Re: [PATCH v5 1/9] mm/demotion: Add support for explicit memory tiers

From: Huang, Ying
Date: Sun Jun 19 2022 - 21:56:16 EST


Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> writes:

> On Thu, 16 Jun 2022 09:11:24 +0800
> Ying Huang <ying.huang@xxxxxxxxx> wrote:
>
>> On Tue, 2022-06-14 at 14:56 -0400, Johannes Weiner wrote:
>> > On Tue, Jun 14, 2022 at 01:31:37PM +0530, Aneesh Kumar K V wrote:
>> > > On 6/13/22 9:20 PM, Johannes Weiner wrote:
>> > > > On Mon, Jun 13, 2022 at 07:53:03PM +0530, Aneesh Kumar K V wrote:
>> > > > > If the kernel still can't make the right decision, userspace could rearrange
>> > > > > them in any order using rank values. Without something like rank, if
>> > > > > userspace needs to fix things up, it gets hard with device
>> > > > > hotplugging. ie, the userspace policy could be that any new PMEM tier device
>> > > > > that is hotplugged, park it with a very low-rank value and hence lowest in
>> > > > > demotion order by default. (echo 10 >
>> > > > > /sys/devices/system/memtier/memtier2/rank) . After that userspace could
>> > > > > selectively move the new devices to the correct memory tier?
>> > > >
>> > > > I had touched on this in the other email.
>> > > >
>> > > > This doesn't work if two drivers that should have separate policies
>> > > > collide into the same tier - which is very likely with just 3 tiers.
>> > > > So it seems to me the main usecase for having a rank tunable falls
>> > > > apart rather quickly until tiers are spaced out more widely. And it
>> > > > does so at the cost of an, IMO, tricky to understand interface.
>> > > >
>> > >
>> > > Considering the kernel has a static map for these tiers, how can two drivers
>> > > end up using the same tier? If a new driver is going to manage a memory
>> > > device that is of different characteristics than the one managed by dax/kmem,
>> > > we will end up adding
>> > >
>> > > #define MEMORY_TIER_NEW_DEVICE 4
>> > >
>> > > The new driver will never use MEMORY_TIER_PMEM
>> > >
>> > > What can happen is two devices that are managed by DAX/kmem that
>> > > should be in two memory tiers get assigned the same memory tier
>> > > because the dax/kmem driver added both the device to the same memory tier.
>> > >
>> > > In the future we would avoid that by using more device properties like HMAT
>> > > to create additional memory tiers with different rank values. ie, we would
>> > > do in the dax/kmem create_tier_from_rank() .
>> >
>> > Yes, that's the type of collision I mean. Two GPUs, two CXL-attached
>> > DRAMs of different speeds etc.
>> >
>> > I also like Huang's idea of using latency characteristics instead of
>> > abstract distances. Though I'm not quite sure how feasible this is in
>> > the short term, and share some concerns that Jonathan raised. But I
>> > think a wider possible range to begin with makes sense in any case.
>> >
>> > > > In the other email I had suggested the ability to override not just
>> > > > the per-device distance, but also the driver default for new devices
>> > > > to handle the hotplug situation.
>> > > >
>> > >
>> > > I understand that the driver override will be done via module parameters.
>> > > How will we implement device override? For example in case of dax/kmem driver
>> > > the device override will be per dax device? What interface will we use to set the override?
>> > >
>> > > IIUC in the above proposal the dax/kmem will do
>> > >
>> > > node_create_and_set_memory_tier(numa_node, get_device_tier_index(dev_dax));
>> > >
>> > > get_device_tier_index(struct dev_dax *dev)
>> > > {
>> > >  return dax_kmem_tier_index; // module parameter
>> > > }
>> > >
>> > > Are you suggesting to add a dev_dax property to override the tier defaults?
>> >
>> > I was thinking a new struct memdevice and struct memtype(?). Every
>> > driver implementing memory devices like this sets those up and
>> > registers them with generic code and preset parameters. The generic
>> > code creates sysfs directories and allows overriding the parameters.
>> >
>> > struct memdevice {
>> > struct device dev;
>> > unsigned long distance;
>> > struct list_head siblings;
>> > /* nid? ... */
>> > };
>> >
>> > struct memtype {
>> > struct device_type type;
>> > unsigned long default_distance;
>> > struct list_head devices;
>> > };
>> >
>> > That forms the (tweakable) tree describing physical properties.
>>
>> In general, I think memtype is a good idea. I have suggested
>> something similar before. It can describe the characters of a
>> specific type of memory (same memory media with different interface
>> (e.g., CXL, or DIMM) will be different memory types). And they can
>> be used to provide overriding information.
> I'm not sure you are suggesting interface as one element of distinguishing
> types, or as the element - just in case it's as 'the element'.
> Ignore the next bit if not ;)
>
> Memory "interface" isn't going to be enough of a distinction. If you want to have
> a default distance it would need to be different for cases where the
> same 'type' of RAM has very different characteristics. Applies everywhere
> but given CXL 'defines' a lot of this - if we just have DRAM attached
> via CXL:
>
> 1. 16-lane direct attached DRAM device. (low latency - high bw)
> 2. 4x 16-lane direct attached DRAM interleaved (low latency - very high bw)
> 3. 4-lane direct attached DRAM device (low latency - low bandwidth)
> 4. 16-lane to single switch, 4x 4-lane devices interleaved (mid latency - high bw)
> 5. 4-lane to single switch, 4x 4-lane devices interleaved (mid latency, mid bw)
> 6. 4x 16-lane so 4 switch, each switch to 4 DRAM devices (mid latency, very high bw)
> (7. 16 land directed attached nvram. (midish latency, high bw - perf wise might be
> similarish to 4).
>
> It could be a lot more complex, but hopefully that conveys that 'type'
> is next to useless to characterize things unless we have a very large number
> of potential subtypes. If we were on current tiering proposal
> we'd just have the CXL subsystem manage multiple tiers to cover what is
> attached.

Thanks for detailed explanation. I learned a lot from you. Yes,
interface itself isn't enough to character the memory devices. We need
more fine-grained way to do that. But anyway, I think that it's better
to identify this via BIOS or kernel instead of user space.

So the kernel drivers will

- group the memory devices enumerated into memory types

- provide latency/bandwidth or distance information for each memory type

Then user space may determine the policy via adjusting the
latency/bandwidth or distance and/or the tiering granularity.

Best Regards,
Huang, Ying

>>
>> As for memdevice, I think that we already have "node" to represent
>> them in sysfs. Do we really need another one? Is it sufficient to
>> add some links to node in the appropriate directory? For example,
>> make memtype class device under the physical device (e.g. CXL device),
>> and create links to node inside the memtype class device directory?
>>
>> > From that, the kernel then generates the ordered list of tiers.
>>
>> As Jonathan Cameron pointed, we may need the memory tier ID to be
>> stable if possible. I know this isn't a easy task. At least we can
>> make the default memory tier (CPU local DRAM) ID stable (for example
>> make it always 128)? That provides an anchor for users to understand.
>>
>> Best Regards,
>> Huang, Ying
>>
>> > > > This should be less policy than before. Driver default and per-device
>> > > > distances (both overridable) combined with one tunable to set the
>> > > > range of distances that get grouped into tiers.
>> > > >
>> > >
>> > > Can you elaborate more on how distance value will be used? The device/device NUMA node can have
>> > > different distance value from other NUMA nodes. How do we group them?
>> > > for ex: earlier discussion did outline three different topologies. Can you
>> > > ellaborate how we would end up grouping them using distance?
>> > >
>> > > For ex: in the topology below node 2 is at distance 30 from Node0 and 40 from Nodes
>> > > so how will we classify node 2?
>> > >
>> > >
>> > > Node 0 & 1 are DRAM nodes, node 2 & 3 are PMEM nodes.
>> > >
>> > > 20
>> > > Node 0 (DRAM) ---- Node 1 (DRAM)
>> > >  | \ / |
>> > >  | 30 40 X 40 | 30
>> > >  | / \ |
>> > > Node 2 (PMEM) ---- Node 3 (PMEM)
>> > > 40
>> > >
>> > > node distances:
>> > > node 0 1 2 3
>> > > 0 10 20 30 40
>> > > 1 20 10 40 30
>> > > 2 30 40 10 40
>> > > 3 40 30 40 10
>> >
>> > I'm fairly confused by this example. Do all nodes have CPUs? Isn't
>> > this just classic NUMA, where optimizing for locality makes the most
>> > sense, rather than tiering?
>> >
>> > Forget the interface for a second, I have no idea how tiering on such
>> > a system would work. One CPU's lower tier can be another CPU's
>> > toptier. There is no lowest rung from which to actually *reclaim*
>> > pages. Would the CPUs just demote in circles?
>> >
>> > And the coldest pages on one socket would get demoted into another
>> > socket and displace what that socket considers hot local memory?
>> >
>> > I feel like I missing something.
>> >
>> > When we're talking about tiered memory, I'm thinking about CPUs
>> > utilizing more than one memory node. If those other nodes have CPUs,
>> > you can't reliably establish a singular tier order anymore and it
>> > becomes classic NUMA, no?
>>
>>