Re: [PATCH v3 2/2] drivers: usb: dwc3: Add AM62 USB wrapper driver

From: Aswath Govindraju
Date: Thu Apr 07 2022 - 05:14:03 EST

Next message: Krzysztof Kozlowski: "Re: [PATCH] phy: samsung: fix missing of_node_put()"
Previous message: Vlad Buslov: "Re: [PATCH net-next v2] net: openvswitch: fix uAPI incompatibility with existing user space"
In reply to: Roger Quadros: "Re: [PATCH v3 2/2] drivers: usb: dwc3: Add AM62 USB wrapper driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Roger,

On 07/04/22 14:24, Roger Quadros wrote:
>
>
> On 07/04/2022 11:27, Aswath Govindraju wrote:
>> Hi Roger,
>>
>> On 07/04/22 13:54, Aswath Govindraju wrote:
>>> Hi Roger,
>>>
>>> On 07/04/22 13:50, Roger Quadros wrote:
>>>> Hi Aswath,
>>>>
>>>> On 06/04/2022 16:52, Aswath Govindraju wrote:
>>>>> In AM62 SoC, the Designware Core USB3 IP is progammed to operate in USB2.0
>>>>> only mode. Add driver for AM62 USB DWC3 Wrapper.
>>>>>
>>>>> Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx>
>>>>> ---
>>>>>
>>>>> changes since v2:
>>>>> - Removed the implementation of detecting the role from the wrapper
>>>>> driver and moved the implementation to using linux,extcon-usb-gpio
>>>>> driver for role detection.
>>>>
>>>> I'm a bit puzzled. So ID is managed by extcon-usb-gpio driver and
>>>> VBUS is managed by this driver.
>>>>
>>>> So who decides the USB ports state based on the below truth table?
>>>>
>>>> + /*
>>>> + * ID | VBUS | STATE
>>>> + * -----------------
>>>> + * 0 | 0 | HOST
>>>> + * 0 | 1 | HOST
>>>> + * 1 | 0 | Disconnected (set mode valid to 0)
>>>> + * 1 | 1 | Device
>>>> + *
>>>> + */
>>>>
>>>> If only ID signal is available to extcon-usb-gpio driver it cannot detect
>>>> the Disconnected state. We need to set mode valid to 0 for disconnected state.
>>>>
>>>
>>> Yes that is correct, the mode valid signal needs to be set when there is
>>> no cable connected. I am slightly confused on why 0-0 state is not
>>> considered disconnected? So, whenever VBUS is not high it should be
>>> disconnected right?
>
> Not necessarily. We might be in host mode (ID=0) and just not turned on the VBUS regulator (VBUS=0).
> Is this to be treated as disconnected?
>

This should be treated as disconnected state right? Since the device is
not essentially connected to host and only after VBUS is supplied from
the host, the device starts to enumerate.

The controller will move to host mode but the devices will not get
enumerated. The device will get enumerated only after we supply VBUS and
this event will be registered and mode valid bit will be set.

> I'm just pointing out that things won't function anymore like the below code you had earlier
> as you have decoupled id_state from vbus_state.
>
> + /* detemine the role or find out if disconnect event */
> + if (id_state) {
> + detect_role = DEVICE;
> + if (vbus_state)
> + connect = 1;
> + } else {
> + detect_role = HOST;
> + connect = 1;
> + }
>
> Now you are setting connect independently of ID. i.e. connect = vbus_state.
>
> Is that what you want?
>

Yes, I changed it as I felt that the dependency can be removed.

Thanks,
Aswath

> cheers,
> -roger
>
>>>
>>
>> Sorry, pressed the send button without reading everything properly.
>>
>> The implementation is such that the extcon-usb-gpio only updates the
>> role to the core driver based on ID pin state and the Mode valid bit is
>> set by the wrapper based on the VBUS state.
>>
>> Thanks,
>> Aswath
>>
>>> Thanks,
>>> Aswath
>>>
>>>> cheers,
>>>> -roger
>>>>
>>>>
>>>>> - Updated the binding documentation and example to reflect the same.
>>>>>
>>>>>
>>>>> drivers/usb/dwc3/Kconfig | 9 +
>>>>> drivers/usb/dwc3/Makefile | 1 +
>>>>> drivers/usb/dwc3/dwc3-am62.c | 446 +++++++++++++++++++++++++++++++++++
>>>>> 3 files changed, 456 insertions(+)
>>>>> create mode 100644 drivers/usb/dwc3/dwc3-am62.c
>>>>>
>>>>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
>>>>> index c483f28b695d..cd9a734522a7 100644
>>>>> --- a/drivers/usb/dwc3/Kconfig
>>>>> +++ b/drivers/usb/dwc3/Kconfig
>>>>> @@ -159,4 +159,13 @@ config USB_DWC3_XILINX
>>>>> This driver handles both ZynqMP and Versal SoC operations.
>>>>> Say 'Y' or 'M' if you have one such device.
>>>>>
>>>>> +config USB_DWC3_AM62
>>>>> + tristate "Texas Instruments AM62 Platforms"
>>>>> + depends on ARCH_K3 || COMPILE_TEST
>>>>> + default USB_DWC3
>>>>> + help
>>>>> + Support TI's AM62 platforms with DesignWare Core USB3 IP.
>>>>> + The Designware Core USB3 IP is progammed to operate in
>>>>> + in USB 2.0 mode only.
>>>>> + Say 'Y' or 'M' here if you have one such device
>>>>> endif
>>>>> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
>>>>> index 2d499de6f66a..9f66bd82b639 100644
>>>>> --- a/drivers/usb/dwc3/Makefile
>>>>> +++ b/drivers/usb/dwc3/Makefile
>>>>> @@ -42,6 +42,7 @@ endif
>>>>> # and allyesconfig builds.
>>>>> ##
>>>>>
>>>>> +obj-$(CONFIG_USB_DWC3_AM62) += dwc3-am62.o
>>>>> obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
>>>>> obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
>>>>> obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
>>>>> diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c
>>>>> new file mode 100644
>>>>> index 000000000000..5700258c8deb
>>>>> --- /dev/null
>>>>> +++ b/drivers/usb/dwc3/dwc3-am62.c
>>>>> @@ -0,0 +1,446 @@
>>>>> +// SPDX-License-Identifier: GPL-2.0
>>>>> +/*
>>>>> + * dwc3-am62.c - TI specific Glue layer for AM62 DWC3 USB Controller
>>>>> + *
>>>>> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
>>>>> + */
>>>>> +
>>>>> +#include <linux/init.h>
>>>>> +#include <linux/interrupt.h>
>>>>> +#include <linux/irq.h>
>>>>> +#include <linux/kernel.h>
>>>>> +#include <linux/module.h>
>>>>> +#include <linux/platform_device.h>
>>>>> +#include <linux/workqueue.h>
>>>>> +#include <linux/mfd/syscon.h>
>>>>> +#include <linux/of.h>
>>>>> +#include <linux/of_device.h>
>>>>> +#include <linux/pm_runtime.h>
>>>>> +#include <linux/clk.h>
>>>>> +#include <linux/regmap.h>
>>>>> +#include <linux/devm-helpers.h>
>>>>> +#include <linux/pinctrl/consumer.h>
>>>>> +
>>>>> +/* USB WRAPPER register offsets */
>>>>> +#define USBSS_PID 0x0
>>>>> +#define USBSS_OVERCURRENT_CTRL 0x4
>>>>> +#define USBSS_PHY_CONFIG 0x8
>>>>> +#define USBSS_PHY_TEST 0xc
>>>>> +#define USBSS_CORE_STAT 0x14
>>>>> +#define USBSS_HOST_VBUS_CTRL 0x18
>>>>> +#define USBSS_MODE_CONTROL 0x1c
>>>>> +#define USBSS_WAKEUP_CONFIG 0x30
>>>>> +#define USBSS_WAKEUP_STAT 0x34
>>>>> +#define USBSS_OVERRIDE_CONFIG 0x38
>>>>> +#define USBSS_IRQ_MISC_STATUS_RAW 0x430
>>>>> +#define USBSS_IRQ_MISC_STATUS 0x434
>>>>> +#define USBSS_IRQ_MISC_ENABLE_SET 0x438
>>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR 0x43c
>>>>> +#define USBSS_IRQ_MISC_EOI 0x440
>>>>> +#define USBSS_INTR_TEST 0x490
>>>>> +#define USBSS_VBUS_FILTER 0x614
>>>>> +#define USBSS_VBUS_STAT 0x618
>>>>> +#define USBSS_DEBUG_CFG 0x708
>>>>> +#define USBSS_DEBUG_DATA 0x70c
>>>>> +#define USBSS_HOST_HUB_CTRL 0x714
>>>>> +
>>>>> +/* PHY CONFIG register bits */
>>>>> +#define USBSS_PHY_VBUS_SEL_MASK GENMASK(2, 1)
>>>>> +#define USBSS_PHY_VBUS_SEL_SHIFT 1
>>>>> +#define USBSS_PHY_LANE_REVERSE BIT(0)
>>>>> +
>>>>> +/* MODE CONTROL register bits */
>>>>> +#define USBSS_MODE_VALID BIT(0)
>>>>> +
>>>>> +/* WAKEUP CONFIG register bits */
>>>>> +#define USBSS_WAKEUP_CFG_OVERCURRENT_EN BIT(3)
>>>>> +#define USBSS_WAKEUP_CFG_LINESTATE_EN BIT(2)
>>>>> +#define USBSS_WAKEUP_CFG_SESSVALID_EN BIT(1)
>>>>> +#define USBSS_WAKEUP_CFG_VBUSVALID_EN BIT(0)
>>>>> +
>>>>> +/* WAKEUP STAT register bits */
>>>>> +#define USBSS_WAKEUP_STAT_OVERCURRENT BIT(4)
>>>>> +#define USBSS_WAKEUP_STAT_LINESTATE BIT(3)
>>>>> +#define USBSS_WAKEUP_STAT_SESSVALID BIT(2)
>>>>> +#define USBSS_WAKEUP_STAT_VBUSVALID BIT(1)
>>>>> +#define USBSS_WAKEUP_STAT_CLR BIT(0)
>>>>> +
>>>>> +/* IRQ_MISC_STATUS_RAW register bits */
>>>>> +#define USBSS_IRQ_MISC_RAW_VBUSVALID BIT(22)
>>>>> +#define USBSS_IRQ_MISC_RAW_SESSVALID BIT(20)
>>>>> +
>>>>> +/* IRQ_MISC_STATUS register bits */
>>>>> +#define USBSS_IRQ_MISC_VBUSVALID BIT(22)
>>>>> +#define USBSS_IRQ_MISC_SESSVALID BIT(20)
>>>>> +
>>>>> +/* IRQ_MISC_ENABLE_SET register bits */
>>>>> +#define USBSS_IRQ_MISC_ENABLE_SET_VBUSVALID BIT(22)
>>>>> +#define USBSS_IRQ_MISC_ENABLE_SET_SESSVALID BIT(20)
>>>>> +
>>>>> +/* IRQ_MISC_ENABLE_CLR register bits */
>>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR_VBUSVALID BIT(22)
>>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR_SESSVALID BIT(20)
>>>>> +
>>>>> +/* IRQ_MISC_EOI register bits */
>>>>> +#define USBSS_IRQ_MISC_EOI_VECTOR BIT(0)
>>>>> +
>>>>> +/* VBUS_STAT register bits */
>>>>> +#define USBSS_VBUS_STAT_SESSVALID BIT(2)
>>>>> +#define USBSS_VBUS_STAT_VBUSVALID BIT(0)
>>>>> +
>>>>> +/* Mask for PHY PLL REFCLK */
>>>>> +#define PHY_PLL_REFCLK_MASK GENMASK(3, 0)
>>>>> +
>>>>> +#define DWC3_AM62_AUTOSUSPEND_DELAY 100
>>>>> +
>>>>> +struct dwc3_data {
>>>>> + struct device *dev;
>>>>> + void __iomem *usbss;
>>>>> + struct clk *usb2_refclk;
>>>>> + struct work_struct work;
>>>>> + int vbus_irq;
>>>>> + int rate_code;
>>>>> + int connect;
>>>>> + struct regmap *syscon;
>>>>> + unsigned int offset;
>>>>> + unsigned int vbus_divider;
>>>>> +};
>>>>> +
>>>>> +static const int dwc3_ti_rate_table[] = { /* in KHZ */
>>>>> + 9600,
>>>>> + 10000,
>>>>> + 12000,
>>>>> + 19200,
>>>>> + 20000,
>>>>> + 24000,
>>>>> + 25000,
>>>>> + 26000,
>>>>> + 38400,
>>>>> + 40000,
>>>>> + 58000,
>>>>> + 50000,
>>>>> + 52000,
>>>>> +};
>>>>> +
>>>>> +static inline u32 dwc3_ti_readl(struct dwc3_data *data, u32 offset)
>>>>> +{
>>>>> + return readl((data->usbss) + offset);
>>>>> +}
>>>>> +
>>>>> +static inline void dwc3_ti_writel(struct dwc3_data *data, u32 offset, u32 value)
>>>>> +{
>>>>> + writel(value, (data->usbss) + offset);
>>>>> +}
>>>>> +
>>>>> +static void connect_detect_work(struct work_struct *work)
>>>>> +{
>>>>> + struct dwc3_data *data =
>>>>> + container_of(work, struct dwc3_data, work);
>>>>> + u32 vbus_state, reg;
>>>>> + int connect = 0;
>>>>> +
>>>>> + /* Read the status for VBUS valid register */
>>>>> + vbus_state = dwc3_ti_readl(data, USBSS_VBUS_STAT);
>>>>> + vbus_state &= USBSS_VBUS_STAT_VBUSVALID;
>>>>> +
>>>>> + if (vbus_state)
>>>>> + connect = 1;
>>>>> +
>>>>> + /* Set or clear mode valid bit based on connect or disconnect event */
>>>>> + if (data->connect != connect) {
>>>>> + reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
>>>>> + if (connect)
>>>>> + reg |= USBSS_MODE_VALID;
>>>>> + else
>>>>> + reg &= ~USBSS_MODE_VALID;
>>>>> +
>>>>> + dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
>>>>> + data->connect = connect;
>>>>> + }
>>>>> +}
>>>>> +
>>>>> +static irqreturn_t connect_detect_irq_handler(int irq, void *dev_id)
>>>>> +{
>>>>> + struct dwc3_data *data = dev_id;
>>>>> + u32 reg;
>>>>> +
>>>>> + /* Clear VBUS interrupt always to aviod queuing up redundant work items */
>>>>> + reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_STATUS);
>>>>> + reg |= USBSS_IRQ_MISC_VBUSVALID;
>>>>> + dwc3_ti_writel(data, USBSS_IRQ_MISC_STATUS, reg);
>>>>> +
>>>>> + queue_work(system_power_efficient_wq, &data->work);
>>>>> +
>>>>> + reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_EOI);
>>>>> + reg &= ~USBSS_IRQ_MISC_EOI_VECTOR;
>>>>> + dwc3_ti_writel(data, USBSS_IRQ_MISC_EOI, reg);
>>>>> + return IRQ_HANDLED;
>>>>> +}
>>>>> +
>>>>> +static int dwc3_ti_vbus_irq_setup(struct platform_device *pdev)
>>>>> +{
>>>>> + struct device *dev = &pdev->dev;
>>>>> + struct dwc3_data *data = platform_get_drvdata(pdev);
>>>>> + int irq, ret;
>>>>> +
>>>>> + /* Get the misc interrupt */
>>>>> + irq = platform_get_irq(pdev, 0);
>>>>> + if (irq < 0)
>>>>> + return irq;
>>>>> +
>>>>> + ret = devm_request_irq(dev, irq, connect_detect_irq_handler, IRQF_SHARED,
>>>>> + dev_name(dev), data);
>>>>> + if (ret) {
>>>>> + dev_err(dev, "failed to required IRQ #%d-->%d\n",
>>>>> + irq, ret);
>>>>> + return ret;
>>>>> + }
>>>>> +
>>>>> + data->vbus_irq = irq;
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +static int phy_syscon_pll_refclk(struct dwc3_data *data)
>>>>> +{
>>>>> + struct device *dev = data->dev;
>>>>> + struct device_node *node = dev->of_node;
>>>>> + struct of_phandle_args args;
>>>>> + struct regmap *syscon;
>>>>> + int ret;
>>>>> +
>>>>> + syscon = syscon_regmap_lookup_by_phandle(node, "ti,syscon-phy-pll-refclk");
>>>>> + if (IS_ERR(syscon)) {
>>>>> + dev_err(dev, "unable to get ti,syscon-phy-pll-refclk regmap\n");
>>>>> + return PTR_ERR(syscon);
>>>>> + }
>>>>> +
>>>>> + data->syscon = syscon;
>>>>> +
>>>>> + ret = of_parse_phandle_with_fixed_args(node, "ti,syscon-phy-pll-refclk", 1,
>>>>> + 0, &args);
>>>>> + if (ret)
>>>>> + return ret;
>>>>> +
>>>>> + data->offset = args.args[0];
>>>>> +
>>>>> + ret = regmap_update_bits(data->syscon, data->offset, PHY_PLL_REFCLK_MASK, data->rate_code);
>>>>> + if (ret) {
>>>>> + dev_err(dev, "failed to set phy pll reference clock rate\n");
>>>>> + return ret;
>>>>> + }
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +static void dwc3_ti_enable_irqs(struct dwc3_data *data)
>>>>> +{
>>>>> + u32 reg;
>>>>> +
>>>>> + /* enable VBUSVALID interrupt */
>>>>> + reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_ENABLE_SET);
>>>>> + reg |= USBSS_IRQ_MISC_ENABLE_SET_VBUSVALID;
>>>>> + dwc3_ti_writel(data, USBSS_IRQ_MISC_ENABLE_SET, reg);
>>>>> +}
>>>>> +
>>>>> +static void dwc3_ti_disable_irqs(struct dwc3_data *data)
>>>>> +{
>>>>> + u32 reg;
>>>>> +
>>>>> + /* disable VBUSVALID interrupt */
>>>>> + reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_ENABLE_CLR);
>>>>> + reg |= USBSS_IRQ_MISC_ENABLE_CLR_VBUSVALID;
>>>>> + dwc3_ti_writel(data, USBSS_IRQ_MISC_ENABLE_CLR, reg);
>>>>> +}
>>>>> +
>>>>> +static int dwc3_ti_probe(struct platform_device *pdev)
>>>>> +{
>>>>> + struct device *dev = &pdev->dev;
>>>>> + struct device_node *node = pdev->dev.of_node;
>>>>> + struct dwc3_data *data;
>>>>> + int i, ret;
>>>>> + unsigned long rate;
>>>>> + u32 reg;
>>>>> +
>>>>> + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
>>>>> + if (!data)
>>>>> + return -ENOMEM;
>>>>> +
>>>>> + data->dev = dev;
>>>>> + platform_set_drvdata(pdev, data);
>>>>> +
>>>>> + data->usbss = devm_platform_ioremap_resource(pdev, 0);
>>>>> + if (IS_ERR(data->usbss)) {
>>>>> + dev_err(dev, "can't map IOMEM resource\n");
>>>>> + return PTR_ERR(data->usbss);
>>>>> + }
>>>>> +
>>>>> + data->usb2_refclk = devm_clk_get(dev, "ref");
>>>>> + if (IS_ERR(data->usb2_refclk)) {
>>>>> + dev_err(dev, "can't get usb2_refclk\n");
>>>>> + return PTR_ERR(data->usb2_refclk);
>>>>> + }
>>>>> +
>>>>> + /* Calculate the rate code */
>>>>> + rate = clk_get_rate(data->usb2_refclk);
>>>>> + rate /= 1000; // To KHz
>>>>> + for (i = 0; i < ARRAY_SIZE(dwc3_ti_rate_table); i++) {
>>>>> + if (dwc3_ti_rate_table[i] == rate)
>>>>> + break;
>>>>> + }
>>>>> +
>>>>> + if (i == ARRAY_SIZE(dwc3_ti_rate_table)) {
>>>>> + dev_err(dev, "unsupported usb2_refclk rate: %lu KHz\n", rate);
>>>>> + ret = -EINVAL;
>>>>> + goto err_clk_disable;
>>>>> + }
>>>>> +
>>>>> + data->rate_code = i;
>>>>> +
>>>>> + /* Read the syscon property and set the rate code */
>>>>> + ret = phy_syscon_pll_refclk(data);
>>>>> + if (ret)
>>>>> + goto err_clk_disable;
>>>>> +
>>>>> + /* VBUS divider select */
>>>>> + data->vbus_divider = device_property_read_bool(dev, "ti,vbus-divider");
>>>>> + reg = dwc3_ti_readl(data, USBSS_PHY_CONFIG);
>>>>> + if (data->vbus_divider)
>>>>> + reg |= 1 << USBSS_PHY_VBUS_SEL_SHIFT;
>>>>> +
>>>>> + dwc3_ti_writel(data, USBSS_PHY_CONFIG, reg);
>>>>> +
>>>>> + /* Initialize a work queue */
>>>>> + ret = devm_work_autocancel(dev, &data->work, connect_detect_work);
>>>>> + if (ret)
>>>>> + goto err_clk_disable;
>>>>> +
>>>>> + /* Read and set VBUS IRQ */
>>>>> + ret = dwc3_ti_vbus_irq_setup(pdev);
>>>>> + if (ret)
>>>>> + goto err_clk_disable;
>>>>> +
>>>>> + pm_runtime_set_active(dev);
>>>>> + pm_runtime_enable(dev);
>>>>> + /*
>>>>> + * Don't ignore its dependencies with its children
>>>>> + */
>>>>> + pm_suspend_ignore_children(dev, false);
>>>>> + clk_prepare_enable(data->usb2_refclk);
>>>>> + pm_runtime_get_noresume(dev);
>>>>> +
>>>>> + ret = of_platform_populate(node, NULL, NULL, dev);
>>>>> + if (ret) {
>>>>> + dev_err(dev, "failed to create dwc3 core: %d\n", ret);
>>>>> + goto err_pm_disable;
>>>>> + }
>>>>> +
>>>>> + /* Enable vbus irq */
>>>>> + dwc3_ti_enable_irqs(data);
>>>>> +
>>>>> + connect_detect_work(&data->work);
>>>>> +
>>>>> + /* Setting up autosuspend */
>>>>> + pm_runtime_set_autosuspend_delay(dev, DWC3_AM62_AUTOSUSPEND_DELAY);
>>>>> + pm_runtime_use_autosuspend(dev);
>>>>> + pm_runtime_mark_last_busy(dev);
>>>>> + pm_runtime_put_autosuspend(dev);
>>>>> + return 0;
>>>>> +
>>>>> +err_pm_disable:
>>>>> + clk_disable_unprepare(data->usb2_refclk);
>>>>> + pm_runtime_disable(dev);
>>>>> + pm_runtime_set_suspended(dev);
>>>>> +err_clk_disable:
>>>>> + clk_put(data->usb2_refclk);
>>>>> + return ret;
>>>>> +}
>>>>> +
>>>>> +static int dwc3_ti_remove_core(struct device *dev, void *c)
>>>>> +{
>>>>> + struct platform_device *pdev = to_platform_device(dev);
>>>>> +
>>>>> + platform_device_unregister(pdev);
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +static int dwc3_ti_remove(struct platform_device *pdev)
>>>>> +{
>>>>> + struct device *dev = &pdev->dev;
>>>>> + struct dwc3_data *data = platform_get_drvdata(pdev);
>>>>> + u32 reg;
>>>>> +
>>>>> + dwc3_ti_disable_irqs(data);
>>>>> +
>>>>> + device_for_each_child(dev, NULL, dwc3_ti_remove_core);
>>>>> +
>>>>> + /* Clear mode valid bit */
>>>>> + reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
>>>>> + reg &= ~USBSS_MODE_VALID;
>>>>> + dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
>>>>> +
>>>>> + pm_runtime_put_sync(dev);
>>>>> + clk_disable_unprepare(data->usb2_refclk);
>>>>> + pm_runtime_disable(dev);
>>>>> + pm_runtime_set_suspended(dev);
>>>>> +
>>>>> + clk_put(data->usb2_refclk);
>>>>> + platform_set_drvdata(pdev, NULL);
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +#ifdef CONFIG_PM
>>>>> +static int dwc3_ti_suspend_common(struct device *dev)
>>>>> +{
>>>>> + struct dwc3_data *data = dev_get_drvdata(dev);
>>>>> +
>>>>> + /* disable irqs */
>>>>> + dwc3_ti_disable_irqs(data);
>>>>> +
>>>>> + clk_disable_unprepare(data->usb2_refclk);
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +static int dwc3_ti_resume_common(struct device *dev)
>>>>> +{
>>>>> + struct dwc3_data *data = dev_get_drvdata(dev);
>>>>> +
>>>>> + clk_prepare_enable(data->usb2_refclk);
>>>>> +
>>>>> + /* Enable irqs */
>>>>> + dwc3_ti_enable_irqs(data);
>>>>> +
>>>>> + return 0;
>>>>> +}
>>>>> +
>>>>> +static UNIVERSAL_DEV_PM_OPS(dwc3_ti_pm_ops, dwc3_ti_suspend_common,
>>>>> + dwc3_ti_resume_common, NULL);
>>>>> +
>>>>> +#define DEV_PM_OPS (&dwc3_ti_pm_ops)
>>>>> +#else
>>>>> +#define DEV_PM_OPS NULL
>>>>> +#endif /* CONFIG_PM */
>>>>> +
>>>>> +static const struct of_device_id dwc3_ti_of_match[] = {
>>>>> + { .compatible = "ti,am62-usb"},
>>>>> + {},
>>>>> +};
>>>>> +MODULE_DEVICE_TABLE(of, dwc3_ti_of_match);
>>>>> +
>>>>> +static struct platform_driver dwc3_ti_driver = {
>>>>> + .probe = dwc3_ti_probe,
>>>>> + .remove = dwc3_ti_remove,
>>>>> + .driver = {
>>>>> + .name = "dwc3-am62",
>>>>> + .pm = DEV_PM_OPS,
>>>>> + .of_match_table = dwc3_ti_of_match,
>>>>> + },
>>>>> +};
>>>>> +
>>>>> +module_platform_driver(dwc3_ti_driver);
>>>>> +
>>>>> +MODULE_ALIAS("platform:dwc3-am62");
>>>>> +MODULE_AUTHOR("Aswath Govindraju <a-govindraju@xxxxxx>");
>>>>> +MODULE_LICENSE("GPL");
>>>>> +MODULE_DESCRIPTION("DesignWare USB3 TI Glue Layer")
>>
>>

--
Thanks,
Aswath

Next message: Krzysztof Kozlowski: "Re: [PATCH] phy: samsung: fix missing of_node_put()"
Previous message: Vlad Buslov: "Re: [PATCH net-next v2] net: openvswitch: fix uAPI incompatibility with existing user space"
In reply to: Roger Quadros: "Re: [PATCH v3 2/2] drivers: usb: dwc3: Add AM62 USB wrapper driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]