Re: [PATCH v2 5/7] arm64: dts: imx8mp: add the iMX8MP PCIe support

[Lucas Stach]

Am Montag, dem 07.03.2022 um 17:07 +0800 schrieb Richard Zhu:
> Add the i.MX8MP PCIe support.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/imx8mp.dtsi | 46 ++++++++++++++++++++++-
>  1 file changed, 45 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> index b40a5646f205..e7b3d8029e34 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/clock/imx8mp-clock.h>
>  #include <dt-bindings/power/imx8mp-power.h>
> +#include <dt-bindings/reset/imx8mp-reset.h>
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> @@ -375,7 +376,8 @@ iomuxc: pinctrl@30330000 {
>  			};
>  
>  			gpr: iomuxc-gpr@30340000 {
> -				compatible = "fsl,imx8mp-iomuxc-gpr", "syscon";
> +				compatible = "fsl,imx8mp-iomuxc-gpr",
> +					     "fsl,imx6q-iomuxc-gpr", "syscon";
>  				reg = <0x30340000 0x10000>;
>  			};
>  
> @@ -965,6 +967,17 @@ aips4: bus@32c00000 {
>  			#size-cells = <1>;
>  			ranges;
>  
> +			pcie_phy: pcie-phy@32f00000 {
> +				compatible = "fsl,imx8mp-pcie-phy";
> +				reg = <0x32f00000 0x10000>;
> +				resets = <&src IMX8MP_RESET_PCIEPHY>,
> +					 <&src IMX8MP_RESET_PCIEPHY_PERST>;
> +				reset-names = "pciephy", "perst";
> +				power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE_PHY>;
> +				#phy-cells = <0>;
> +				status = "disabled";
> +			};
> +	
>  			hsio_blk_ctrl: blk-ctrl@32f10000 {
>  				compatible = "fsl,imx8mp-hsio-blk-ctrl", "syscon";
>  				reg = <0x32f10000 0x24>;
> @@ -980,6 +993,37 @@ hsio_blk_ctrl: blk-ctrl@32f10000 {
>  			};
>  		};
>  
> +		pcie: pcie@33800000 {
> +			compatible = "fsl,imx8mp-pcie";
> +			reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>;
> +			reg-names = "dbi", "config";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			device_type = "pci";
> +			bus-range = <0x00 0xff>;
> +			ranges =  <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000 /* downstream I/O 64KB */
> +				   0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
> +			num-lanes = <1>;
> +			num-viewport = <4>;
> +			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> +			fsl,max-link-speed = <3>;

I believe that imx6_pcie_start_link does not properly handle Gen3
speeds.

Regards,
Lucas

> +			linux,pci-domain = <0>;
> +			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>;
> +			resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>,
> +				 <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>;
> +			reset-names = "apps", "turnoff";
> +			phys = <&pcie_phy>;
> +			phy-names = "pcie-phy";
> +			status = "disabled";
> +		};
> +
>  		gpu3d: gpu@38000000 {
>  			compatible = "vivante,gc";
>  			reg = <0x38000000 0x8000>;