Re: [PATCH v7 2/2] arm64: dts: qcom: sc7280: add lpass lpi pin controller node

[Matthias Kaehlcke]

On Mon, Apr 11, 2022 at 07:23:04PM +0530, Srinivasa Rao Mandadapu wrote:
> Add LPASS LPI pinctrl node required for Audio functionality on sc7280
> based platforms.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-idp.dtsi |  84 ++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280.dtsi     | 107 +++++++++++++++++++++++++++++++
>  2 files changed, 191 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> index 4ba2274..ea751dc 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> @@ -238,6 +238,90 @@
>  	modem-init;
>  };
>  
> +&dmic01 {

Shouldn't these nodes be in the PINCTRL section at their respective
positions in alphabetical order?

nit: since you are keeping the groups the group names are a bit generic IMO.
e.g. it is fairly obvious that 'dmic01_clk' refers to a clock pin, however
just 'dmic01' is a bit vague. You could consider adding the prefix 'lpass_'
to the group names for more clarity.

> +	clk {
> +		drive-strength = <8>;
> +	};
> +};
> +
> +&dmic01_sleep {
> +	clk {
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	data {
> +		pull-down;
> +	};
> +};
> +
> +&dmic23 {
> +	clk {
> +		drive-strength = <8>;
> +	};
> +};
> +
> +&dmic23_sleep {
> +	clk {
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	data {
> +		pull-down;
> +	};
> +};
> +
> +&rx_swr {
> +	clk {
> +		drive-strength = <2>;
> +		slew-rate = <1>;
> +		bias-disable;
> +	};
> +
> +	data {
> +		drive-strength = <2>;
> +		slew-rate = <1>;
> +		bias-bus-hold;
> +	};
> +};
> +
> +&rx_swr_sleep {
> +	clk {
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	data {
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +};
> +
> +&tx_swr {
> +	clk {
> +		drive-strength = <2>;
> +		slew-rate = <1>;
> +		bias-disable;
> +	};
> +
> +	data {
> +		slew-rate = <1>;
> +		bias-bus-hold;
> +	};
> +};
> +
> +&tx_swr_sleep {
> +	clk {
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	data {
> +		bias-bus-hold;
> +	};
> +};
> +
>  &pcie1 {
>  	status = "okay";
>  	perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 8099c80..c692420 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -1987,6 +1987,113 @@
>  			qcom,bcm-voters = <&apps_bcm_voter>;
>  		};
>  
> +		lpass_tlmm: pinctrl@33c0000 {
> +			compatible = "qcom,sc7280-lpass-lpi-pinctrl";
> +			reg = <0 0x033c0000 0x0 0x20000>,
> +				<0 0x03550000 0x0 0x10000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			gpio-ranges = <&lpass_tlmm 0 0 15>;
> +
> +			#clock-cells = <1>;
> +
> +			dmic01: dmic01 {
> +				clk {
> +					pins = "gpio6";

>From the schematics I interpret that the LPASS GPIOs 0-9 are mapped to the
SC7280 GPIOs 144-153. Is that correct?

> +					function = "dmic1_clk";
> +				};
> +
> +				data {
> +					pins = "gpio7";
> +					function = "dmic1_data";
> +				};
> +			};
> +
> +			dmic01_sleep: dmic01-sleep {
> +				clk {
> +					pins = "gpio6";
> +					function = "dmic1_clk";
> +				};
> +
> +				data {
> +					pins = "gpio7";
> +					function = "dmic1_data";
> +				};
> +			};
> +
> +			dmic23: dmic23 {
> +				clk {
> +					pins = "gpio8";
> +					function = "dmic2_clk";
> +				};
> +
> +				data {
> +					pins = "gpio9";
> +					function = "dmic2_data";
> +				};
> +			};
> +
> +			dmic23_sleep: dmic23_sleep {

s/dmic23_sleep/dmic23-sleep/ for the node name.

> +				clk {
> +					pins = "gpio8";
> +					function = "dmic2_clk";
> +				};
> +
> +				data {
> +					pins = "gpio9";
> +					function = "dmic2_data";
> +				};
> +			};
> +
> +			rx_swr: rx-swr {
> +				clk {
> +					pins = "gpio3";
> +					function = "swr_rx_clk";
> +				};
> +
> +				data {
> +					pins = "gpio4", "gpio5";
> +					function = "swr_rx_data";
> +				};
> +			};
> +
> +			rx_swr_sleep: rx-swr-sleep {
> +				clk {
> +					pins = "gpio3";
> +					function = "swr_rx_clk";
> +				};
> +
> +				data {
> +					pins = "gpio4", "gpio5";
> +					function = "swr_rx_data";
> +				};
> +			};
> +
> +			tx_swr: tx-swr {
> +				clk {
> +					pins = "gpio0";
> +					function = "swr_tx_clk";
> +				};
> +
> +				data {
> +					pins = "gpio1", "gpio2", "gpio14";
> +					function = "swr_tx_data";
> +				};
> +			};
> +
> +			tx_swr_sleep: tx-swr-sleep {
> +				clk {
> +					pins = "gpio0";
> +					function = "swr_tx_clk";
> +				};
> +
> +				data {
> +					pins = "gpio1", "gpio2", "gpio14";
> +					function = "swr_tx_data";
> +				};
> +			};
> +		};
> +
>  		gpu: gpu@3d00000 {
>  			compatible = "qcom,adreno-635.0", "qcom,adreno";
>  			reg = <0 0x03d00000 0 0x40000>,
> -- 
> 2.7.4
>