Re: [PATCH v2 2/2] phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support

[Robert Marko]

On Tue, 21 Jun 2022 at 19:26, Dmitry Baryshkov
<dmitry.baryshkov@xxxxxxxxxx> wrote:
>
> On Tue, 21 Jun 2022 at 14:18, Robert Marko <robimarko@xxxxxxxxx> wrote:
> >
> > IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3.
> > Gen2 one is already supported, so add the support for the Gen3 one.
> > It uses the same register layout as IPQ6018.
> >
> > Signed-off-by: Robert Marko <robimarko@xxxxxxxxx>
> > ---
> > Changes in v2:
> > * Rebase onto next-20220621 to apply on the refactored driver
> > * Remove non existant has_phy_com_ctrl and has_lane_rst
> > ---
> >  drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 171 ++++++++++++++++++++++-
> >  1 file changed, 169 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > index b2cd0cf965d8..b4836417b2c0 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>
> [skipped]
>
> > @@ -2121,8 +2277,16 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
> >
> >         init.ops = &clk_fixed_rate_ops;
> >
> > -       /* controllers using QMP phys use 125MHz pipe clock interface */
> > -       fixed->fixed_rate = 125000000;
> > +       /*
> > +        * Controllers using QMP PHY-s use 125MHz pipe clock interface
> > +        * unless other frequency is specified in the DTS.
> > +        */
> > +       ret = of_property_read_u32(np, "clock-output-rate", &rate);
>
> The clock-output-rate is a new property, which doesn't exist yet. If
> the rate is peculiar to your platform/PHY, I'd suggest adding a field
> to the qmp configuration instead.

Hi,
That sounds like a better idea than adding new DT property, it's
specific only to the Gen3 PHY
for IPQ8074.

I will change it for v3.

Regards,
Robert
>
> > +       if (ret)
> > +               fixed->fixed_rate = 125000000;
> > +       else
> > +               fixed->fixed_rate = rate;
> > +
> >         fixed->hw.init = &init;
> >
> >         ret = devm_clk_hw_register(qmp->dev, &fixed->hw);
> > @@ -2255,6 +2419,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = {
> >         }, {
> >                 .compatible = "qcom,ipq8074-qmp-pcie-phy",
> >                 .data = &ipq8074_pciephy_cfg,
> > +       }, {
> > +               .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy",
> > +               .data = &ipq8074_pciephy_gen3_cfg,
> >         }, {
> >                 .compatible = "qcom,ipq6018-qmp-pcie-phy",
> >                 .data = &ipq6018_pciephy_cfg,
> > --
> > 2.36.1
> >
>
>
> --
> With best wishes
> Dmitry