Re: [PATCH] amd_hsmp: Add HSMP protocol version 5 messages

[Carlos Bilbao]

On 4/11/2022 12:47 PM, Naveen Krishna Chatradhi wrote:
> From: Suma Hegde <suma.hegde@xxxxxxx>
> 
> HSMP protocol version 5 is supported on AMD family 19h model 10h
> EPYC processors. This version brings new features such as
> -- DIMM statistics
> -- Bandiwdth for IO and xGMI links

s/Bandiwdth/Bandwidth  

> -- Monitor socket and core frequency limits
> -- Configure power efficiency modes, df pstate range etc
> 
> Briefly, describe the new messages.

I think this line should go.

> 
> Signed-off-by: Suma Hegde <suma.hegde@xxxxxxx>
> Reviewed-by: Carlos Bilbao <carlos.bilbao@xxxxxxx>
> Signed-off-by: Naveen Krishna Chatradhi <nchatrad@xxxxxxx>
> ---
>  arch/x86/include/uapi/asm/amd_hsmp.h | 114 +++++++++++++++++++++++++--
>  1 file changed, 109 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/x86/include/uapi/asm/amd_hsmp.h b/arch/x86/include/uapi/asm/amd_hsmp.h
> index 7ee7ba0d63a3..769b939444ae 100644
> --- a/arch/x86/include/uapi/asm/amd_hsmp.h
> +++ b/arch/x86/include/uapi/asm/amd_hsmp.h
> @@ -31,9 +31,22 @@ enum hsmp_message_ids {
>  	HSMP_GET_CCLK_THROTTLE_LIMIT,	/* 10h Get CCLK frequency limit in socket */
>  	HSMP_GET_C0_PERCENT,		/* 11h Get average C0 residency in socket */
>  	HSMP_SET_NBIO_DPM_LEVEL,	/* 12h Set max/min LCLK DPM Level for a given NBIO */
> -					/* 13h Reserved */
> -	HSMP_GET_DDR_BANDWIDTH = 0x14,	/* 14h Get theoretical maximum and current DDR Bandwidth */
> -	HSMP_GET_TEMP_MONITOR,		/* 15h Get per-DIMM temperature and refresh rates */
> +	HSMP_GET_NBIO_DPM_LEVEL,	/* 13h Get LCLK DPM level min and max for a given NBIO */
> +	HSMP_GET_DDR_BANDWIDTH,		/* 14h Get theoretical maximum and current DDR Bandwidth */
> +	HSMP_GET_TEMP_MONITOR,		/* 15h Get socket temperature */
> +	HSMP_GET_DIMM_TEMP_RANGE,	/* 16h Get per-DIMM temperature range and refresh rate */
> +	HSMP_GET_DIMM_POWER,		/* 17h Get per-DIMM power consumption */
> +	HSMP_GET_DIMM_THERMAL,		/* 18h Get per-DIMM thermal sensors */
> +	HSMP_GET_SOCKET_FREQ_LIMIT,	/* 19h Get current active frequency per socket */
> +	HSMP_GET_CCLK_CORE_LIMIT,	/* 1Ah Get CCLK frequency limit per core */
> +	HSMP_GET_RAILS_SVI,		/* 1Bh Get SVI-based Telemetry for all rails */
> +	HSMP_GET_SOCKET_FMAX_FMIN,	/* 1Ch Get Fmax and Fmin per socket */
> +	HSMP_GET_IOLINK_BANDWITH,	/* 1Dh Get current bandwidth on IO Link */
> +	HSMP_GET_XGMI_BANDWITH,		/* 1Eh Get current bandwidth on xGMI Link */
> +	HSMP_SET_GMI3_WIDTH,		/* 1Fh Set max and min GMI3 Link width */
> +	HSMP_SET_PCI_RATE,		/* 20h Control link rate on PCIe devices */
> +	HSMP_SET_POWER_MODE,		/* 21h Select power efficiency profile policy */
> +	HSMP_SET_PSTATE_MAX_MIN,	/* 22h Set the max and min DF P-State  */
>  	HSMP_MSG_ID_MAX,
>  };
>  
> @@ -175,8 +188,12 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {
>  	 */
>  	{1, 0, HSMP_SET},
>  
> -	/* RESERVED message */
> -	{0, 0, HSMP_RSVD},
> +	/*
> +	 * HSMP_GET_NBIO_DPM_LEVEL, num_args = 1, response_sz = 1
> +	 * input: args[0] = nbioid[23:16]
> +	 * output: args[0] = max dpm level[15:8] + min dpm level[7:0]
> +	 */
> +	{1, 1, HSMP_GET},
>  
>  	/*
>  	 * HSMP_GET_DDR_BANDWIDTH, num_args = 0, response_sz = 1
> @@ -191,6 +208,93 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {
>  	 * [7:5] fractional part
>  	 */
>  	{0, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_DIMM_TEMP_RANGE, num_args = 1, response_sz = 1
> +	 * input: args[0] = DIMM address[7:0]
> +	 * output: args[0] = refresh rate[3] + temperature range[2:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_DIMM_POWER, num_args = 1, response_sz = 1
> +	 * input: args[0] = DIMM address[7:0]
> +	 * output: args[0] = DIMM power in mW[31:17] + update rate in ms[16:8] +
> +	 * DIMM address[7:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_DIMM_THERMAL, num_args = 1, response_sz = 1
> +	 * input: args[0] = DIMM address[7:0]
> +	 * output: args[0] = temperature in degree celcius[31:21] + update rate in ms[16:8] +
> +	 * DIMM address[7:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_SOCKET_FREQ_LIMIT, num_args = 0, response_sz = 1
> +	 * output: args[0] = frequency in MHz[31:16] + frequency source[15:0]
> +	 */
> +	{0, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_CCLK_CORE_LIMIT, num_args = 1, response_sz = 1
> +	 * input: args[0] = apic id [31:0]
> +	 * output: args[0] = frequency in MHz[31:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_RAILS_SVI, num_args = 0, response_sz = 1
> +	 * output: args[0] = power in mW[31:0]
> +	 */
> +	{0, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_SOCKET_FMAX_FMIN, num_args = 0, response_sz = 1
> +	 * output: args[0] = fmax in MHz[31:16] + fmin in MHz[15:0]
> +	 */
> +	{0, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_IOLINK_BANDWITH, num_args = 1, response_sz = 1
> +	 * input: args[0] = link id[15:8] + bw type[2:0]
> +	 * output: args[0] = io bandwidth in Mbps[31:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_GET_XGMI_BANDWITH, num_args = 1, response_sz = 1
> +	 * input: args[0] = link id[15:8] + bw type[2:0]
> +	 * output: args[0] = xgmi bandwidth in Mbps[31:0]
> +	 */
> +	{1, 1, HSMP_GET},
> +
> +	/*
> +	 * HSMP_SET_GMI3_WIDTH, num_args = 1, response_sz = 0
> +	 * input: args[0] = min link width[15:8] + max link width[7:0]
> +	 */
> +	{1, 0, HSMP_SET},
> +
> +	/*
> +	 * HSMP_SET_PCI_RATE, num_args = 1, response_sz = 1
> +	 * input: args[0] = link rate control value
> +	 * output: args[0] = previous link rate control value
> +	 */
> +	{1, 1, HSMP_SET},
> +
> +	/*
> +	 * HSMP_SET_POWER_MODE, num_args = 1, response_sz = 0
> +	 * input: args[0] = power efficiency mode[2:0]
> +	 */
> +	{1, 0, HSMP_SET},
> +
> +	/*
> +	 * HSMP_SET_PSTATE_MAX_MIN, num_args = 1, response_sz = 0
> +	 * input: args[0] = min df pstate[15:8] + max df pstate[7:0]
> +	 */
> +	{1, 0, HSMP_SET},
>  };
>  
>  /* Reset to default packing */

Other than that I stand by my Reviewed-by!

Thanks,
Carlos