Re: [PATCH v3] USB: serial: option: add Quectel EM05-G modem

[Johan Hovold]

On Tue, Jun 21, 2022 at 07:59:43PM +0800, Yonglin Tan wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
> 
> "RMNET"	: AT + DIAG + NMEA + Modem + QMI
> "MBIM"	: MBIM + AT + DIAG + NMEA + Modem
> 
> The detailed description of the USB configuration for each mode as follows:
> 
> RMNET Mode
> --------------
> T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
> D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
> P:  Vendor=2c7c ProdID=030a Rev= 3.18
> S:  Manufacturer=Quectel
> S:  Product=Quectel EM05-G
> C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
> E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> 
> MBIM Mode
> --------------
> T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
> D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
> P:  Vendor=2c7c ProdID=030a Rev= 3.18
> S:  Manufacturer=Quectel
> S:  Product=Quectel EM05-G
> C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
> A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
> E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
> E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
> I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> 
> Signed-off-by: Yonglin Tan <yonglin.tan@xxxxxxxxxxx>
> ---
> V2:
>  1. Add the description of the usb interface configurations.
>  2. Add QMI Interface description.
> 
> V3:
>  1. Move the entry to where the other Quectel entries with numerical PIDs are.
>  2. Define the macro and remove the comment.

I meant to just move the entry where the other entries that use
numerical PIDs (instead of defines) are. But this works too.

>  drivers/usb/serial/option.c | 3 +++
>  1 file changed, 3 insertions(+)
>  mode change 100644 => 100755 drivers/usb/serial/option.c

You're still trying to change the permission bits of the file here,
though.

You need to figure out why this happens yourself. But I can't accept the
patch before this is fixed.

You could try chmod 644 before committing, but that may not be
sufficient.

> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> old mode 100644
> new mode 100755
> index ed1e50d..7b52865
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -252,6 +252,7 @@ static void option_instat_callback(struct urb *urb);
>  #define QUECTEL_PRODUCT_EG95			0x0195
>  #define QUECTEL_PRODUCT_BG96			0x0296
>  #define QUECTEL_PRODUCT_EP06			0x0306
> +#define QUECTEL_PRODUCT_EM05G			0x030a
>  #define QUECTEL_PRODUCT_EM12			0x0512
>  #define QUECTEL_PRODUCT_RM500Q			0x0800
>  #define QUECTEL_PRODUCT_EC200S_CN		0x6002
> @@ -1134,6 +1135,8 @@ static const struct usb_device_id option_ids[] = {
>  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0xff, 0xff),
>  	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
>  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
> +	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
> +	  .driver_info = RSVD(6) | ZLP }, 

Checkpatch now also warn of trailing whitespace here. Please remember to
run scripts/checkpatch.pl before submitting.

>  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0xff, 0xff),
>  	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
>  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0, 0) },

Johan