Re: [PATCH v3 4/9] PCI/PM: Rework changing power states of PCI devices

[Rafael J. Wysocki]

On Tue, May 3, 2022 at 7:59 PM Nathan Chancellor <nathan@xxxxxxxxxx> wrote:
>
> Hi Rafael,
>
> On Thu, Apr 14, 2022 at 03:11:21PM +0200, Rafael J. Wysocki wrote:
> > From: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
> >
> > There are some issues related to changing power states of PCI
> > devices, mostly related to carrying out unnecessary actions in some
> > places, and the code is generally hard to follow.
> >
> >  1. pci_power_up() has two callers, pci_set_power_state() and
> >     pci_pm_default_resume_early().  The latter updates the current
> >     power state of the device right after calling pci_power_up()
> >     and it restores the entire config space of the device right
> >     after that, so pci_power_up() itself need not read the
> >     PCI_PM_CTRL register or restore the BARs after programming the
> >     device into D0 in that case.
> >
> >  2. It is generally hard to get a clear view of the pci_power_up()
> >     code flow, especially in some corner cases, due to all of the
> >     involved PCI_PM_CTRL register reads and writes occurring in
> >     pci_platform_power_transition() and in pci_raw_set_power_state(),
> >     some of which are redundant.
> >
> >  3. The transitions from low-power states to D0 and the other way
> >     around are unnecessarily tangled in pci_raw_set_power_state()
> >     which causes it to use a redundant local variable and makes it
> >     rather hard to follow.
> >
> > To address the above shortcomings, make the following changes:
> >
> >  a. Remove the code handling transitions into D0
> >     from pci_raw_set_power_state() and rename it as
> >     pci_set_low_power_state().
> >
> >  b. Add the code handling transitions into D0 directly
> >     to pci_power_up() and to a new wrapper function
> >     pci_set_full_power_state() calling it internally that is
> >     only used in pci_set_power_state().
> >
> >  c. Make pci_power_up() avoid redundant PCI_PM_CTRL register reads
> >     and make it work in the same way for transitions from any
> >     low-power states (transitions from D1 and D2 are handled
> >     slightly differently before the change).
> >
> >  d. Put the restoration of the BARs and the PCI_PM_CTRL
> >     register read confirming the power state change into
> >     pci_set_full_power_state() to avoid doing that in
> >     pci_pm_default_resume_early() unnecessarily.
> >
> > Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
> > Reviewed-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
>
> This change as commit 5bffe4c611f5 ("PCI/PM: Rework changing power
> states of PCI devices") causes my AMD-based system to fail to fully
> boot. As far as I can tell, this might be NVMe related, which might make
> getting a full log difficult, as journalctl won't have anywhere to save
> it. I see:
>
> nvme nvme0: I/O 8 QID 0 timeout, completion polled
>
> then shortly afterwards:
>
> nvme nvme0: I/O 24 QID 0 timeout, completion polled
> nvme nvme0: missing or invalid SUBNQN field
>
> then I am dropped into an emergency shell.

Thanks for the report!

> This is a log from the previous commit, which may give some hints about
> the configuration of this particular system.
>
> https://gist.github.com/nathanchance/8a56f0939410cb187896e904c72e41e7/raw/b47b2620bdd32d43c7a3b209fcfd9e3d4668f058/good-boot.log
>
> If there is any additional debugging information I can provide or
> patches I can try, please let me know!

Please see what happens if the "if (dev->current_state == PCI_D0)"
check and the following "return 0" statement in pci_power_up() are
commented out.