Re: [PATCH 07/10] crypto: Use ARCH_DMA_MINALIGN instead of ARCH_KMALLOC_MINALIGN

[Ard Biesheuvel]

On Thu, 14 Apr 2022 at 16:53, Greg Kroah-Hartman
<gregkh@xxxxxxxxxxxxxxxxxxx> wrote:
>
> On Thu, Apr 14, 2022 at 04:36:46PM +0200, Ard Biesheuvel wrote:
> > On Thu, 14 Apr 2022 at 16:27, Greg Kroah-Hartman
> > <gregkh@xxxxxxxxxxxxxxxxxxx> wrote:
> > >
> > > On Thu, Apr 14, 2022 at 03:52:53PM +0200, Ard Biesheuvel wrote:
...
> > > > What we might do, given the fact that only inbound non-cache coherent
> > > > DMA is problematic, is dropping the kmalloc alignment to 8 like on
> > > > x86, and falling back to bounce buffering when a misaligned, non-cache
> > > > coherent inbound DMA mapping is created, using the SWIOTLB bounce
> > > > buffering code that we already have, and is already in use on most
> > > > affected systems for other reasons (i.e., DMA addressing limits)
> > >
> > > Ick, that's a mess.
> > >
> > > > This will cause some performance regressions, but in a way that seems
> > > > fixable to me: taking network drivers as an example, the RX buffers
> > > > that are filled using inbound DMA are typically owned by the driver
> > > > itself, which could be updated to round up its allocations and DMA
> > > > mappings. Block devices typically operate on quantities that are
> > > > aligned sufficiently already. In other cases, we will likely notice
> > > > if/when this fallback is taken on a hot path, but if we don't, at
> > > > least we know a bounce buffer is being used whenever we cannot perform
> > > > the DMA safely in-place.
> > >
> > > We can move to having an "allocator-per-bus" for memory like this to
> > > allow the bus to know if this is a DMA requirement or not.
> > >
> > > So for all USB drivers, we would have:
> > >         usb_kmalloc(size, flags);
> > > and then it might even be easier to verify with static tools that the
> > > USB drivers are sending only properly allocated data.  Same for SPI and
> > > other busses.
> > >
> >
> > As I pointed out earlier in the thread, alignment/padding requirements
> > for non-coherent DMA are a property of the CPU's cache hierarchy, not
> > of the device. So I'm not sure I follow how a per-subsystem
> > distinction would help here. In the case of USB especially, would that
> > mean that block, media and networking subsystems would need to be
> > aware of the USB-ness of the underlying transport?
>
> That's what we have required today, yes.  That's only because we knew
> that for some USB controllers, that was a requirement and we had no way
> of passing that information back up the stack so we just made it a
> requirement.
>
> But I do agree this is messy.  It's even messier for things like USB
> where it's not the USB device itself that matters, it's the USB
> controller that the USB device is attached to.  And that can be _way_ up
> the device hierarchy.  Attach something like a NFS mount over a PPP
> network connection on a USB to serial device and ugh, where do you
> begin?  :)
>

Exactly.

> And is this always just an issue of the CPU cache hierarchy?  And not the
> specific bridge that a device is connected to that CPU on?  Or am I
> saying the same thing here?
>

Yes, this is a system property not a device property, and the driver
typically doesn't have any knowledge of this. For example, if a PCI
host bridge happens to be integrated in a non-cache coherent way, any
PCI device plugged into it becomes non-coherent, and the associated
driver needs to do the right thing. This is why we rely on the DMA
layer to take care of this.

> I mean take a USB controller for example.  We could have a system where
> one USB controller is on a PCI bus, while another is on a "platform"
> bus.  Both of those are connected to the CPU in different ways and so
> could have different DMA rules.  Do we downgrade everything in the
> system for the worst connection possible?
>

No, we currently support a mix of coherent and non-coherent just fine,
and this shouldn't change. It's just that the mere fact that
non-coherent devices might exist is increasing the memory footprint of
all kmalloc allocations.

> Again, consider a USB driver allocating memory to transfer stuff, should
> it somehow know the cache hierarchy that it is connected to?  Right now
> we punt and do not do that at the expense of a bit of potentially
> wasted memory for small allocations.
>

This whole discussion is based on the premise that this is an expense
we would prefer to avoid. Currently, every kmalloc allocation is
rounded up to 128 bytes on arm64, while x86 uses only 8.