[PATCH v1 2/2] arm64: dts: rockchip: Add gmac1 and change network settings

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>

New Version (v1.0) of R2 pro has swapped gmacs compared to the v00.

WAN-Port is now on gmac1 (RTL8211F) and lan-ports on gmac0 with mt7531
switch.

There is already a mt7531 dsa driver in mainline, but it needs to be
modified to work for this board.

Fixes: f901aaadaa2a ("arm64: dts: rockchip: Add Bananapi R2 Pro")
Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
---
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   | 36 +++++++++++++++++--
 1 file changed, 33 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
index a0388ff85ddf..067fe4a6b178 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
@@ -16,6 +16,7 @@ / {
 
 	aliases {
 		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		mmc0 = &sdmmc0;
 		mmc1 = &sdhci;
 	};
@@ -78,7 +79,6 @@ &gmac0 {
 	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
 	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
 	clock_in_out = "input";
-	phy-handle = <&rgmii_phy0>;
 	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac0_miim
@@ -90,8 +90,38 @@ &gmac0_rgmii_clk
 	snps,reset-active-low;
 	/* Reset time is 20ms, 100ms for rtl8211f */
 	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x0f>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+
+	snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+
 	tx_delay = <0x3c>;
 	rx_delay = <0x2f>;
+
 	status = "okay";
 };
 
@@ -315,8 +345,8 @@ &i2c5 {
 	status = "disabled";
 };
 
-&mdio0 {
-	rgmii_phy0: ethernet-phy@0 {
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <0x0>;
 	};
-- 
2.25.1