[PATCH v12 4/4] arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

[Srinivasa Rao Mandadapu]

Add LPASS LPI pinctrl properties, which are required for Audio
functionality on herobrine based platforms of rev5+
(aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 84 +++++++++++++++++++++++
 1 file changed, 84 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index deaea3a..dfc42df 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -111,6 +111,90 @@ ap_ts_pen_1v8: &i2c13 {
  * - If a pin is not hooked up on Qcard, it gets no name.
  */
 
+&lpass_dmic01 {
+	clk {
+		drive-strength = <8>;
+	};
+};
+
+&lpass_dmic01_sleep {
+	clk {
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	data {
+		pull-down;
+	};
+};
+
+&lpass_dmic23 {
+	clk {
+		drive-strength = <8>;
+	};
+};
+
+&lpass_dmic23_sleep {
+	clk {
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	data {
+		pull-down;
+	};
+};
+
+&lpass_rx_swr {
+	clk {
+		drive-strength = <2>;
+		slew-rate = <1>;
+		bias-disable;
+	};
+
+	data {
+		drive-strength = <2>;
+		slew-rate = <1>;
+		bias-bus-hold;
+	};
+};
+
+&lpass_rx_swr_sleep {
+	clk {
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	data {
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&lpass_tx_swr {
+	clk {
+		drive-strength = <2>;
+		slew-rate = <1>;
+		bias-disable;
+	};
+
+	data {
+		slew-rate = <1>;
+		bias-bus-hold;
+	};
+};
+
+&lpass_tx_swr_sleep {
+	clk {
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	data {
+		bias-bus-hold;
+	};
+};
+
 &mi2s1_data0 {
 	drive-strength = <6>;
 	bias-disable;
-- 
2.7.4