Re: [PATCH 2/2] ARM: remove old MMU-less CPU support

[Alexandre TORGUE]

Hi Arnd

On 3/16/22 22:12, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@xxxxxxxx>
>
> The MMU-less ARM7 and ARM9 variants have been impossible to enable
> in mainline kernels for a long time, and the last such platform
> was removed in 2014.
>
> Remove the processor definitions for these, along with all associated
> configuration symbols.
>
> Suggested-by: Robin Murphy <robin.murphy@xxxxxxx>
> Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx>
> ---
> Given the timing of this submission, I would not expect this
> to make it into the 5.18 merge window. If I merge the other
> one of the two patches into the soc tree, I would suggest that
> we merge it for 5.19 through Russell's tree.
> ---
>   arch/arm/Kconfig                   |  10 +-
>   arch/arm/Kconfig-nommu             |  10 -
>   arch/arm/Makefile                  |   5 -
>   arch/arm/configs/lpc18xx_defconfig |   2 -
>   arch/arm/configs/stm32_defconfig   |   2 -
>   arch/arm/configs/vf610m4_defconfig |   2 -
>   arch/arm/include/asm/glue-cache.h  |  16 --
>   arch/arm/mm/Kconfig                | 106 +-------
>   arch/arm/mm/Makefile               |   5 -
>   arch/arm/mm/proc-arm740.S          | 147 ----------
>   arch/arm/mm/proc-arm7tdmi.S        | 110 --------
>   arch/arm/mm/proc-arm940.S          | 360 -------------------------
>   arch/arm/mm/proc-arm946.S          | 415 -----------------------------
>   arch/arm/mm/proc-arm9tdmi.S        |  91 -------
>   14 files changed, 8 insertions(+), 1273 deletions(-)
>   delete mode 100644 arch/arm/mm/proc-arm740.S
>   delete mode 100644 arch/arm/mm/proc-arm7tdmi.S
>   delete mode 100644 arch/arm/mm/proc-arm940.S
>   delete mode 100644 arch/arm/mm/proc-arm946.S
>   delete mode 100644 arch/arm/mm/proc-arm9tdmi.S

For STM32 part:
Acked-by: Alexandre TORGUE <alexandre.torgue@xxxxxxxxxxx>

Alex

> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index d184377ce2ae..2962778d5d12 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -515,17 +515,15 @@ config ARCH_MULTI_V4T
>   	bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
>   	depends on !ARCH_MULTI_V6_V7
>   	select ARCH_MULTI_V4_V5
> -	select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \
> -		CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
> -		CPU_ARM925T || CPU_ARM940T)
> +	select CPU_ARM920T if !(CPU_ARM720T || CPU_ARM922T || CPU_ARM925T)
>   
>   config ARCH_MULTI_V5
>   	bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
>   	depends on !ARCH_MULTI_V6_V7
>   	select ARCH_MULTI_V4_V5
> -	select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
> -		CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
> -		CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
> +	select CPU_ARM926T if !(CPU_ARM1020 || CPU_ARM1020E || CPU_ARM1022 || \
> +		CPU_ARM1026 || CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || \
> +		CPU_FEROCEON)
>   
>   config ARCH_MULTI_V4_V5
>   	bool
> diff --git a/arch/arm/Kconfig-nommu b/arch/arm/Kconfig-nommu
> index 36c80d3dd93f..add3e9b95078 100644
> --- a/arch/arm/Kconfig-nommu
> +++ b/arch/arm/Kconfig-nommu
> @@ -18,16 +18,6 @@ config DRAM_SIZE
>   	hex '(S)DRAM SIZE' if SET_MEM_PARAM
>   	default 0x00800000
>   
> -config FLASH_MEM_BASE
> -	hex 'FLASH Base Address' if SET_MEM_PARAM
> -	depends on CPU_ARM740T || CPU_ARM946E || CPU_ARM940T
> -	default 0x00400000
> -
> -config FLASH_SIZE
> -	hex 'FLASH Size' if SET_MEM_PARAM
> -	depends on CPU_ARM740T || CPU_ARM946E || CPU_ARM940T
> -	default 0x00400000
> -
>   config PROCESSOR_ID
>   	hex 'Hard wire the processor ID'
>   	default 0x00007700
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index a2391b8de5a5..8b34c4127c2e 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -77,12 +77,7 @@ arch-$(CONFIG_CPU_32v3)		=-D__LINUX_ARM_ARCH__=3 -march=armv3m
>   arch-y := $(arch-y)
>   
>   # This selects how we optimise for the processor.
> -tune-$(CONFIG_CPU_ARM7TDMI)	=-mtune=arm7tdmi
>   tune-$(CONFIG_CPU_ARM720T)	=-mtune=arm7tdmi
> -tune-$(CONFIG_CPU_ARM740T)	=-mtune=arm7tdmi
> -tune-$(CONFIG_CPU_ARM9TDMI)	=-mtune=arm9tdmi
> -tune-$(CONFIG_CPU_ARM940T)	=-mtune=arm9tdmi
> -tune-$(CONFIG_CPU_ARM946E)	=-mtune=arm9e
>   tune-$(CONFIG_CPU_ARM920T)	=-mtune=arm9tdmi
>   tune-$(CONFIG_CPU_ARM922T)	=-mtune=arm9tdmi
>   tune-$(CONFIG_CPU_ARM925T)	=-mtune=arm9tdmi
> diff --git a/arch/arm/configs/lpc18xx_defconfig b/arch/arm/configs/lpc18xx_defconfig
> index be882ea0eee4..9c8d153c4d6e 100644
> --- a/arch/arm/configs/lpc18xx_defconfig
> +++ b/arch/arm/configs/lpc18xx_defconfig
> @@ -22,8 +22,6 @@ CONFIG_ARCH_LPC18XX=y
>   CONFIG_SET_MEM_PARAM=y
>   CONFIG_DRAM_BASE=0x28000000
>   CONFIG_DRAM_SIZE=0x02000000
> -CONFIG_FLASH_MEM_BASE=0x1b000000
> -CONFIG_FLASH_SIZE=0x00080000
>   CONFIG_ZBOOT_ROM_TEXT=0x0
>   CONFIG_ZBOOT_ROM_BSS=0x0
>   CONFIG_ARM_APPENDED_DTB=y
> diff --git a/arch/arm/configs/stm32_defconfig b/arch/arm/configs/stm32_defconfig
> index 551db328009d..34cfcc945509 100644
> --- a/arch/arm/configs/stm32_defconfig
> +++ b/arch/arm/configs/stm32_defconfig
> @@ -19,8 +19,6 @@ CONFIG_ARCH_STM32=y
>   CONFIG_CPU_V7M_NUM_IRQ=240
>   CONFIG_SET_MEM_PARAM=y
>   CONFIG_DRAM_BASE=0x90000000
> -CONFIG_FLASH_MEM_BASE=0x08000000
> -CONFIG_FLASH_SIZE=0x00200000
>   CONFIG_PREEMPT=y
>   # CONFIG_ATAGS is not set
>   CONFIG_ZBOOT_ROM_TEXT=0x0
> diff --git a/arch/arm/configs/vf610m4_defconfig b/arch/arm/configs/vf610m4_defconfig
> index a89f035c3b01..28cb4649656e 100644
> --- a/arch/arm/configs/vf610m4_defconfig
> +++ b/arch/arm/configs/vf610m4_defconfig
> @@ -11,8 +11,6 @@ CONFIG_ARCH_MXC=y
>   CONFIG_SOC_VF610=y
>   CONFIG_SET_MEM_PARAM=y
>   CONFIG_DRAM_BASE=0x8c000000
> -CONFIG_FLASH_MEM_BASE=0x8f000000
> -CONFIG_FLASH_SIZE=0x01000000
>   CONFIG_CMDLINE="console=/dev/ttyLP2"
>   CONFIG_XIP_KERNEL=y
>   CONFIG_XIP_PHYS_ADDR=0x0f000080
> diff --git a/arch/arm/include/asm/glue-cache.h b/arch/arm/include/asm/glue-cache.h
> index 724f8dac1e5b..07b7dc2ae0f5 100644
> --- a/arch/arm/include/asm/glue-cache.h
> +++ b/arch/arm/include/asm/glue-cache.h
> @@ -46,22 +46,6 @@
>   # endif
>   #endif
>   
> -#if defined(CONFIG_CPU_ARM940T)
> -# ifdef _CACHE
> -#  define MULTI_CACHE 1
> -# else
> -#  define _CACHE arm940
> -# endif
> -#endif
> -
> -#if defined(CONFIG_CPU_ARM946E)
> -# ifdef _CACHE
> -#  define MULTI_CACHE 1
> -# else
> -#  define _CACHE arm946
> -# endif
> -#endif
> -
>   #if defined(CONFIG_CPU_CACHE_V4WB)
>   # ifdef _CACHE
>   #  define MULTI_CACHE 1
> diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
> index d30ee26ccc87..8cbedef19188 100644
> --- a/arch/arm/mm/Kconfig
> +++ b/arch/arm/mm/Kconfig
> @@ -5,21 +5,6 @@ comment "Processor Type"
>   # which CPUs we support in the kernel image, and the compiler instruction
>   # optimiser behaviour.
>   
> -# ARM7TDMI
> -config CPU_ARM7TDMI
> -	bool
> -	depends on !MMU
> -	select CPU_32v4T
> -	select CPU_ABRT_LV4T
> -	select CPU_CACHE_V4
> -	select CPU_PABRT_LEGACY
> -	help
> -	  A 32-bit RISC microprocessor based on the ARM7 processor core
> -	  which has no memory control unit and cache.
> -
> -	  Say Y if you want support for the ARM7TDMI processor.
> -	  Otherwise, say N.
> -
>   # ARM720T
>   config CPU_ARM720T
>   	bool
> @@ -39,39 +24,6 @@ config CPU_ARM720T
>   	  Say Y if you want support for the ARM720T processor.
>   	  Otherwise, say N.
>   
> -# ARM740T
> -config CPU_ARM740T
> -	bool
> -	depends on !MMU
> -	select CPU_32v4T
> -	select CPU_ABRT_LV4T
> -	select CPU_CACHE_V4
> -	select CPU_CP15_MPU
> -	select CPU_PABRT_LEGACY
> -	select CPU_THUMB_CAPABLE
> -	help
> -	  A 32-bit RISC processor with 8KB cache or 4KB variants,
> -	  write buffer and MPU(Protection Unit) built around
> -	  an ARM7TDMI core.
> -
> -	  Say Y if you want support for the ARM740T processor.
> -	  Otherwise, say N.
> -
> -# ARM9TDMI
> -config CPU_ARM9TDMI
> -	bool
> -	depends on !MMU
> -	select CPU_32v4T
> -	select CPU_ABRT_NOMMU
> -	select CPU_CACHE_V4
> -	select CPU_PABRT_LEGACY
> -	help
> -	  A 32-bit RISC microprocessor based on the ARM9 processor core
> -	  which has no memory control unit and cache.
> -
> -	  Say Y if you want support for the ARM9TDMI processor.
> -	  Otherwise, say N.
> -
>   # ARM920T
>   config CPU_ARM920T
>   	bool
> @@ -168,43 +120,6 @@ config CPU_FA526
>   	  Say Y if you want support for the FA526 processor.
>   	  Otherwise, say N.
>   
> -# ARM940T
> -config CPU_ARM940T
> -	bool
> -	depends on !MMU
> -	select CPU_32v4T
> -	select CPU_ABRT_NOMMU
> -	select CPU_CACHE_VIVT
> -	select CPU_CP15_MPU
> -	select CPU_PABRT_LEGACY
> -	select CPU_THUMB_CAPABLE
> -	help
> -	  ARM940T is a member of the ARM9TDMI family of general-
> -	  purpose microprocessors with MPU and separate 4KB
> -	  instruction and 4KB data cases, each with a 4-word line
> -	  length.
> -
> -	  Say Y if you want support for the ARM940T processor.
> -	  Otherwise, say N.
> -
> -# ARM946E-S
> -config CPU_ARM946E
> -	bool
> -	depends on !MMU
> -	select CPU_32v5
> -	select CPU_ABRT_NOMMU
> -	select CPU_CACHE_VIVT
> -	select CPU_CP15_MPU
> -	select CPU_PABRT_LEGACY
> -	select CPU_THUMB_CAPABLE
> -	help
> -	  ARM946E-S is a member of the ARM9E-S family of high-
> -	  performance, 32-bit system-on-chip processor solutions.
> -	  The TCM and ARMv5TE 32-bit instruction set is supported.
> -
> -	  Say Y if you want support for the ARM946E-S processor.
> -	  Otherwise, say N.
> -
>   # ARM1020 - needs validating
>   config CPU_ARM1020
>   	bool
> @@ -763,7 +678,7 @@ config CPU_ENDIAN_BE32
>   	  Support for the BE-32 (big-endian) mode on pre-ARMv6 processors.
>   
>   config CPU_HIGH_VECTOR
> -	depends on !MMU && CPU_CP15 && !CPU_ARM740T
> +	depends on !MMU && CPU_CP15
>   	bool "Select the High exception vector"
>   	help
>   	  Say Y here to select high exception vector(0xFFFF0000~).
> @@ -775,7 +690,7 @@ config CPU_HIGH_VECTOR
>   
>   config CPU_ICACHE_DISABLE
>   	bool "Disable I-Cache (I-bit)"
> -	depends on (CPU_CP15 && !(CPU_ARM720T || CPU_ARM740T || CPU_XSCALE || CPU_XSC3)) || CPU_V7M
> +	depends on (CPU_CP15 && !(CPU_XSCALE || CPU_XSC3)) || CPU_V7M
>   	help
>   	  Say Y here to disable the processor instruction cache. Unless
>   	  you have a reason not to or are unsure, say N.
> @@ -795,22 +710,9 @@ config CPU_DCACHE_DISABLE
>   	  Say Y here to disable the processor data cache. Unless
>   	  you have a reason not to or are unsure, say N.
>   
> -config CPU_DCACHE_SIZE
> -	hex
> -	depends on CPU_ARM740T || CPU_ARM946E
> -	default 0x00001000 if CPU_ARM740T
> -	default 0x00002000 # default size for ARM946E-S
> -	help
> -	  Some cores are synthesizable to have various sized cache. For
> -	  ARM946E-S case, it can vary from 0KB to 1MB.
> -	  To support such cache operations, it is efficient to know the size
> -	  before compile time.
> -	  If your SoC is configured to have a different size, define the value
> -	  here with proper conditions.
> -
>   config CPU_DCACHE_WRITETHROUGH
>   	bool "Force write through D-cache"
> -	depends on (CPU_ARM740T || CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM940T || CPU_ARM946E || CPU_ARM1020 || CPU_FA526) && !CPU_DCACHE_DISABLE
> +	depends on (CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM1020 || CPU_FA526) && !CPU_DCACHE_DISABLE
>   	default y if CPU_ARM925T
>   	help
>   	  Say Y here to use the data cache in writethrough mode. Unless you
> @@ -818,7 +720,7 @@ config CPU_DCACHE_WRITETHROUGH
>   
>   config CPU_CACHE_ROUND_ROBIN
>   	bool "Round robin I and D cache replacement algorithm"
> -	depends on (CPU_ARM926T || CPU_ARM946E || CPU_ARM1020) && (!CPU_ICACHE_DISABLE || !CPU_DCACHE_DISABLE)
> +	depends on (CPU_ARM926T || CPU_ARM1020) && (!CPU_ICACHE_DISABLE || !CPU_DCACHE_DISABLE)
>   	help
>   	  Say Y here to use the predictable round-robin cache replacement
>   	  policy.  Unless you specifically require this or are unsure, say N.
> diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile
> index 3510503bc5e6..233d273e8c7f 100644
> --- a/arch/arm/mm/Makefile
> +++ b/arch/arm/mm/Makefile
> @@ -75,16 +75,11 @@ obj-$(CONFIG_CPU_TLB_FA)	+= tlb-fa.o
>   AFLAGS_tlb-v6.o		:=-Wa,-march=armv6
>   AFLAGS_tlb-v7.o		:=-Wa,-march=armv7-a
>   
> -obj-$(CONFIG_CPU_ARM7TDMI)	+= proc-arm7tdmi.o
>   obj-$(CONFIG_CPU_ARM720T)	+= proc-arm720.o
> -obj-$(CONFIG_CPU_ARM740T)	+= proc-arm740.o
> -obj-$(CONFIG_CPU_ARM9TDMI)	+= proc-arm9tdmi.o
>   obj-$(CONFIG_CPU_ARM920T)	+= proc-arm920.o
>   obj-$(CONFIG_CPU_ARM922T)	+= proc-arm922.o
>   obj-$(CONFIG_CPU_ARM925T)	+= proc-arm925.o
>   obj-$(CONFIG_CPU_ARM926T)	+= proc-arm926.o
> -obj-$(CONFIG_CPU_ARM940T)	+= proc-arm940.o
> -obj-$(CONFIG_CPU_ARM946E)	+= proc-arm946.o
>   obj-$(CONFIG_CPU_FA526)		+= proc-fa526.o
>   obj-$(CONFIG_CPU_ARM1020)	+= proc-arm1020.o
>   obj-$(CONFIG_CPU_ARM1020E)	+= proc-arm1020e.o
> diff --git a/arch/arm/mm/proc-arm740.S b/arch/arm/mm/proc-arm740.S
> deleted file mode 100644
> index f2ec3bc60874..000000000000
> --- a/arch/arm/mm/proc-arm740.S
> +++ /dev/null
> @@ -1,147 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0-only */
> -/*
> - *  linux/arch/arm/mm/arm740.S: utility functions for ARM740
> - *
> - *  Copyright (C) 2004-2006 Hyok S. Choi (hyok.choi@xxxxxxxxxxx)
> - */
> -#include <linux/linkage.h>
> -#include <linux/init.h>
> -#include <linux/pgtable.h>
> -#include <asm/assembler.h>
> -#include <asm/asm-offsets.h>
> -#include <asm/hwcap.h>
> -#include <asm/pgtable-hwdef.h>
> -#include <asm/ptrace.h>
> -
> -#include "proc-macros.S"
> -
> -	.text
> -/*
> - * cpu_arm740_proc_init()
> - * cpu_arm740_do_idle()
> - * cpu_arm740_dcache_clean_area()
> - * cpu_arm740_switch_mm()
> - *
> - * These are not required.
> - */
> -ENTRY(cpu_arm740_proc_init)
> -ENTRY(cpu_arm740_do_idle)
> -ENTRY(cpu_arm740_dcache_clean_area)
> -ENTRY(cpu_arm740_switch_mm)
> -	ret	lr
> -
> -/*
> - * cpu_arm740_proc_fin()
> - */
> -ENTRY(cpu_arm740_proc_fin)
> -	mrc	p15, 0, r0, c1, c0, 0
> -	bic	r0, r0, #0x3f000000		@ bank/f/lock/s
> -	bic	r0, r0, #0x0000000c		@ w-buffer/cache
> -	mcr	p15, 0, r0, c1, c0, 0		@ disable caches
> -	ret	lr
> -
> -/*
> - * cpu_arm740_reset(loc)
> - * Params  : r0 = address to jump to
> - * Notes   : This sets up everything for a reset
> - */
> -	.pushsection	.idmap.text, "ax"
> -ENTRY(cpu_arm740_reset)
> -	mov	ip, #0
> -	mcr	p15, 0, ip, c7, c0, 0		@ invalidate cache
> -	mrc	p15, 0, ip, c1, c0, 0		@ get ctrl register
> -	bic	ip, ip, #0x0000000c		@ ............wc..
> -	mcr	p15, 0, ip, c1, c0, 0		@ ctrl register
> -	ret	r0
> -ENDPROC(cpu_arm740_reset)
> -	.popsection
> -
> -	.type	__arm740_setup, #function
> -__arm740_setup:
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c0, 0		@ invalidate caches
> -
> -	mcr	p15, 0, r0, c6, c3		@ disable area 3~7
> -	mcr	p15, 0, r0, c6, c4
> -	mcr	p15, 0, r0, c6, c5
> -	mcr	p15, 0, r0, c6, c6
> -	mcr	p15, 0, r0, c6, c7
> -
> -	mov	r0, #0x0000003F			@ base = 0, size = 4GB
> -	mcr	p15, 0, r0, c6,	c0		@ set area 0, default
> -
> -	ldr	r0, =(CONFIG_DRAM_BASE & 0xFFFFF000) @ base[31:12] of RAM
> -	ldr	r3, =(CONFIG_DRAM_SIZE >> 12)	@ size of RAM (must be >= 4KB)
> -	mov	r4, #10				@ 11 is the minimum (4KB)
> -1:	add	r4, r4, #1			@ area size *= 2
> -	movs	r3, r3, lsr #1
> -	bne	1b				@ count not zero r-shift
> -	orr	r0, r0, r4, lsl #1		@ the area register value
> -	orr	r0, r0, #1			@ set enable bit
> -	mcr	p15, 0, r0, c6,	c1		@ set area 1, RAM
> -
> -	ldr	r0, =(CONFIG_FLASH_MEM_BASE & 0xFFFFF000) @ base[31:12] of FLASH
> -	ldr	r3, =(CONFIG_FLASH_SIZE >> 12)	@ size of FLASH (must be >= 4KB)
> -	cmp	r3, #0
> -	moveq	r0, #0
> -	beq	2f
> -	mov	r4, #10				@ 11 is the minimum (4KB)
> -1:	add	r4, r4, #1			@ area size *= 2
> -	movs	r3, r3, lsr #1
> -	bne	1b				@ count not zero r-shift
> -	orr	r0, r0, r4, lsl #1		@ the area register value
> -	orr	r0, r0, #1			@ set enable bit
> -2:	mcr	p15, 0, r0, c6,	c2		@ set area 2, ROM/FLASH
> -
> -	mov	r0, #0x06
> -	mcr	p15, 0, r0, c2, c0		@ Region 1&2 cacheable
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mov	r0, #0x00			@ disable whole write buffer
> -#else
> -	mov	r0, #0x02			@ Region 1 write bufferred
> -#endif
> -	mcr	p15, 0, r0, c3, c0
> -
> -	mov	r0, #0x10000
> -	sub	r0, r0, #1			@ r0 = 0xffff
> -	mcr	p15, 0, r0, c5, c0		@ all read/write access
> -
> -	mrc	p15, 0, r0, c1, c0		@ get control register
> -	bic	r0, r0, #0x3F000000		@ set to standard caching mode
> -						@ need some benchmark
> -	orr	r0, r0, #0x0000000d		@ MPU/Cache/WB
> -
> -	ret	lr
> -
> -	.size	__arm740_setup, . - __arm740_setup
> -
> -	__INITDATA
> -
> -	@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
> -	define_processor_functions arm740, dabort=v4t_late_abort, pabort=legacy_pabort, nommu=1
> -
> -	.section ".rodata"
> -
> -	string	cpu_arch_name, "armv4"
> -	string	cpu_elf_name, "v4"
> -	string	cpu_arm740_name, "ARM740T"
> -
> -	.align
> -
> -	.section ".proc.info.init", "a"
> -	.type	__arm740_proc_info,#object
> -__arm740_proc_info:
> -	.long	0x41807400
> -	.long	0xfffffff0
> -	.long	0
> -	.long	0
> -	initfn	__arm740_setup, __arm740_proc_info
> -	.long	cpu_arch_name
> -	.long	cpu_elf_name
> -	.long	HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_26BIT
> -	.long	cpu_arm740_name
> -	.long	arm740_processor_functions
> -	.long	0
> -	.long	0
> -	.long	v4_cache_fns			@ cache model
> -	.size	__arm740_proc_info, . - __arm740_proc_info
> diff --git a/arch/arm/mm/proc-arm7tdmi.S b/arch/arm/mm/proc-arm7tdmi.S
> deleted file mode 100644
> index 01bbe7576c1c..000000000000
> --- a/arch/arm/mm/proc-arm7tdmi.S
> +++ /dev/null
> @@ -1,110 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0-only */
> -/*
> - *  linux/arch/arm/mm/proc-arm7tdmi.S: utility functions for ARM7TDMI
> - *
> - *  Copyright (C) 2003-2006 Hyok S. Choi <hyok.choi@xxxxxxxxxxx>
> - */
> -#include <linux/linkage.h>
> -#include <linux/init.h>
> -#include <linux/pgtable.h>
> -#include <asm/assembler.h>
> -#include <asm/asm-offsets.h>
> -#include <asm/hwcap.h>
> -#include <asm/pgtable-hwdef.h>
> -#include <asm/ptrace.h>
> -
> -#include "proc-macros.S"
> -
> -	.text
> -/*
> - * cpu_arm7tdmi_proc_init()
> - * cpu_arm7tdmi_do_idle()
> - * cpu_arm7tdmi_dcache_clean_area()
> - * cpu_arm7tdmi_switch_mm()
> - *
> - * These are not required.
> - */
> -ENTRY(cpu_arm7tdmi_proc_init)
> -ENTRY(cpu_arm7tdmi_do_idle)
> -ENTRY(cpu_arm7tdmi_dcache_clean_area)
> -ENTRY(cpu_arm7tdmi_switch_mm)
> -		ret	lr
> -
> -/*
> - * cpu_arm7tdmi_proc_fin()
> - */
> -ENTRY(cpu_arm7tdmi_proc_fin)
> -		ret	lr
> -
> -/*
> - * Function: cpu_arm7tdmi_reset(loc)
> - * Params  : loc(r0)	address to jump to
> - * Purpose : Sets up everything for a reset and jump to the location for soft reset.
> - */
> -		.pushsection	.idmap.text, "ax"
> -ENTRY(cpu_arm7tdmi_reset)
> -		ret	r0
> -ENDPROC(cpu_arm7tdmi_reset)
> -		.popsection
> -
> -		.type	__arm7tdmi_setup, #function
> -__arm7tdmi_setup:
> -		ret	lr
> -		.size	__arm7tdmi_setup, . - __arm7tdmi_setup
> -
> -		__INITDATA
> -
> -		@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
> -		define_processor_functions arm7tdmi, dabort=v4t_late_abort, pabort=legacy_pabort, nommu=1
> -
> -		.section ".rodata"
> -
> -		string	cpu_arch_name, "armv4t"
> -		string	cpu_elf_name, "v4"
> -		string	cpu_arm7tdmi_name, "ARM7TDMI"
> -		string	cpu_triscenda7_name, "Triscend-A7x"
> -		string	cpu_at91_name, "Atmel-AT91M40xxx"
> -		string	cpu_s3c3410_name, "Samsung-S3C3410"
> -		string	cpu_s3c44b0x_name, "Samsung-S3C44B0x"
> -		string	cpu_s3c4510b_name, "Samsung-S3C4510B"
> -		string	cpu_s3c4530_name, "Samsung-S3C4530"
> -		string	cpu_netarm_name, "NETARM"
> -
> -		.align
> -
> -		.section ".proc.info.init", "a"
> -
> -.macro arm7tdmi_proc_info name:req, cpu_val:req, cpu_mask:req, cpu_name:req, \
> -	extra_hwcaps=0
> -		.type	__\name\()_proc_info, #object
> -__\name\()_proc_info:
> -		.long	\cpu_val
> -		.long	\cpu_mask
> -		.long	0
> -		.long	0
> -		initfn	__arm7tdmi_setup, __\name\()_proc_info
> -		.long	cpu_arch_name
> -		.long	cpu_elf_name
> -		.long	HWCAP_SWP | HWCAP_26BIT | ( \extra_hwcaps )
> -		.long	\cpu_name
> -		.long	arm7tdmi_processor_functions
> -		.long	0
> -		.long	0
> -		.long	v4_cache_fns
> -		.size	__\name\()_proc_info, . - __\name\()_proc_info
> -.endm
> -
> -		arm7tdmi_proc_info arm7tdmi, 0x41007700, 0xfff8ff00, \
> -			cpu_arm7tdmi_name
> -		arm7tdmi_proc_info triscenda7, 0x0001d2ff, 0x0001ffff, \
> -			cpu_triscenda7_name, extra_hwcaps=HWCAP_THUMB
> -		arm7tdmi_proc_info at91, 0x14000040, 0xfff000e0, \
> -			cpu_at91_name, extra_hwcaps=HWCAP_THUMB
> -		arm7tdmi_proc_info s3c4510b, 0x36365000, 0xfffff000, \
> -			cpu_s3c4510b_name, extra_hwcaps=HWCAP_THUMB
> -		arm7tdmi_proc_info s3c4530, 0x4c000000, 0xfff000e0, \
> -			cpu_s3c4530_name, extra_hwcaps=HWCAP_THUMB
> -		arm7tdmi_proc_info s3c3410, 0x34100000, 0xffff0000, \
> -			cpu_s3c3410_name, extra_hwcaps=HWCAP_THUMB
> -		arm7tdmi_proc_info s3c44b0x, 0x44b00000, 0xffff0000, \
> -			cpu_s3c44b0x_name, extra_hwcaps=HWCAP_THUMB
> diff --git a/arch/arm/mm/proc-arm940.S b/arch/arm/mm/proc-arm940.S
> deleted file mode 100644
> index cf9bfcc825ca..000000000000
> --- a/arch/arm/mm/proc-arm940.S
> +++ /dev/null
> @@ -1,360 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0-only */
> -/*
> - *  linux/arch/arm/mm/arm940.S: utility functions for ARM940T
> - *
> - *  Copyright (C) 2004-2006 Hyok S. Choi (hyok.choi@xxxxxxxxxxx)
> - */
> -#include <linux/linkage.h>
> -#include <linux/init.h>
> -#include <linux/pgtable.h>
> -#include <asm/assembler.h>
> -#include <asm/hwcap.h>
> -#include <asm/pgtable-hwdef.h>
> -#include <asm/ptrace.h>
> -#include "proc-macros.S"
> -
> -/* ARM940T has a 4KB DCache comprising 256 lines of 4 words */
> -#define CACHE_DLINESIZE	16
> -#define CACHE_DSEGMENTS	4
> -#define CACHE_DENTRIES	64
> -
> -	.text
> -/*
> - * cpu_arm940_proc_init()
> - * cpu_arm940_switch_mm()
> - *
> - * These are not required.
> - */
> -ENTRY(cpu_arm940_proc_init)
> -ENTRY(cpu_arm940_switch_mm)
> -	ret	lr
> -
> -/*
> - * cpu_arm940_proc_fin()
> - */
> -ENTRY(cpu_arm940_proc_fin)
> -	mrc	p15, 0, r0, c1, c0, 0		@ ctrl register
> -	bic	r0, r0, #0x00001000		@ i-cache
> -	bic	r0, r0, #0x00000004		@ d-cache
> -	mcr	p15, 0, r0, c1, c0, 0		@ disable caches
> -	ret	lr
> -
> -/*
> - * cpu_arm940_reset(loc)
> - * Params  : r0 = address to jump to
> - * Notes   : This sets up everything for a reset
> - */
> -	.pushsection	.idmap.text, "ax"
> -ENTRY(cpu_arm940_reset)
> -	mov	ip, #0
> -	mcr	p15, 0, ip, c7, c5, 0		@ flush I cache
> -	mcr	p15, 0, ip, c7, c6, 0		@ flush D cache
> -	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
> -	mrc	p15, 0, ip, c1, c0, 0		@ ctrl register
> -	bic	ip, ip, #0x00000005		@ .............c.p
> -	bic	ip, ip, #0x00001000		@ i-cache
> -	mcr	p15, 0, ip, c1, c0, 0		@ ctrl register
> -	ret	r0
> -ENDPROC(cpu_arm940_reset)
> -	.popsection
> -
> -/*
> - * cpu_arm940_do_idle()
> - */
> -	.align	5
> -ENTRY(cpu_arm940_do_idle)
> -	mcr	p15, 0, r0, c7, c0, 4		@ Wait for interrupt
> -	ret	lr
> -
> -/*
> - *	flush_icache_all()
> - *
> - *	Unconditionally clean and invalidate the entire icache.
> - */
> -ENTRY(arm940_flush_icache_all)
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	ret	lr
> -ENDPROC(arm940_flush_icache_all)
> -
> -/*
> - *	flush_user_cache_all()
> - */
> -ENTRY(arm940_flush_user_cache_all)
> -	/* FALLTHROUGH */
> -
> -/*
> - *	flush_kern_cache_all()
> - *
> - *	Clean and invalidate the entire cache.
> - */
> -ENTRY(arm940_flush_kern_cache_all)
> -	mov	r2, #VM_EXEC
> -	/* FALLTHROUGH */
> -
> -/*
> - *	flush_user_cache_range(start, end, flags)
> - *
> - *	There is no efficient way to flush a range of cache entries
> - *	in the specified address range. Thus, flushes all.
> - *
> - *	- start	- start address (inclusive)
> - *	- end	- end address (exclusive)
> - *	- flags	- vm_flags describing address space
> - */
> -ENTRY(arm940_flush_user_cache_range)
> -	mov	ip, #0
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mcr	p15, 0, ip, c7, c6, 0		@ flush D cache
> -#else
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 4	@ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
> -2:	mcr	p15, 0, r3, c7, c14, 2		@ clean/flush D index
> -	subs	r3, r3, #1 << 26
> -	bcs	2b				@ entries 63 to 0
> -	subs	r1, r1, #1 << 4
> -	bcs	1b				@ segments 3 to 0
> -#endif
> -	tst	r2, #VM_EXEC
> -	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
> -	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	coherent_kern_range(start, end)
> - *
> - *	Ensure coherency between the Icache and the Dcache in the
> - *	region described by start, end.  If you have non-snooping
> - *	Harvard caches, you need to implement this function.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -ENTRY(arm940_coherent_kern_range)
> -	/* FALLTHROUGH */
> -
> -/*
> - *	coherent_user_range(start, end)
> - *
> - *	Ensure coherency between the Icache and the Dcache in the
> - *	region described by start, end.  If you have non-snooping
> - *	Harvard caches, you need to implement this function.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -ENTRY(arm940_coherent_user_range)
> -	/* FALLTHROUGH */
> -
> -/*
> - *	flush_kern_dcache_area(void *addr, size_t size)
> - *
> - *	Ensure no D cache aliasing occurs, either with itself or
> - *	the I cache
> - *
> - *	- addr	- kernel address
> - *	- size	- region size
> - */
> -ENTRY(arm940_flush_kern_dcache_area)
> -	mov	r0, #0
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 4	@ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
> -2:	mcr	p15, 0, r3, c7, c14, 2		@ clean/flush D index
> -	subs	r3, r3, #1 << 26
> -	bcs	2b				@ entries 63 to 0
> -	subs	r1, r1, #1 << 4
> -	bcs	1b				@ segments 7 to 0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_inv_range(start, end)
> - *
> - *	There is no efficient way to invalidate a specifid virtual
> - *	address range. Thus, invalidates all.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -arm940_dma_inv_range:
> -	mov	ip, #0
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 4	@ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
> -2:	mcr	p15, 0, r3, c7, c6, 2		@ flush D entry
> -	subs	r3, r3, #1 << 26
> -	bcs	2b				@ entries 63 to 0
> -	subs	r1, r1, #1 << 4
> -	bcs	1b				@ segments 7 to 0
> -	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_clean_range(start, end)
> - *
> - *	There is no efficient way to clean a specifid virtual
> - *	address range. Thus, cleans all.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -arm940_dma_clean_range:
> -ENTRY(cpu_arm940_dcache_clean_area)
> -	mov	ip, #0
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 4	@ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
> -2:	mcr	p15, 0, r3, c7, c10, 2		@ clean D entry
> -	subs	r3, r3, #1 << 26
> -	bcs	2b				@ entries 63 to 0
> -	subs	r1, r1, #1 << 4
> -	bcs	1b				@ segments 7 to 0
> -#endif
> -	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_flush_range(start, end)
> - *
> - *	There is no efficient way to clean and invalidate a specifid
> - *	virtual address range.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -ENTRY(arm940_dma_flush_range)
> -	mov	ip, #0
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 4	@ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
> -2:
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mcr	p15, 0, r3, c7, c14, 2		@ clean/flush D entry
> -#else
> -	mcr	p15, 0, r3, c7, c6, 2		@ invalidate D entry
> -#endif
> -	subs	r3, r3, #1 << 26
> -	bcs	2b				@ entries 63 to 0
> -	subs	r1, r1, #1 << 4
> -	bcs	1b				@ segments 7 to 0
> -	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_map_area(start, size, dir)
> - *	- start	- kernel virtual start address
> - *	- size	- size of region
> - *	- dir	- DMA direction
> - */
> -ENTRY(arm940_dma_map_area)
> -	add	r1, r1, r0
> -	cmp	r2, #DMA_TO_DEVICE
> -	beq	arm940_dma_clean_range
> -	bcs	arm940_dma_inv_range
> -	b	arm940_dma_flush_range
> -ENDPROC(arm940_dma_map_area)
> -
> -/*
> - *	dma_unmap_area(start, size, dir)
> - *	- start	- kernel virtual start address
> - *	- size	- size of region
> - *	- dir	- DMA direction
> - */
> -ENTRY(arm940_dma_unmap_area)
> -	ret	lr
> -ENDPROC(arm940_dma_unmap_area)
> -
> -	.globl	arm940_flush_kern_cache_louis
> -	.equ	arm940_flush_kern_cache_louis, arm940_flush_kern_cache_all
> -
> -	@ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S)
> -	define_cache_functions arm940
> -
> -	.type	__arm940_setup, #function
> -__arm940_setup:
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	mcr	p15, 0, r0, c7, c6, 0		@ invalidate D cache
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -
> -	mcr	p15, 0, r0, c6, c3, 0		@ disable data area 3~7
> -	mcr	p15, 0, r0, c6, c4, 0
> -	mcr	p15, 0, r0, c6, c5, 0
> -	mcr	p15, 0, r0, c6, c6, 0
> -	mcr	p15, 0, r0, c6, c7, 0
> -
> -	mcr	p15, 0, r0, c6, c3, 1		@ disable instruction area 3~7
> -	mcr	p15, 0, r0, c6, c4, 1
> -	mcr	p15, 0, r0, c6, c5, 1
> -	mcr	p15, 0, r0, c6, c6, 1
> -	mcr	p15, 0, r0, c6, c7, 1
> -
> -	mov	r0, #0x0000003F			@ base = 0, size = 4GB
> -	mcr	p15, 0, r0, c6,	c0, 0		@ set area 0, default
> -	mcr	p15, 0, r0, c6,	c0, 1
> -
> -	ldr	r0, =(CONFIG_DRAM_BASE & 0xFFFFF000) @ base[31:12] of RAM
> -	ldr	r7, =CONFIG_DRAM_SIZE >> 12	@ size of RAM (must be >= 4KB)
> -	pr_val	r3, r0, r7, #1
> -	mcr	p15, 0, r3, c6,	c1, 0		@ set area 1, RAM
> -	mcr	p15, 0, r3, c6,	c1, 1
> -
> -	ldr	r0, =(CONFIG_FLASH_MEM_BASE & 0xFFFFF000) @ base[31:12] of FLASH
> -	ldr	r7, =CONFIG_FLASH_SIZE		@ size of FLASH (must be >= 4KB)
> -	pr_val	r3, r0, r6, #1
> -	mcr	p15, 0, r3, c6,	c2, 0		@ set area 2, ROM/FLASH
> -	mcr	p15, 0, r3, c6,	c2, 1
> -
> -	mov	r0, #0x06
> -	mcr	p15, 0, r0, c2, c0, 0		@ Region 1&2 cacheable
> -	mcr	p15, 0, r0, c2, c0, 1
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mov	r0, #0x00			@ disable whole write buffer
> -#else
> -	mov	r0, #0x02			@ Region 1 write bufferred
> -#endif
> -	mcr	p15, 0, r0, c3, c0, 0
> -
> -	mov	r0, #0x10000
> -	sub	r0, r0, #1			@ r0 = 0xffff
> -	mcr	p15, 0, r0, c5, c0, 0		@ all read/write access
> -	mcr	p15, 0, r0, c5, c0, 1
> -
> -	mrc	p15, 0, r0, c1, c0		@ get control register
> -	orr	r0, r0, #0x00001000		@ I-cache
> -	orr	r0, r0, #0x00000005		@ MPU/D-cache
> -
> -	ret	lr
> -
> -	.size	__arm940_setup, . - __arm940_setup
> -
> -	__INITDATA
> -
> -	@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
> -	define_processor_functions arm940, dabort=nommu_early_abort, pabort=legacy_pabort, nommu=1
> -
> -	.section ".rodata"
> -
> -	string	cpu_arch_name, "armv4t"
> -	string	cpu_elf_name, "v4"
> -	string	cpu_arm940_name, "ARM940T"
> -
> -	.align
> -
> -	.section ".proc.info.init", "a"
> -
> -	.type	__arm940_proc_info,#object
> -__arm940_proc_info:
> -	.long	0x41009400
> -	.long	0xff00fff0
> -	.long	0
> -	initfn	__arm940_setup, __arm940_proc_info
> -	.long	cpu_arch_name
> -	.long	cpu_elf_name
> -	.long	HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB
> -	.long	cpu_arm940_name
> -	.long	arm940_processor_functions
> -	.long	0
> -	.long	0
> -	.long	arm940_cache_fns
> -	.size	__arm940_proc_info, . - __arm940_proc_info
> -
> diff --git a/arch/arm/mm/proc-arm946.S b/arch/arm/mm/proc-arm946.S
> deleted file mode 100644
> index 6fb3898ad1cd..000000000000
> --- a/arch/arm/mm/proc-arm946.S
> +++ /dev/null
> @@ -1,415 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0-only */
> -/*
> - *  linux/arch/arm/mm/arm946.S: utility functions for ARM946E-S
> - *
> - *  Copyright (C) 2004-2006 Hyok S. Choi (hyok.choi@xxxxxxxxxxx)
> - *
> - *  (Many of cache codes are from proc-arm926.S)
> - */
> -#include <linux/linkage.h>
> -#include <linux/init.h>
> -#include <linux/pgtable.h>
> -#include <asm/assembler.h>
> -#include <asm/hwcap.h>
> -#include <asm/pgtable-hwdef.h>
> -#include <asm/ptrace.h>
> -#include "proc-macros.S"
> -
> -/*
> - * ARM946E-S is synthesizable to have 0KB to 1MB sized D-Cache,
> - * comprising 256 lines of 32 bytes (8 words).
> - */
> -#define CACHE_DSIZE	(CONFIG_CPU_DCACHE_SIZE) /* typically 8KB. */
> -#define CACHE_DLINESIZE	32			/* fixed */
> -#define CACHE_DSEGMENTS	4			/* fixed */
> -#define CACHE_DENTRIES	(CACHE_DSIZE / CACHE_DSEGMENTS / CACHE_DLINESIZE)
> -#define CACHE_DLIMIT	(CACHE_DSIZE * 4)	/* benchmark needed */
> -
> -	.text
> -/*
> - * cpu_arm946_proc_init()
> - * cpu_arm946_switch_mm()
> - *
> - * These are not required.
> - */
> -ENTRY(cpu_arm946_proc_init)
> -ENTRY(cpu_arm946_switch_mm)
> -	ret	lr
> -
> -/*
> - * cpu_arm946_proc_fin()
> - */
> -ENTRY(cpu_arm946_proc_fin)
> -	mrc	p15, 0, r0, c1, c0, 0		@ ctrl register
> -	bic	r0, r0, #0x00001000		@ i-cache
> -	bic	r0, r0, #0x00000004		@ d-cache
> -	mcr	p15, 0, r0, c1, c0, 0		@ disable caches
> -	ret	lr
> -
> -/*
> - * cpu_arm946_reset(loc)
> - * Params  : r0 = address to jump to
> - * Notes   : This sets up everything for a reset
> - */
> -	.pushsection	.idmap.text, "ax"
> -ENTRY(cpu_arm946_reset)
> -	mov	ip, #0
> -	mcr	p15, 0, ip, c7, c5, 0		@ flush I cache
> -	mcr	p15, 0, ip, c7, c6, 0		@ flush D cache
> -	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
> -	mrc	p15, 0, ip, c1, c0, 0		@ ctrl register
> -	bic	ip, ip, #0x00000005		@ .............c.p
> -	bic	ip, ip, #0x00001000		@ i-cache
> -	mcr	p15, 0, ip, c1, c0, 0		@ ctrl register
> -	ret	r0
> -ENDPROC(cpu_arm946_reset)
> -	.popsection
> -
> -/*
> - * cpu_arm946_do_idle()
> - */
> -	.align	5
> -ENTRY(cpu_arm946_do_idle)
> -	mcr	p15, 0, r0, c7, c0, 4		@ Wait for interrupt
> -	ret	lr
> -
> -/*
> - *	flush_icache_all()
> - *
> - *	Unconditionally clean and invalidate the entire icache.
> - */
> -ENTRY(arm946_flush_icache_all)
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	ret	lr
> -ENDPROC(arm946_flush_icache_all)
> -
> -/*
> - *	flush_user_cache_all()
> - */
> -ENTRY(arm946_flush_user_cache_all)
> -	/* FALLTHROUGH */
> -
> -/*
> - *	flush_kern_cache_all()
> - *
> - *	Clean and invalidate the entire cache.
> - */
> -ENTRY(arm946_flush_kern_cache_all)
> -	mov	r2, #VM_EXEC
> -	mov	ip, #0
> -__flush_whole_cache:
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mcr	p15, 0, ip, c7, c6, 0		@ flush D cache
> -#else
> -	mov	r1, #(CACHE_DSEGMENTS - 1) << 29 @ 4 segments
> -1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 4 @ n entries
> -2:	mcr	p15, 0, r3, c7, c14, 2		@ clean/flush D index
> -	subs	r3, r3, #1 << 4
> -	bcs	2b				@ entries n to 0
> -	subs	r1, r1, #1 << 29
> -	bcs	1b				@ segments 3 to 0
> -#endif
> -	tst	r2, #VM_EXEC
> -	mcrne	p15, 0, ip, c7, c5, 0		@ flush I cache
> -	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	flush_user_cache_range(start, end, flags)
> - *
> - *	Clean and invalidate a range of cache entries in the
> - *	specified address range.
> - *
> - *	- start	- start address (inclusive)
> - *	- end	- end address (exclusive)
> - *	- flags	- vm_flags describing address space
> - * (same as arm926)
> - */
> -ENTRY(arm946_flush_user_cache_range)
> -	mov	ip, #0
> -	sub	r3, r1, r0			@ calculate total size
> -	cmp	r3, #CACHE_DLIMIT
> -	bhs	__flush_whole_cache
> -
> -1:	tst	r2, #VM_EXEC
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
> -	mcrne	p15, 0, r0, c7, c5, 1		@ invalidate I entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
> -	mcrne	p15, 0, r0, c7, c5, 1		@ invalidate I entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -#else
> -	mcr	p15, 0, r0, c7, c14, 1		@ clean and invalidate D entry
> -	mcrne	p15, 0, r0, c7, c5, 1		@ invalidate I entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	mcr	p15, 0, r0, c7, c14, 1		@ clean and invalidate D entry
> -	mcrne	p15, 0, r0, c7, c5, 1		@ invalidate I entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -#endif
> -	cmp	r0, r1
> -	blo	1b
> -	tst	r2, #VM_EXEC
> -	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	coherent_kern_range(start, end)
> - *
> - *	Ensure coherency between the Icache and the Dcache in the
> - *	region described by start, end.  If you have non-snooping
> - *	Harvard caches, you need to implement this function.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - */
> -ENTRY(arm946_coherent_kern_range)
> -	/* FALLTHROUGH */
> -
> -/*
> - *	coherent_user_range(start, end)
> - *
> - *	Ensure coherency between the Icache and the Dcache in the
> - *	region described by start, end.  If you have non-snooping
> - *	Harvard caches, you need to implement this function.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - * (same as arm926)
> - */
> -ENTRY(arm946_coherent_user_range)
> -	bic	r0, r0, #CACHE_DLINESIZE - 1
> -1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
> -	mcr	p15, 0, r0, c7, c5, 1		@ invalidate I entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	cmp	r0, r1
> -	blo	1b
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	mov	r0, #0
> -	ret	lr
> -
> -/*
> - *	flush_kern_dcache_area(void *addr, size_t size)
> - *
> - *	Ensure no D cache aliasing occurs, either with itself or
> - *	the I cache
> - *
> - *	- addr	- kernel address
> - *	- size	- region size
> - * (same as arm926)
> - */
> -ENTRY(arm946_flush_kern_dcache_area)
> -	add	r1, r0, r1
> -1:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	cmp	r0, r1
> -	blo	1b
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_inv_range(start, end)
> - *
> - *	Invalidate (discard) the specified virtual address range.
> - *	May not write back any entries.  If 'start' or 'end'
> - *	are not cache line aligned, those lines must be written
> - *	back.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - * (same as arm926)
> - */
> -arm946_dma_inv_range:
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	tst	r0, #CACHE_DLINESIZE - 1
> -	mcrne	p15, 0, r0, c7, c10, 1		@ clean D entry
> -	tst	r1, #CACHE_DLINESIZE - 1
> -	mcrne	p15, 0, r1, c7, c10, 1		@ clean D entry
> -#endif
> -	bic	r0, r0, #CACHE_DLINESIZE - 1
> -1:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	cmp	r0, r1
> -	blo	1b
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_clean_range(start, end)
> - *
> - *	Clean the specified virtual address range.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - *
> - * (same as arm926)
> - */
> -arm946_dma_clean_range:
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	bic	r0, r0, #CACHE_DLINESIZE - 1
> -1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	cmp	r0, r1
> -	blo	1b
> -#endif
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_flush_range(start, end)
> - *
> - *	Clean and invalidate the specified virtual address range.
> - *
> - *	- start	- virtual start address
> - *	- end	- virtual end address
> - *
> - * (same as arm926)
> - */
> -ENTRY(arm946_dma_flush_range)
> -	bic	r0, r0, #CACHE_DLINESIZE - 1
> -1:
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
> -#else
> -	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
> -#endif
> -	add	r0, r0, #CACHE_DLINESIZE
> -	cmp	r0, r1
> -	blo	1b
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -/*
> - *	dma_map_area(start, size, dir)
> - *	- start	- kernel virtual start address
> - *	- size	- size of region
> - *	- dir	- DMA direction
> - */
> -ENTRY(arm946_dma_map_area)
> -	add	r1, r1, r0
> -	cmp	r2, #DMA_TO_DEVICE
> -	beq	arm946_dma_clean_range
> -	bcs	arm946_dma_inv_range
> -	b	arm946_dma_flush_range
> -ENDPROC(arm946_dma_map_area)
> -
> -/*
> - *	dma_unmap_area(start, size, dir)
> - *	- start	- kernel virtual start address
> - *	- size	- size of region
> - *	- dir	- DMA direction
> - */
> -ENTRY(arm946_dma_unmap_area)
> -	ret	lr
> -ENDPROC(arm946_dma_unmap_area)
> -
> -	.globl	arm946_flush_kern_cache_louis
> -	.equ	arm946_flush_kern_cache_louis, arm946_flush_kern_cache_all
> -
> -	@ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S)
> -	define_cache_functions arm946
> -
> -ENTRY(cpu_arm946_dcache_clean_area)
> -#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
> -1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
> -	add	r0, r0, #CACHE_DLINESIZE
> -	subs	r1, r1, #CACHE_DLINESIZE
> -	bhi	1b
> -#endif
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -	ret	lr
> -
> -	.type	__arm946_setup, #function
> -__arm946_setup:
> -	mov	r0, #0
> -	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
> -	mcr	p15, 0, r0, c7, c6, 0		@ invalidate D cache
> -	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
> -
> -	mcr	p15, 0, r0, c6, c3, 0		@ disable memory region 3~7
> -	mcr	p15, 0, r0, c6, c4, 0
> -	mcr	p15, 0, r0, c6, c5, 0
> -	mcr	p15, 0, r0, c6, c6, 0
> -	mcr	p15, 0, r0, c6, c7, 0
> -
> -	mov	r0, #0x0000003F			@ base = 0, size = 4GB
> -	mcr	p15, 0, r0, c6,	c0, 0		@ set region 0, default
> -
> -	ldr	r0, =(CONFIG_DRAM_BASE & 0xFFFFF000) @ base[31:12] of RAM
> -	ldr	r7, =CONFIG_DRAM_SIZE		@ size of RAM (must be >= 4KB)
> -	pr_val	r3, r0, r7, #1
> -	mcr	p15, 0, r3, c6, c1, 0
> -
> -	ldr	r0, =(CONFIG_FLASH_MEM_BASE & 0xFFFFF000) @ base[31:12] of FLASH
> -	ldr	r7, =CONFIG_FLASH_SIZE		@ size of FLASH (must be >= 4KB)
> -	pr_val	r3, r0, r7, #1
> -	mcr	p15, 0, r3, c6, c2, 0
> -
> -	mov	r0, #0x06
> -	mcr	p15, 0, r0, c2, c0, 0		@ region 1,2 d-cacheable
> -	mcr	p15, 0, r0, c2, c0, 1		@ region 1,2 i-cacheable
> -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
> -	mov	r0, #0x00			@ disable whole write buffer
> -#else
> -	mov	r0, #0x02			@ region 1 write bufferred
> -#endif
> -	mcr	p15, 0, r0, c3, c0, 0
> -
> -/*
> - *  Access Permission Settings for future permission control by PU.
> - *
> - *				priv.	user
> - * 	region 0 (whole)	rw	--	: b0001
> - * 	region 1 (RAM)		rw	rw	: b0011
> - * 	region 2 (FLASH)	rw	r-	: b0010
> - *	region 3~7 (none)	--	--	: b0000
> - */
> -	mov	r0, #0x00000031
> -	orr	r0, r0, #0x00000200
> -	mcr	p15, 0, r0, c5, c0, 2		@ set data access permission
> -	mcr	p15, 0, r0, c5, c0, 3		@ set inst. access permission
> -
> -	mrc	p15, 0, r0, c1, c0		@ get control register
> -	orr	r0, r0, #0x00001000		@ I-cache
> -	orr	r0, r0, #0x00000005		@ MPU/D-cache
> -#ifdef CONFIG_CPU_CACHE_ROUND_ROBIN
> -	orr	r0, r0, #0x00004000		@ .1.. .... .... ....
> -#endif
> -	ret	lr
> -
> -	.size	__arm946_setup, . - __arm946_setup
> -
> -	__INITDATA
> -
> -	@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
> -	define_processor_functions arm946, dabort=nommu_early_abort, pabort=legacy_pabort, nommu=1
> -
> -	.section ".rodata"
> -
> -	string	cpu_arch_name, "armv5te"
> -	string	cpu_elf_name, "v5t"
> -	string	cpu_arm946_name, "ARM946E-S"
> -
> -	.align
> -
> -	.section ".proc.info.init", "a"
> -	.type	__arm946_proc_info,#object
> -__arm946_proc_info:
> -	.long	0x41009460
> -	.long	0xff00fff0
> -	.long	0
> -	.long	0
> -	initfn	__arm946_setup, __arm946_proc_info
> -	.long	cpu_arch_name
> -	.long	cpu_elf_name
> -	.long	HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB
> -	.long	cpu_arm946_name
> -	.long	arm946_processor_functions
> -	.long	0
> -	.long	0
> -	.long	arm946_cache_fns
> -	.size	__arm946_proc_info, . - __arm946_proc_info
> -
> diff --git a/arch/arm/mm/proc-arm9tdmi.S b/arch/arm/mm/proc-arm9tdmi.S
> deleted file mode 100644
> index a054c0e9c034..000000000000
> --- a/arch/arm/mm/proc-arm9tdmi.S
> +++ /dev/null
> @@ -1,91 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0-only */
> -/*
> - *  linux/arch/arm/mm/proc-arm9tdmi.S: utility functions for ARM9TDMI
> - *
> - *  Copyright (C) 2003-2006 Hyok S. Choi <hyok.choi@xxxxxxxxxxx>
> - */
> -#include <linux/linkage.h>
> -#include <linux/init.h>
> -#include <linux/pgtable.h>
> -#include <asm/assembler.h>
> -#include <asm/asm-offsets.h>
> -#include <asm/hwcap.h>
> -#include <asm/pgtable-hwdef.h>
> -#include <asm/ptrace.h>
> -
> -#include "proc-macros.S"
> -
> -	.text
> -/*
> - * cpu_arm9tdmi_proc_init()
> - * cpu_arm9tdmi_do_idle()
> - * cpu_arm9tdmi_dcache_clean_area()
> - * cpu_arm9tdmi_switch_mm()
> - *
> - * These are not required.
> - */
> -ENTRY(cpu_arm9tdmi_proc_init)
> -ENTRY(cpu_arm9tdmi_do_idle)
> -ENTRY(cpu_arm9tdmi_dcache_clean_area)
> -ENTRY(cpu_arm9tdmi_switch_mm)
> -		ret	lr
> -
> -/*
> - * cpu_arm9tdmi_proc_fin()
> - */
> -ENTRY(cpu_arm9tdmi_proc_fin)
> -		ret	lr
> -
> -/*
> - * Function: cpu_arm9tdmi_reset(loc)
> - * Params  : loc(r0)	address to jump to
> - * Purpose : Sets up everything for a reset and jump to the location for soft reset.
> - */
> -		.pushsection	.idmap.text, "ax"
> -ENTRY(cpu_arm9tdmi_reset)
> -		ret	r0
> -ENDPROC(cpu_arm9tdmi_reset)
> -		.popsection
> -
> -		.type	__arm9tdmi_setup, #function
> -__arm9tdmi_setup:
> -		ret	lr
> -		.size	__arm9tdmi_setup, . - __arm9tdmi_setup
> -
> -		__INITDATA
> -
> -		@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
> -		define_processor_functions arm9tdmi, dabort=nommu_early_abort, pabort=legacy_pabort, nommu=1
> -
> -		.section ".rodata"
> -
> -		string	cpu_arch_name, "armv4t"
> -		string	cpu_elf_name, "v4"
> -		string	cpu_arm9tdmi_name, "ARM9TDMI"
> -		string	cpu_p2001_name, "P2001"
> -
> -		.align
> -
> -		.section ".proc.info.init", "a"
> -
> -.macro arm9tdmi_proc_info name:req, cpu_val:req, cpu_mask:req, cpu_name:req
> -		.type	__\name\()_proc_info, #object
> -__\name\()_proc_info:
> -		.long	\cpu_val
> -		.long	\cpu_mask
> -		.long	0
> -		.long	0
> -		initfn	__arm9tdmi_setup, __\name\()_proc_info
> -		.long	cpu_arch_name
> -		.long	cpu_elf_name
> -		.long	HWCAP_SWP | HWCAP_THUMB | HWCAP_26BIT
> -		.long	\cpu_name
> -		.long	arm9tdmi_processor_functions
> -		.long	0
> -		.long	0
> -		.long	v4_cache_fns
> -		.size	__\name\()_proc_info, . - __\name\()_proc_info
> -.endm
> -
> -	arm9tdmi_proc_info arm9tdmi, 0x41009900, 0xfff8ff00, cpu_arm9tdmi_name
> -	arm9tdmi_proc_info p2001, 0x41029000, 0xffffffff, cpu_p2001_name