> 
>> -- 
>> Gregory Clement, Bootlin
>> Embedded Linux and Kernel engineering
>> http://bootlin.com

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com