[PATCH v2 01/17] dt-bindings: PCI: dwc: Define common and native DT bindings
From: Serge Semin
Date: Tue May 03 2022 - 17:47:20 EST
Currently both DW PCIe Root Port and End-point DT bindings are too generic
to be used as a descriptive set the device properties. Yes, it's very handy
to have them that way so the DT-schemas could be used to evaluate as many
DW PCIe-related DT-nodes as possible. But at the same time they don't
provide well defined DW PCIe RP/EP DT interface description thus leaving
too much flexibility for the new platforms, no encouraging the developers
to preserve a compatible interface. It causes having many
platform-specific DT bindings of the same generic properties.
Instead of currently implemented approach we suggest to be more
restrictive and yet preserve some level of flexibility in the DW PCIe
DT-bindings description. The device tree DT-schema is split up into
three parts: a common YAML-schema applicable for both DWC Root Port and
End-point controller configs, DWC PCIe Root Port-specific YAML-schema
and DWC PCIe End-point-specific YAML-schema, where
1) pci/snps,dw-pcie-common.yaml - the common DT-schema describes the most
generic constraints of the "reg", "interrupts", "clocks", "resets" and
"phys" properties together with a set of common for both device types
PCIe/AXI bus properties like a maximum number of lanes or a maximum link
speed, number of inbound and outbound iATU windows. In addition to that a
set of schema definitions declared under the "definitions" property with
"reg", "interrupt", "clock" and "reset" names common for DWC PCIe Root
Port and End-point devices. They can be used by the successive DT-schemas
in case they are supposed to be compatible with the generic DWC PCIe
controller DT-bindings.
2) pci/snps,dw-pcie.yaml, pci/snps,dw-pcie-ep.yaml - generic DW PCIe Root
Port and End-point DT-bindings which aside with the device-specific
properties set also contain more restrictive constraints. All new DW PCIe
platforms are supposed to be compatible with one of these bindings by
using "allOf: " property and additionally defining their own constraints
to close up the DT-bindings set.
So to speak in case if a DW PCIe-based device for some reason has too many
specific properties or it's bindings have already been defined in a
non-generic way, it's DT-schema is supposed to include 1) YAML-file and
provide its own constraints. Otherwise the ready-to-use bindings from 2)
should be utilized. There are only two DT-schemas compatible with 2) at the
moment are samsung,axynos-pcie.yaml and intel-gw-pcie.yaml. The
rest of the DW PCIe-related DT-schemas are supposed to use more generic
DW PCIe DT-bindings - pci/snps,dw-pcie-common.yaml.
Note the provided here generic properties and their possible values are
derived from the DW PCIe RC/EP hardware manuals and from the interface
implemented in the driver. The DT-bindings schemas are created to be as
full as possible with detailed properties/names description for the
easier interface comprehension and new platforms bindings development.
Also note since there are no generic DT-nodes can be found in the kernel
dts-es which would have a pure "snps,dw-pcie" compatible string, these
DT-bindings have been created to not be selected by default for
evaluation. They are supposed to be used by the new vendor-specific
DT-schemas to at least stop adding new bindings for the same set of DWC
PCIe signals or properties.
Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
---
If the '$defs' property is used instead of the 'definitions' one, the next
error will be spotted:
> DTC Documentation/devicetree/bindings/pci/snps,dw-pcie.example.dt.yaml
> CHECK Documentation/devicetree/bindings/pci/snps,dw-pcie.example.dt.yaml
> /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: reg-names:0: 'oneOf' conditional failed, one must be fixed:
> 'dbi' is not of type 'array'
> From schema: /.../snps,dw-pcie.yaml
> /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: reg-names:1: 'oneOf' conditional failed, one must be fixed:
> 'config' is not of type 'array'
> From schema: /.../snps,dw-pcie.yaml
> /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'anyOf' conditional failed, one must be fixed:
> /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'oneOf' conditional failed, one must be fixed:
> 'msi' is not of type 'array'
> /../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'oneOf' conditional failed, one must be fixed:
> 'msi' is not of type 'array'
> From schema: /.../snps,dw-pcie.yaml
The problem is caused by the 'def fixup_sub_schema()' method defined in
the dtschema parser. AFAIU It skips the sub-'$defs'-schemas evaluation thus
not having them fixed up properly. The next patch solves the denoted
problem:
--- a/lib.py 2022-04-23 19:51:38.829759258 +0300
+++ b/lib.py 2022-04-23 20:17:16.218137170 +0300
@@ -470,7 +470,7 @@
for subschema in v:
fixup_sub_schema(subschema, True)
- if k not in ['dependentRequired', 'dependentSchemas', 'dependencies', 'properties', 'patternProperties', '$defs']:
+ if k not in ['dependentRequired', 'dependentSchemas', 'dependencies', 'properties', 'patternProperties']:
continue
for prop in v:
The same effect can be reached just by using the 'definitions' property.
Since I don't know the original reasons of having the fixup skipped for
the '$defs' property, I decided to just take the later path and use the
'definitions' property in the DT schemas. Rob, it's up to you to decide
whether the dtschema parser needs to be fixed.
Changelog v2:
- Use 'definitions' property instead of the '$defs' one. It fixes the
dt-validate error: 'X is not of type array.'
- Drop 'interrupts' and 'interrupt-names' property from being required for
the native DW PCIe host.
- Evaluate the 'snps,dw-pcie-common.yaml' schema in the
'socionext,uniphier-pcie-ep.yaml' DT-bindings since the later has
platform-specific names defined.
---
.../bindings/pci/fsl,imx6q-pcie.yaml | 5 +-
.../bindings/pci/hisilicon,kirin-pcie.yaml | 4 +-
.../bindings/pci/sifive,fu740-pcie.yaml | 4 +-
.../bindings/pci/snps,dw-pcie-common.yaml | 306 ++++++++++++++++++
.../bindings/pci/snps,dw-pcie-ep.yaml | 143 +++++---
.../devicetree/bindings/pci/snps,dw-pcie.yaml | 189 +++++++----
.../pci/socionext,uniphier-pcie-ep.yaml | 2 +-
.../bindings/pci/toshiba,visconti-pcie.yaml | 2 +-
8 files changed, 532 insertions(+), 123 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
index 252e5b72aee0..541fb0b724ef 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -12,10 +12,11 @@ maintainers:
description: |+
This PCIe host controller is based on the Synopsys DesignWare PCIe IP
- and thus inherits all the common properties defined in snps,dw-pcie.yaml.
+ and thus inherits all the common properties defined in
+ snps,dw-pcie-common.yaml.
allOf:
- - $ref: /schemas/pci/snps,dw-pcie.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml b/Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml
index c9f04999c9cf..879d9ec41cb7 100644
--- a/Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml
@@ -14,10 +14,10 @@ description: |
Kirin PCIe host controller is based on the Synopsys DesignWare PCI core.
It shares common functions with the PCIe DesignWare core driver and
inherits common properties defined in
- Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
+ Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml.
allOf:
- - $ref: /schemas/pci/snps,dw-pcie.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml b/Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml
index 195e6afeb169..61b03f363196 100644
--- a/Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml
@@ -10,14 +10,14 @@ description: |+
SiFive FU740 PCIe host controller is based on the Synopsys DesignWare
PCI core. It shares common features with the PCIe DesignWare core and
inherits common properties defined in
- Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
+ Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml.
maintainers:
- Paul Walmsley <paul.walmsley@xxxxxxxxxx>
- Greentime Hu <greentime.hu@xxxxxxxxxx>
allOf:
- - $ref: /schemas/pci/snps,dw-pcie.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml
new file mode 100644
index 000000000000..6131ac737294
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml
@@ -0,0 +1,306 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/snps,dw-pcie-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DWC PCIe RP/EP controller
+
+maintainers:
+ - Jingoo Han <jingoohan1@xxxxxxxxx>
+ - Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx>
+
+properties:
+ reg:
+ description:
+ DWC PCIe CSR space is normally accessed over the dedicated Data Bus
+ Interface - DBI. In accordance with the reference manual the register
+ configuration space belongs to the Configuration-Dependent Module (CDM)
+ and is split up into several sub-parts Standard PCIe configuration
+ space, Port Logic Registers (PL), Shadow Config-space Registers,
+ iATU/eDMA registers. The particular sub-space is selected by the
+ CDM/ELBI (dbi_cs) and CS2 (dbi_cs2) signals (selector bits). Such
+ configuration provides a flexible interface for the system engineers to
+ either map the particular space at a desired MMIO address or just leave
+ them in a contiguous memory space if pure Native or AXI Bridge DBI access
+ is selected. Note the PCIe CFG-space, PL and Shadow registers are
+ specific to each activated function, while the rest of the sub-spaces
+ are common for all of them (if there are more than one).
+ minItems: 2
+ maxItems: 6
+
+ interrupts:
+ description:
+ There are two main sub-blocks which are normally capable of
+ generating interrupts. It's System Information Interface and MSI
+ interface. While the former one has some common for the Host and
+ End-point controllers IRQ-signals, the later interface is obviously
+ Root Complex specific since it's responsible for the incoming MSI
+ messages signalling. The System Information IRQ signals are mainly
+ responsible for reporting the generic PCIe hierarchy and Root
+ Complex events like VPD IO request, general AER, PME, Hot-plug, link
+ bandwidth change, link equalization request, INTx asserted/deasserted
+ Message detection, embedded DMA Tx/Rx/Error.
+ minItems: 1
+ maxItems: 26
+
+ clocks:
+ description:
+ DWC PCIe reference manual explicitly defines a set of the clocks required
+ to get the controller working correctly. In general all of them can
+ be divided into two groups':' application and core clocks. Note the
+ platforms may have some of the clock sources unspecified in case if the
+ corresponding domains are fed up from a common clock source.
+ minItems: 1
+ maxItems: 7
+
+ resets:
+ description:
+ DWC PCIe reference manual explicitly defines a set of the reset
+ signals required to be de-asserted to properly activate the controller
+ sub-parts. All of these signals can be divided into two sub-groups':'
+ application and core resets with respect to the main sub-domains they
+ are supposed to reset. Note the platforms may have some of these signals
+ unspecified in case if they are automatically handled or aggregated into
+ a comprehensive control module.
+ minItems: 1
+ maxItems: 10
+
+ reset-gpio:
+ deprecated: true
+ description:
+ Reference to the GPIO-controlled PERST# signal. It is used to reset all
+ the peripheral devices available on the PCIe bus.
+ maxItems: 1
+
+ reset-gpios:
+ description:
+ Reference to the GPIO-controlled PERST# signal. It is used to reset all
+ the peripheral devices available on the PCIe bus.
+ maxItems: 1
+
+ phys:
+ description:
+ There can be up to the number of possible lanes PHYs specified.
+ Obviously each specified PHY is supposed to be able to work in the
+ PCIe mode with a speed implied by the DWC PCIe controller it is
+ attached to.
+ minItems: 1
+ maxItems: 16
+
+ phy-names:
+ minItems: 1
+ maxItems: 16
+ items:
+ pattern: '^pcie([0-9]+|-?phy)?$'
+
+ num-lanes:
+ maximum: 16
+
+ max-link-speed:
+ maximum: 4
+
+ num-ob-windows:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+ description:
+ Number of outbound address translation windows. This parameter can be
+ auto-detected based on the iATU memory writability. So there is no
+ point in having a dedicated DT-property for it.
+ maximum: 256
+
+ num-ib-windows:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+ description:
+ Number of inbound address translation windows. In the same way as
+ for the outbound AT windows, this parameter can be auto-detected based
+ on the iATU memory writability. There is no point having a dedicated
+ DT-property for it either.
+ maximum: 256
+
+ num-viewport:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+ description:
+ Number of outbound view ports configured in hardware. It's the same as
+ the number of outbound AT windows.
+ maximum: 256
+
+ snps,enable-cdm-check:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Enable automatic checking of CDM (Configuration Dependent Module)
+ registers for data corruption. CDM registers include standard PCIe
+ configuration space registers, Port Logic registers, DMA and iATU
+ registers. This feature has been available since DWC PCIe v4.80a.
+
+additionalProperties: true
+
+definitions:
+ reg-names:
+ description:
+ CSR space names common for the DWC PCIe Root Port and End-point
+ controllers.
+ oneOf:
+ - description:
+ Basic DWC PCIe controller configuration-space accessible over
+ the DBI interface. This memory space is either activated with
+ CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region
+ with all spaces. Note iATU/eDMA CSRs are indirectly accessible
+ via the PL viewports on the DWC PCIe controllers older than
+ v4.80a.
+ const: dbi
+ - description:
+ Shadow DWC PCIe config-space registers. This space is selected
+ by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of
+ the PCI-SIG PCIe CFG-space with the shadow registers for some
+ PCI Header space, PCI Standard and Extended Structures. It's
+ mainly relevant for the end-point controller configuration,
+ but still there are some shadow registers available for the
+ Root Port mode too.
+ const: dbi2
+ - description:
+ External Local Bus registers. It's an application-dependent
+ registers normally defined by the platform engineers. The space
+ can be selected by setting CDM/ELBI = 1 and CS2 = 0 wires.
+ enum: [ elbi, appl, app, link ]
+ - description:
+ iATU/eDMA registers common for all device functions. It's an
+ unrolled memory space with the internal Address Translation
+ Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1
+ and CS2 = 1. For IP-core releases prior v4.80a, these registers
+ have been programmed via an indirect addressing scheme using a
+ set of viewport CSRs mapped into the PL space. Note iATU is
+ normally mapped to the 0x0 address of this region, while eDMA
+ is available at 0x80000 base address.
+ enum: [ atu, atu_dma ]
+ - description:
+ Platform-specific eDMA registers. Some platforms may have eDMA
+ CSRs mapped in non-standard base address. The registers offset
+ can be changed or the MS/LS-bits of the address can be added in
+ an additional RTL block before the MEM-IO transactions reach
+ the DW PCIe slave interface.
+ const: dma
+ - description:
+ Outbound iATU-available memory-region which usage scenario
+ depends on the DWC PCIe controller being either Root Port or
+ End-point. If it's Root Port then the register space shall
+ have the "config" name and it will be used to access the
+ peripheral PCIe devices configuration space. If it's PCIe
+ end-point controller, then the region shall be named as
+ "addr_space" and it will be used to generate various traffic
+ on the PCIe bus hierarchy. It's usage scenario depends on the
+ end-point functionality, for instance it can be used to create
+ MSI(X) messages.
+ enum: [ config, addr_space ]
+ - description:
+ PHY/PCS configuration registers. Some platforms can have the
+ PCS and PHY CSRs accessible over a dedicated memory mapped
+ region, but mainly these registers are indirectly accessible
+ either by means of the embedded PHY viewport schema or by some
+ platform-specific method.
+ enum: [ phy ]
+
+ interrupt-names:
+ description:
+ IRQ signal names common for the DWC PCIe Root Port and End-point
+ controllers.
+ oneOf:
+ - description:
+ Controller request to read or write virtual product data
+ from/to the VPD capability registers.
+ const: vpd
+ - description:
+ Link Equalization Request flag is set in the Link Status 2
+ register (applicable if the corresponding IRQ is enabled in
+ the Link Control 3 register).
+ const: l_eq
+ - description:
+ Indicates that the eDMA Tx/Rx transfer is complete or that an
+ error has occurred on the corresponding channel. eDMA can have
+ eight Tx (Write) and Rx (Read) eDMA channels thus supporting up
+ to 16 IRQ signals all together. Write eDMA channels shall go
+ first in the ordered row as per default edma_int[*] bus setup.
+ pattern: '^dma([0-9]|1[0-5])?$'
+ - description:
+ PCIe protocol correctable error or a Data Path protection
+ correctable error is detected by the automotive/safety
+ feature.
+ const: sft_ce
+ - description:
+ Indicates that the internal safety mechanism detected and
+ uncorrectable error.
+ const: sft_ue
+
+ clock-names:
+ description:
+ Reference clock names common for the DWC PCIe Root Port and End-point
+ controllers.
+ anyOf:
+ - description:
+ Data Bus Interface (DBI) clock. Clock signal for the AXI-bus
+ interface of the Configuration-Dependent Module, which is
+ basically the set of the controller CSRs.
+ enum: [ dbi, pcie ]
+ - description:
+ Application AXI-bus Master interface clock. Basically this is
+ a clock for the controller DMA interface (PCI-to-CPU).
+ enum: [ mstr, pcie_bus ]
+ - description:
+ Application AXI-bus Slave interface clock. This is a clock for
+ the CPU-to-PCI memory IO interface.
+ enum: [ slv, pcie_bus ]
+ - description:
+ Controller Core-PCS PIPE interface clock. It's normally
+ supplied by an external PCS-PHY.
+ const: pipe
+ - description:
+ Controller Primary clock. It's assumed that all controller input
+ signals (except resets) are synchronous to this clock.
+ const: core
+ - description:
+ Auxiliary clock for the controller PMC domain. The controller
+ partitioning implies having some parts to operate with this
+ clock in some power management states.
+ const: aux
+ - description:
+ Generic reference clock. In case if there are several
+ interfaces fed up with a common clock source it's advisable to
+ define it with this name (for instance pipe, core and aux can
+ be connected to a single source of the periodic signal).
+ const: ref
+ - description:
+ Clock for the PHY registers interface. Originally this is
+ a PHY-viewport-based interface, but some platform may have
+ specifically designed one.
+ const: phy_reg
+
+ reset-names:
+ description:
+ Reset signal names common for the DWC PCIe Root Port and End-point
+ controllers.
+ anyOf:
+ - description: Data Bus Interface (DBI) domain reset
+ const: dbi
+ - description: AXI-bus Master interface reset
+ const: mstr
+ - description: AXI-bus Slave interface reset
+ const: slv
+ - description: Controller Non-sticky CSR flags reset
+ const: non-sticky
+ - description: Controller sticky CSR flags reset
+ const: sticky
+ - description: PIPE-interface (Core-PCS) logic reset
+ const: pipe
+ - description:
+ Controller primary reset (resets everything except PMC module)
+ const: core
+ - description: PCS/PHY block reset
+ const: phy
+ - description: PMC hot reset signal
+ const: hot
+ - description: Cold reset signal
+ const: pwr
+
+...
diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
index e59059ab5be0..9e7b27bcf404 100644
--- a/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
@@ -13,74 +13,115 @@ maintainers:
description: |
Synopsys DesignWare PCIe host controller endpoint
+# Please create a separate DT-schema for the particular DWC PCIe End-point
+# controller and make sure it's assigned with the vendor-specific
+# compatible string together with the generic Synopsys DWC PCIe strings so
+# the bindings would be successfully evaluated against this schema.
+select: false
+
allOf:
- $ref: /schemas/pci/pci-ep.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
- anyOf:
- - {}
- - const: snps,dw-pcie-ep
+ contains:
+ oneOf:
+ - description:
+ DWC PCIe End-point controller (IP-core version is explicitly
+ specified in the additional compatible string)
+ items:
+ - pattern: '^snps,dw-pcie-ep-[0-9]+\.[0-9]+a?$'
+ - const: snps,dw-pcie-ep
+ - description:
+ DWC PCIe End-point controller (IP-core version is either unknown
+ or can be read from the PCIe version register of the PL reg-space)
+ const: snps,dw-pcie-ep
reg:
- description: |
- It should contain Data Bus Interface (dbi) and config registers for all
- versions.
- For designware core version >= 4.80, it may contain ATU address space.
- minItems: 2
- maxItems: 4
+ description:
+ DBI, DBI2 reg-spaces and outbound memory window are required for the
+ normal controller functioning. iATU memory IO region is also required
+ if the space is unrolled (IP-core version >= 4.80a).
+ minItems: 3
+ maxItems: 5
reg-names:
- minItems: 2
- maxItems: 4
+ minItems: 3
+ maxItems: 5
items:
- enum: [dbi, dbi2, config, atu, addr_space, link, atu_dma, appl]
-
- reset-gpio:
- description: GPIO pin number of PERST# signal
- maxItems: 1
- deprecated: true
-
- reset-gpios:
- description: GPIO controlled connection to PERST# signal
- maxItems: 1
-
- snps,enable-cdm-check:
- type: boolean
- description: |
- This is a boolean property and if present enables
- automatic checking of CDM (Configuration Dependent Module) registers
- for data corruption. CDM registers include standard PCIe configuration
- space registers, Port Logic registers, DMA and iATU (internal Address
- Translation Unit) registers.
-
- num-ib-windows:
- description: number of inbound address translation windows
- maxItems: 1
- deprecated: true
-
- num-ob-windows:
- description: number of outbound address translation windows
- maxItems: 1
- deprecated: true
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/reg-names
+ allOf:
+ - contains:
+ const: dbi
+ - contains:
+ const: dbi2
+ - contains:
+ const: addr_space
+
+ interrupts:
+ description:
+ There is no mandatory IRQ signals for the normal controller functioning,
+ but in addition to the native set the platforms may have a link- or
+ PM-related IRQs specified.
+ minItems: 1
+ maxItems: 20
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 20
+ items:
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/interrupt-names
+
+ clocks:
+ minItems: 1
+ maxItems: 7
+
+ clock-names:
+ minItems: 1
+ maxItems: 7
+ items:
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/clock-names
+
+ resets:
+ minItems: 1
+ maxItems: 10
+
+ reset-names:
+ minItems: 1
+ maxItems: 10
+ items:
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/reset-names
+
+ max-functions:
+ maximum: 32
required:
+ - compatible
- reg
- reg-names
- - compatible
additionalProperties: true
examples:
- |
- bus {
- #address-cells = <1>;
- #size-cells = <1>;
- pcie-ep@dfd00000 {
- compatible = "snps,dw-pcie-ep";
- reg = <0xdfc00000 0x0001000>, /* IP registers 1 */
- <0xdfc01000 0x0001000>, /* IP registers 2 */
- <0xd0000000 0x2000000>; /* Configuration space */
- reg-names = "dbi", "dbi2", "addr_space";
- };
+ pcie-ep@1f052000 {
+ compatible = "vendor,soc-pcie", "snps,dw-pcie-ep-4.60a", "snps,dw-pcie-ep";
+ reg = <0x66000000 0x1000>, <0x66010000 0x10000>, <0x67000000 0x400000>;
+ reg-names = "dbi", "dbi2", "addr_space";
+
+ clocks = <&sys_clk 12>, <&sys_clk 24>;
+ clock-names = "dbi", "ref";
+
+ resets = <&sys_rst 12>, <&sys_rst 24>;
+ reset-names = "dbi", "phy";
+
+ phys = <&pcie_phy>;
+ phy-names = "pcie-phy";
+
+ num-lanes = <4>;
+ max-link-speed = <4>;
+ num-ib-windows = <16>;
+ num-ob-windows = <16>;
};
+...
diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml
index a5345c494744..426dd9efe2cc 100644
--- a/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml
@@ -10,23 +10,39 @@ maintainers:
- Jingoo Han <jingoohan1@xxxxxxxxx>
- Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx>
-description: |
+description:
Synopsys DesignWare PCIe host controller
+# Please create a separate DT-schema for the particular DWC PCIe Root Port
+# controller and make sure it's assigned with the vendor-specific
+# compatible string together with the generic Synopsys DWC PCIe strings so
+# the bindings would be successfully evaluated against that schema.
+select: false
+
allOf:
- $ref: /schemas/pci/pci-bus.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
- anyOf:
- - {}
- - const: snps,dw-pcie
+ contains:
+ oneOf:
+ - description:
+ DWC PCIe Root Port controller (IP-core version is explicitly
+ specified in the additional compatible string)
+ items:
+ - pattern: '^snps,dw-pcie-[0-9]+\.[0-9]+a?$'
+ - const: snps,dw-pcie
+ - description:
+ DWC PCIe Root Port controller (IP-core version is either unknown
+ or can be read from the PCIe version register of the PL reg-space)
+ const: snps,dw-pcie
reg:
- description: |
- It should contain Data Bus Interface (dbi) and config registers for all
- versions.
- For designware core version >= 4.80, it may contain ATU address space.
+ description:
+ At least DBI reg-space and peripheral devices CFG-space outbound window
+ are required for the normal controller work. iATU memory IO region is
+ also required if the space is unrolled (IP-core version >= 4.80a).
minItems: 2
maxItems: 5
@@ -34,69 +50,114 @@ properties:
minItems: 2
maxItems: 5
items:
- enum: [ dbi, dbi2, config, atu, app, elbi, mgmt, ctrl, parf, cfg, link,
- ulreg, smu, mpu, apb, phy ]
-
- num-lanes:
- description: |
- number of lanes to use (this property should be specified unless
- the link is brought already up in firmware)
- maximum: 16
-
- reset-gpio:
- description: GPIO pin number of PERST# signal
- maxItems: 1
- deprecated: true
-
- reset-gpios:
- description: GPIO controlled connection to PERST# signal
- maxItems: 1
-
- interrupts: true
-
- interrupt-names: true
-
- clocks: true
-
- snps,enable-cdm-check:
- type: boolean
- description: |
- This is a boolean property and if present enables
- automatic checking of CDM (Configuration Dependent Module) registers
- for data corruption. CDM registers include standard PCIe configuration
- space registers, Port Logic registers, DMA and iATU (internal Address
- Translation Unit) registers.
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/reg-names
+ allOf:
+ - contains:
+ const: dbi
+ - contains:
+ const: config
+
+ interrupts:
+ description:
+ At least MSI interrupt signal is supposed to be specified for
+ the DWC PCIe host controller.
+ minItems: 1
+ maxItems: 26
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 26
+ items:
+ anyOf:
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/interrupt-names
+ - $ref: '#/definitions/interrupt-names'
+ allOf:
+ - contains:
+ const: msi
+
+ clocks:
+ minItems: 1
+ maxItems: 7
+
+ clock-names:
+ minItems: 1
+ maxItems: 7
+ items:
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/clock-names
- num-viewport:
- description: |
- number of view ports configured in hardware. If a platform
- does not specify it, the driver autodetects it.
- deprecated: true
+ resets:
+ minItems: 1
+ maxItems: 10
-additionalProperties: true
+ reset-names:
+ minItems: 1
+ maxItems: 10
+ items:
+ $ref: /schemas/pci/snps,dw-pcie-common.yaml#/definitions/reset-names
required:
+ - compatible
- reg
- reg-names
- - compatible
+
+additionalProperties: true
+
+definitions:
+ interrupt-names:
+ description:
+ DWC PCIe Root Port/Complex specific IRQ signal names.
+ oneOf:
+ - description:
+ DSP AXI MSI Interrupt detected. It gets de-asserted when there is
+ no more MSI interrupt pending. The interrupt is relevant to the
+ iMSI-RX - Integrated MSI Receiver (AXI bridge).
+ const: msi
+ - description:
+ Error condition detected and a bit is set in the Root Error Status
+ register of the AER capability. It's asserted when the RC
+ internally generated an error or an error message is received by
+ the RC.
+ const: aer
+ - description:
+ PME message is received by the port. That means having the PME
+ status bit set in the Root Status register (the event is
+ supposed to be unmasked in the Root Control register).
+ const: pme
+ - description:
+ Hot-plug event is detected. That is a bit has been set in the
+ Slot Status register and the corresponding event is enabled in
+ the Slot Control register.
+ const: hp
+ - description:
+ Link Autonomous Bandwidth Status flag has been set in the Link
+ Status register (the event is supposed to be unmasked in the
+ Link Control register).
+ const: bw_au
+ - description:
+ Bandwidth Management Status flag has been set in the Link
+ Status register (the event is supposed to be unmasked in the
+ Link Control register).
+ const: bw_mg
examples:
- |
- bus {
- #address-cells = <1>;
- #size-cells = <1>;
- pcie@dfc00000 {
- device_type = "pci";
- compatible = "snps,dw-pcie";
- reg = <0xdfc00000 0x0001000>, /* IP registers */
- <0xd0000000 0x0002000>; /* Configuration space */
- reg-names = "dbi", "config";
- #address-cells = <3>;
- #size-cells = <2>;
- ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000>,
- <0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>;
- interrupts = <25>, <24>;
- #interrupt-cells = <1>;
- num-lanes = <1>;
- };
+ pcie@1f052000 {
+ compatible = "vendor,soc-pcie", "snps,dw-pcie-4.60a", "snps,dw-pcie";
+ device_type = "pci";
+ reg = <0x1f052000 0x1000>, <0x1bdbf000 0x1000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x81000000 0 0x00000000 0x1bdb0000 0 0x00008000>,
+ <0x82000000 0 0x20000000 0x08000000 0 0x13db0000>;
+ bus-range = <0x0 0xff>;
+
+ interrupts = <0 80 4>;
+ interrupt-names = "msi";
+
+ reset-gpios = <&port0 0 1>;
+
+ num-lanes = <4>;
+ max-link-speed = <3>;
};
+...
diff --git a/Documentation/devicetree/bindings/pci/socionext,uniphier-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/socionext,uniphier-pcie-ep.yaml
index 437e61618d06..841eba762851 100644
--- a/Documentation/devicetree/bindings/pci/socionext,uniphier-pcie-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/socionext,uniphier-pcie-ep.yaml
@@ -16,7 +16,7 @@ maintainers:
- Kunihiko Hayashi <hayashi.kunihiko@xxxxxxxxxxxxx>
allOf:
- - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
index 30b6396d83c8..f0a3c436c6d1 100644
--- a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
@@ -13,7 +13,7 @@ description:
Toshiba Visconti5 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP.
allOf:
- - $ref: /schemas/pci/snps,dw-pcie.yaml#
+ - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
compatible:
--
2.35.1