Re: [PATCH 2/3] spi: tegra210-quad: Add wait polling support

[Jon Hunter]

On 17/03/2022 09:02, Krishna Yarlagadda wrote:
> > -----Original Message-----
> > From: Jonathan Hunter <jonathanh@xxxxxxxxxx>
> > Sent: 17 March 2022 14:25
> > To: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>; broonie@xxxxxxxxxx; thierry.reding@xxxxxxxxx; linux-spi@xxxxxxxxxxxxxxx; linux-
> > tegra@xxxxxxxxxxxxxxx; Ashish Singhal <ashishsingha@xxxxxxxxxx>
> > Cc: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>; Laxman Dewangan <ldewangan@xxxxxxxxxx>; robh+dt@xxxxxxxxxx;
> > devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> > Subject: Re: [PATCH 2/3] spi: tegra210-quad: Add wait polling support
> >
> >
> > On 17/03/2022 01:20, Krishna Yarlagadda wrote:
> > > Controller can poll for wait state inserted by TPM device and
> > > handle it.
> > >
> > > Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
> > > ---
> > >    drivers/spi/spi-tegra210-quad.c | 31 +++++++++++++++++++++++++++++++
> > >    1 file changed, 31 insertions(+)
> > >
> > > diff --git a/drivers/spi/spi-tegra210-quad.c b/drivers/spi/spi-tegra210-quad.c
> > > index a2e225e8f7f0..ecf171bfcdce 100644
> > > --- a/drivers/spi/spi-tegra210-quad.c
> > > +++ b/drivers/spi/spi-tegra210-quad.c
> > > @@ -142,6 +142,7 @@
> > >
> > >    #define QSPI_GLOBAL_CONFIG			0X1a4
> > >    #define QSPI_CMB_SEQ_EN				BIT(0)
> > > +#define QSPI_TPM_WAIT_POLL_EN			BIT(1)
> > >
> > >    #define QSPI_CMB_SEQ_ADDR			0x1a8
> > >    #define QSPI_ADDRESS_VALUE_SET(X)		(((x) & 0xFFFF) << 0)
> > > @@ -165,11 +166,13 @@ struct tegra_qspi_soc_data {
> > >    	bool has_dma;
> > >    	bool cmb_xfer_capable;
> > >    	bool cs_count;
> > > +	bool has_wait_polling;
> > >    };
> > >
> > >    struct tegra_qspi_client_data {
> > >    	int tx_clk_tap_delay;
> > >    	int rx_clk_tap_delay;
> > > +	bool wait_polling;
> > >    };
> > >
> > >    struct tegra_qspi {
> > > @@ -833,6 +836,11 @@ static u32 tegra_qspi_setup_transfer_one(struct spi_device *spi, struct spi_tran
> > >    		else
> > >    			command1 |= QSPI_CONTROL_MODE_0;
> > >
> > > +		if (tqspi->soc_data->cmb_xfer_capable)
> > > +			command1 &= ~QSPI_CS_SW_HW;
> > > +		else
> > > +			command1 |= QSPI_CS_SW_HW;
> > > +
> > >    		if (spi->mode & SPI_CS_HIGH)
> > >    			command1 |= QSPI_CS_SW_VAL;
> > >    		else
> > > @@ -917,6 +925,7 @@ static int tegra_qspi_start_transfer_one(struct spi_device *spi,
> > >
> > >    static struct tegra_qspi_client_data *tegra_qspi_parse_cdata_dt(struct spi_device *spi)
> > >    {
> > > +	struct tegra_qspi *tqspi = spi_master_get_devdata(spi->master);
> > >    	struct tegra_qspi_client_data *cdata;
> > >
> > >    	cdata = devm_kzalloc(&spi->dev, sizeof(*cdata), GFP_KERNEL);
> > > @@ -927,6 +936,11 @@ static struct tegra_qspi_client_data *tegra_qspi_parse_cdata_dt(struct spi_devic
> > >    				 &cdata->tx_clk_tap_delay);
> > >    	device_property_read_u32(&spi->dev, "nvidia,rx-clk-tap-delay",
> > >    				 &cdata->rx_clk_tap_delay);
> > > +	if (tqspi->soc_data->has_wait_polling)
> > > +		cdata->wait_polling = device_property_read_bool
> > > +					(&spi->dev,
> > > +					 "nvidia,wait-polling");
> > > +
> >
> >
> > This looks odd. Why do we need this device-tree property if it is
> > already specified in the SoC data?
> Soc data specifies chip is capable of wait-polling.
> Wait polling still has to be selected on slave devices that can support it.
> I will add one line description for the properties in next version.


I can't say I am familiar with this, but it seems that the ideal 
solution would be able to detect if this needs to be enabled depending 
on the device connected. Is that not possible?

Jon

--
nvpublic