Re: [PATCH v4 12/23] ata: libahci: Extend port-cmd flags set with port capabilities

[Serge Semin]

On Tue, Jun 14, 2022 at 05:32:41PM +0900, Damien Le Moal wrote:
> On 6/10/22 17:17, Serge Semin wrote:
> > Currently not all of the Port-specific capabilities listed in the
> 
> s/listed/are listed
> 
> > PORT_CMD-enumeration. Let's extend that set with the Cold Presence
> > Detection and Mechanical Presence Switch attached to the Port flags [1] so
> > to closeup the set of the platform-specific port-capabilities flags.  Note
> > these flags are supposed to be set by the platform firmware if there is
> > one. Alternatively as we are about to do they can be set by means of the
> > OF properties.
> > 
> > While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DMPS and fix the
> > comment there. In accordance with [2] that IRQ flag is supposed to
> > indicate the state of the signal coming from the Mechanical Presence
> > Switch.
> > 
> > [1] Serial ATA AHCI 1.3.1 Specification, p.27
> > [2] Serial ATA AHCI 1.3.1 Specification, p.24, p.88
> > 
> > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > Reviewed-by: Hannes Reinecke <hare@xxxxxxx>
> > 
> > ---
> > 
> > Changelog v4:
> > - Fix the DMPS macros name in the patch log. (@Sergei Shtylyov)
> > ---
> >  drivers/ata/ahci.h | 7 ++++++-
> >  1 file changed, 6 insertions(+), 1 deletion(-)
> > 
> > diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
> > index 7d834deefeb9..f501531bd1b3 100644
> > --- a/drivers/ata/ahci.h
> > +++ b/drivers/ata/ahci.h
> > @@ -138,7 +138,7 @@ enum {
> >  	PORT_IRQ_BAD_PMP	= (1 << 23), /* incorrect port multiplier */
> >  
> >  	PORT_IRQ_PHYRDY		= (1 << 22), /* PhyRdy changed */
> > -	PORT_IRQ_DEV_ILCK	= (1 << 7), /* device interlock */
> > +	PORT_IRQ_DMPS		= (1 << 7), /* mechanical presence status */
> >  	PORT_IRQ_CONNECT	= (1 << 6), /* port connect change status */
> >  	PORT_IRQ_SG_DONE	= (1 << 5), /* descriptor processed */
> >  	PORT_IRQ_UNK_FIS	= (1 << 4), /* unknown FIS rx'd */
> > @@ -166,6 +166,8 @@ enum {
> >  	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
> >  	PORT_CMD_FBSCP		= (1 << 22), /* FBS Capable Port */
> >  	PORT_CMD_ESP		= (1 << 21), /* External Sata Port */
> > +	PORT_CMD_CPD		= (1 << 20), /* Cold Presence Detection */
> > +	PORT_CMD_MPSP		= (1 << 19), /* Mechanical Presence Switch */
> >  	PORT_CMD_HPCP		= (1 << 18), /* HotPlug Capable Port */
> >  	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
> >  	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
> > @@ -181,6 +183,9 @@ enum {
> >  	PORT_CMD_ICC_PARTIAL	= (0x2 << 28), /* Put i/f in partial state */
> >  	PORT_CMD_ICC_SLUMBER	= (0x6 << 28), /* Put i/f in slumber state */
> >  
> > +	PORT_CMD_CAP		= PORT_CMD_HPCP | PORT_CMD_MPSP |
> > +				  PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP,
> 

> What is this one for ? A comment above it would be nice.

Isn't it obviously inferrable from the definition and the item name?

-Sergey

> 
> > +
> >  	/* PORT_FBS bits */
> >  	PORT_FBS_DWE_OFFSET	= 16, /* FBS device with error offset */
> >  	PORT_FBS_ADO_OFFSET	= 12, /* FBS active dev optimization offset */
> 
> 
> -- 
> Damien Le Moal
> Western Digital Research