[PATCH v2 1/4] tpm: Add tpm_tis_i2c backend for tpm_tis_core

From: Johannes Holland
Date: Fri May 06 2022 - 13:03:37 EST

Next message: Johannes Holland: "[PATCH v2 2/4] tpm: Add tpm_tis_verify_crc to the tpm_tis_phy_ops protocol layer"
Previous message: Jaehee Park: "[PATCH v6] wfx: use container_of() to get vif"
Next in thread: Johannes Holland: "[PATCH v2 2/4] tpm: Add tpm_tis_verify_crc to the tpm_tis_phy_ops protocol layer"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Implement the TCG I2C Interface driver, as specified in the TCG PC
Client Platform TPM Profile (PTP) specification for TPM 2.0 v1.04
revision 14, section 8, I2C Interface Definition.

This driver supports Guard Times. That is, if required by the TPM, the
driver has to wait by a vendor-specific time after each I2C read/write.
The specific time is read from the TPM_I2C_INTERFACE_CAPABILITY register.

Unfortunately, the TCG specified almost but not quite compatible
register addresses. Therefore, the TIS register addresses need to be
mapped to I2C ones. The locality is stripped because for now, only
locality 0 is supported.

Add a sanity check to I2C reads of e.g. TPM_ACCESS and TPM_STS. This is
to detect communication errors and issues due to non-standard behaviour
(E.g. the clock stretching quirk in the BCM2835, see 4dbfb5f4401f). In
case the sanity check fails, attempt a retry.

The CRC over the FIFO register is not implemented here since a new call
has to be added to the API (tpm_tis_phy_ops).

Co-developed-by: Alexander Steffen <alexander.steffen@xxxxxxxxxxxx>
Signed-off-by: Alexander Steffen <alexander.steffen@xxxxxxxxxxxx>
Co-developed-by: Amir Mizinski <amirmizi6@xxxxxxxxx>
Signed-off-by: Amir Mizinski <amirmizi6@xxxxxxxxx>
Signed-off-by: Johannes Holland <johannes.holland@xxxxxxxxxxxx>
---
Changelog:
* v2:
* move CCs from copyright comment to commit message
* fix an unchecked return code

As discussed, kselftest runs successfully. However, it can time out.
I will fix this in a subsequent patch. Basically:

echo timeout=1500 > tools/testing/selftests/tpm2/settings

The line coverage for tpm_tis_i2c.c is 98.1%.

drivers/char/tpm/Kconfig | 12 ++
drivers/char/tpm/Makefile | 1 +
drivers/char/tpm/tpm_tis_i2c.c | 359 +++++++++++++++++++++++++++++++++
3 files changed, 372 insertions(+)
create mode 100644 drivers/char/tpm/tpm_tis_i2c.c

diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
index 4a5516406c22..927088b2c3d3 100644
--- a/drivers/char/tpm/Kconfig
+++ b/drivers/char/tpm/Kconfig
@@ -74,6 +74,18 @@ config TCG_TIS_SPI_CR50
If you have a H1 secure module running Cr50 firmware on SPI bus,
say Yes and it will be accessible from within Linux.

+config TCG_TIS_I2C
+ tristate "TPM Interface Specification 1.3 Interface / TPM 2.0 FIFO Interface - (I2C - generic)"
+ depends on I2C
+ select CRC_CCITT
+ select TCG_TIS_CORE
+ help
+ If you have a TPM security chip, compliant with the TCG TPM PTP
+ (I2C interface) specification and connected to an I2C bus master,
+ say Yes and it will be accessible from within Linux.
+ To compile this driver as a module, choose M here;
+ the module will be called tpm_tis_i2c.
+
config TCG_TIS_SYNQUACER
tristate "TPM Interface Specification 1.2 Interface / TPM 2.0 FIFO Interface (MMIO - SynQuacer)"
depends on ARCH_SYNQUACER || COMPILE_TEST
diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
index 66d39ea6bd10..0222b1ddb310 100644
--- a/drivers/char/tpm/Makefile
+++ b/drivers/char/tpm/Makefile
@@ -29,6 +29,7 @@ tpm_tis_spi-$(CONFIG_TCG_TIS_SPI_CR50) += tpm_tis_spi_cr50.o

obj-$(CONFIG_TCG_TIS_I2C_CR50) += tpm_tis_i2c_cr50.o

+obj-$(CONFIG_TCG_TIS_I2C) += tpm_tis_i2c.o
obj-$(CONFIG_TCG_TIS_I2C_ATMEL) += tpm_i2c_atmel.o
obj-$(CONFIG_TCG_TIS_I2C_INFINEON) += tpm_i2c_infineon.o
obj-$(CONFIG_TCG_TIS_I2C_NUVOTON) += tpm_i2c_nuvoton.o
diff --git a/drivers/char/tpm/tpm_tis_i2c.c b/drivers/char/tpm/tpm_tis_i2c.c
new file mode 100644
index 000000000000..34d12f78e7ab
--- /dev/null
+++ b/drivers/char/tpm/tpm_tis_i2c.c
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2014-2021 Nuvoton Technology corporation
+ * Copyright (C) 2019-2022 Infineon Technologies AG
+ *
+ * This device driver implements the TPM interface as defined in the TCG PC
+ * Client Platform TPM Profile (PTP) Specification for TPM 2.0 v1.04
+ * Revision 14.
+ *
+ * It is based on the tpm_tis_spi device driver.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/acpi.h>
+#include <linux/freezer.h>
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/tpm.h>
+#include "tpm_tis_core.h"
+
+/* TPM registers */
+#define TPM_I2C_LOC_SEL 0x00
+#define TPM_I2C_ACCESS 0x04
+#define TPM_I2C_INTERFACE_CAPABILITY 0x30
+#define TPM_I2C_DEVICE_ADDRESS 0x38
+#define TPM_I2C_DATA_CSUM_ENABLE 0x40
+#define TPM_I2C_DID_VID 0x48
+#define TPM_I2C_RID 0x4C
+
+/* TIS-compatible register address to avoid clash with TPM_ACCESS (0x00) */
+#define TPM_LOC_SEL 0x0FFF
+
+/* Mask to extract the I2C register from TIS register addresses */
+#define TPM_TIS_REGISTER_MASK 0x0FFF
+
+/*
+ * Guard Time:
+ * After each I2C operation, the TPM might require the master to wait.
+ * The time period is vendor-specific and must be read from the
+ * TPM_I2C_INTERFACE_CAPABILITY register.
+ *
+ * Before the Guard Time is read (or after the TPM failed to send an I2C NACK),
+ * a Guard Time of 250µs applies.
+ *
+ * Various flags in the same register indicate if a guard time is needed:
+ * - SR: <I2C read with repeated start> <guard time> <I2C read>
+ * - RR: <I2C read> <guard time> <I2C read>
+ * - RW: <I2C read> <guard time> <I2C write>
+ * - WR: <I2C write> <guard time> <I2C read>
+ * - WW: <I2C write> <guard time> <I2C write>
+ *
+ * See TCG PC Client PTP Specification v1.04, 8.1.10 GUARD_TIME
+ */
+
+/* Default Guard Time until interface capability register is read */
+#define GUARD_TIME_DEFAULT_MIN 250
+#define GUARD_TIME_DEFAULT_MAX 300
+
+/* Guard Time after I2C slave NACK */
+#define GUARD_TIME_ERR_MIN 250
+#define GUARD_TIME_ERR_MAX 300
+
+/* Guard Time bit masks; SR is repeated start, RW is read then write, etc. */
+#define TPM_GUARD_TIME_SR_MASK 0x40000000
+#define TPM_GUARD_TIME_RR_MASK 0x00100000
+#define TPM_GUARD_TIME_RW_MASK 0x00080000
+#define TPM_GUARD_TIME_WR_MASK 0x00040000
+#define TPM_GUARD_TIME_WW_MASK 0x00020000
+#define TPM_GUARD_TIME_MIN_MASK 0x0001FE00
+#define TPM_GUARD_TIME_MIN_SHIFT 9
+
+/* Masks with bits that must be read zero */
+#define TPM_ACCESS_READ_ZERO 0x48
+#define TPM_INT_ENABLE_ZERO 0x7FFFFF6
+#define TPM_STS_READ_ZERO 0x23
+#define TPM_INTF_CAPABILITY_ZERO 0x0FFFF000
+#define TPM_I2C_INTERFACE_CAPABILITY_ZERO 0x80000000
+
+struct tpm_tis_i2c_phy {
+ struct tpm_tis_data priv;
+ struct i2c_client *i2c_client;
+ bool guard_time_read;
+ bool guard_time_write;
+ u16 guard_time_min;
+ u16 guard_time_max;
+ u8 *io_buf;
+};
+
+static inline struct tpm_tis_i2c_phy *
+to_tpm_tis_i2c_phy(struct tpm_tis_data *data)
+{
+ return container_of(data, struct tpm_tis_i2c_phy, priv);
+}
+
+static u8 address_to_register(u32 addr)
+{
+ addr &= TPM_TIS_REGISTER_MASK;
+
+ switch (addr) {
+ case TPM_ACCESS(0):
+ return TPM_I2C_ACCESS;
+ case TPM_LOC_SEL:
+ return TPM_I2C_LOC_SEL;
+ case TPM_DID_VID(0):
+ return TPM_I2C_DID_VID;
+ case TPM_RID(0):
+ return TPM_I2C_RID;
+ default:
+ return addr;
+ }
+}
+
+static int retry_i2c_transfer_until_ack(struct tpm_tis_data *data,
+ struct i2c_msg *msg)
+{
+ struct tpm_tis_i2c_phy *phy = to_tpm_tis_i2c_phy(data);
+ bool guard_time;
+ int i = 0;
+ int ret;
+
+ if (msg->flags & I2C_M_RD)
+ guard_time = phy->guard_time_read;
+ else
+ guard_time = phy->guard_time_write;
+
+ do {
+ ret = i2c_transfer(phy->i2c_client->adapter, msg, 1);
+ if (ret < 0)
+ usleep_range(GUARD_TIME_ERR_MIN, GUARD_TIME_ERR_MAX);
+ else if (guard_time)
+ usleep_range(phy->guard_time_min, phy->guard_time_max);
+ /* retry on TPM NACK */
+ } while (ret < 0 && i++ < TPM_RETRY);
+
+ return ret;
+}
+
+/* Check that bits which must be read zero are not set */
+static int sanity_check_read(u8 reg, u16 len, u8 *buf)
+{
+ u32 value;
+ u32 zero_mask;
+
+ switch (len) {
+ case sizeof(u8):
+ value = buf[0];
+ break;
+ case sizeof(u16):
+ value = le16_to_cpup((__le16 *)buf);
+ break;
+ case sizeof(u32):
+ value = le32_to_cpup((__le32 *)buf);
+ break;
+ default:
+ return 0;
+ }
+
+ switch (reg) {
+ case TPM_I2C_ACCESS:
+ zero_mask = TPM_ACCESS_READ_ZERO;
+ break;
+ case TPM_INT_ENABLE(0) & TPM_TIS_REGISTER_MASK:
+ zero_mask = TPM_INT_ENABLE_ZERO;
+ break;
+ case TPM_STS(1) & TPM_TIS_REGISTER_MASK:
+ zero_mask = TPM_STS_READ_ZERO;
+ break;
+ case TPM_INTF_CAPS(0) & TPM_TIS_REGISTER_MASK:
+ zero_mask = TPM_INTF_CAPABILITY_ZERO;
+ break;
+ case TPM_I2C_INTERFACE_CAPABILITY:
+ zero_mask = TPM_I2C_INTERFACE_CAPABILITY_ZERO;
+ break;
+ default:
+ return 0;
+ }
+
+ if (unlikely((value & zero_mask) != 0x00)) {
+ pr_debug("TPM I2C read of register 0x%02x failed sanity check: 0x%x\n", reg, value);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int tpm_tis_i2c_read_bytes(struct tpm_tis_data *data, u32 addr, u16 len,
+ u8 *result, enum tpm_tis_io_mode io_mode)
+{
+ struct tpm_tis_i2c_phy *phy = to_tpm_tis_i2c_phy(data);
+ struct i2c_msg msg = { .addr = phy->i2c_client->addr };
+ u8 reg = address_to_register(addr);
+ int i = 0;
+ int ret;
+
+ do {
+ /* write register */
+ msg.len = sizeof(reg);
+ msg.buf = ®
+ msg.flags = 0;
+ ret = retry_i2c_transfer_until_ack(data, &msg);
+ if (ret < 0)
+ return ret;
+
+ /* read data */
+ msg.buf = result;
+ msg.len = len;
+ msg.flags = I2C_M_RD;
+ ret = retry_i2c_transfer_until_ack(data, &msg);
+ if (ret < 0)
+ return ret;
+
+ ret = sanity_check_read(reg, len, result);
+ if (ret == 0)
+ return 0;
+
+ usleep_range(GUARD_TIME_ERR_MIN, GUARD_TIME_ERR_MAX);
+ } while (i++ < TPM_RETRY);
+
+ return ret;
+}
+
+static int tpm_tis_i2c_write_bytes(struct tpm_tis_data *data, u32 addr, u16 len,
+ const u8 *value,
+ enum tpm_tis_io_mode io_mode)
+{
+ struct tpm_tis_i2c_phy *phy = to_tpm_tis_i2c_phy(data);
+ struct i2c_msg msg = { .addr = phy->i2c_client->addr };
+ u8 reg = address_to_register(addr);
+ int ret;
+
+ if (len > TPM_BUFSIZE - 1)
+ return -EIO;
+
+ /* write register and data in one go */
+ phy->io_buf[0] = reg;
+ memcpy(phy->io_buf + sizeof(reg), value, len);
+
+ msg.len = sizeof(reg) + len;
+ msg.buf = phy->io_buf;
+ ret = retry_i2c_transfer_until_ack(data, &msg);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int init_guard_time(struct tpm_tis_i2c_phy *phy)
+{
+ u32 i2c_caps;
+ int ret;
+
+ phy->guard_time_read = true;
+ phy->guard_time_write = true;
+ phy->guard_time_min = GUARD_TIME_DEFAULT_MIN;
+ phy->guard_time_max = GUARD_TIME_DEFAULT_MAX;
+
+ ret = tpm_tis_i2c_read_bytes(&phy->priv, TPM_I2C_INTERFACE_CAPABILITY,
+ sizeof(i2c_caps), (u8 *)&i2c_caps,
+ TPM_TIS_PHYS_32);
+ if (ret)
+ return ret;
+
+ phy->guard_time_read = (i2c_caps & TPM_GUARD_TIME_RR_MASK) ||
+ (i2c_caps & TPM_GUARD_TIME_RW_MASK);
+ phy->guard_time_write = (i2c_caps & TPM_GUARD_TIME_WR_MASK) ||
+ (i2c_caps & TPM_GUARD_TIME_WW_MASK);
+ phy->guard_time_min = (i2c_caps & TPM_GUARD_TIME_MIN_MASK) >>
+ TPM_GUARD_TIME_MIN_SHIFT;
+ /* guard_time_max = guard_time_min * 1.2 */
+ phy->guard_time_max = phy->guard_time_min + phy->guard_time_min / 5;
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(tpm_tis_pm, tpm_pm_suspend, tpm_tis_resume);
+
+static const struct tpm_tis_phy_ops tpm_i2c_phy_ops = {
+ .read_bytes = tpm_tis_i2c_read_bytes,
+ .write_bytes = tpm_tis_i2c_write_bytes,
+};
+
+static int tpm_tis_i2c_probe(struct i2c_client *dev,
+ const struct i2c_device_id *id)
+{
+ struct tpm_tis_i2c_phy *phy;
+ const u8 locality = 0;
+ int ret;
+
+ phy = devm_kzalloc(&dev->dev, sizeof(struct tpm_tis_i2c_phy),
+ GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->io_buf = devm_kzalloc(&dev->dev, TPM_BUFSIZE, GFP_KERNEL);
+ if (!phy->io_buf)
+ return -ENOMEM;
+
+ phy->i2c_client = dev;
+
+ /* must precede all communication with the tpm */
+ ret = init_guard_time(phy);
+ if (ret)
+ return ret;
+
+ ret = tpm_tis_i2c_write_bytes(&phy->priv, TPM_LOC_SEL, sizeof(locality),
+ &locality, TPM_TIS_PHYS_8);
+ if (ret)
+ return ret;
+
+ return tpm_tis_core_init(&dev->dev, &phy->priv, -1, &tpm_i2c_phy_ops,
+ NULL);
+}
+
+static int tpm_tis_i2c_remove(struct i2c_client *client)
+{
+ struct tpm_chip *chip = i2c_get_clientdata(client);
+
+ tpm_chip_unregister(chip);
+ tpm_tis_remove(chip);
+ return 0;
+}
+
+static const struct i2c_device_id tpm_tis_i2c_id[] = {
+ { "tpm_tis_i2c", 0 },
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, tpm_tis_i2c_id);
+
+static const struct of_device_id of_tis_i2c_match[] = {
+ { .compatible = "infineon,slb9673", },
+ { .compatible = "tcg,tpm-tis-i2c", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, of_tis_i2c_match);
+
+static struct i2c_driver tpm_tis_i2c_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "tpm_tis_i2c",
+ .pm = &tpm_tis_pm,
+ .of_match_table = of_match_ptr(of_tis_i2c_match),
+ },
+ .probe = tpm_tis_i2c_probe,
+ .remove = tpm_tis_i2c_remove,
+ .id_table = tpm_tis_i2c_id,
+};
+module_i2c_driver(tpm_tis_i2c_driver);
+
+MODULE_DESCRIPTION("TPM Driver for native I2C access");
+MODULE_LICENSE("GPL");
--
2.34.1

Next message: Johannes Holland: "[PATCH v2 2/4] tpm: Add tpm_tis_verify_crc to the tpm_tis_phy_ops protocol layer"
Previous message: Jaehee Park: "[PATCH v6] wfx: use container_of() to get vif"
Next in thread: Johannes Holland: "[PATCH v2 2/4] tpm: Add tpm_tis_verify_crc to the tpm_tis_phy_ops protocol layer"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]