Re: [PATCH v2] Bluetooth: Fix CVSD SCO setup failure

[quic_zijuhu]

On 6/9/2022 7:09 PM, Zijun Hu wrote:
> It will set up SCO after all CVSD eSCO attempts failure, but
> still fails to set up SCO finally due to wrong D1/D0 @retrans_effort
> within @esco_param_cvsd, so change it from 0x1 to 0xff to avoid
> Invalid HCI Command Parameters error.
> 
> < HCI Command: Setup Synchrono.. (0x01|0x0028) plen 17  #3427
>         Handle: 3
>         Transmit bandwidth: 8000
>         Receive bandwidth: 8000
>         Max latency: 65535
>         Setting: 0x0060
>           Input Coding: Linear
>           Input Data Format: 2's complement
>           Input Sample Size: 16-bit
>           # of bits padding at MSB: 0
>           Air Coding Format: CVSD
>         Retransmission effort: Optimize for power consumption (0x01)
>         Packet type: 0x03c4
>           HV3 may be used
>           2-EV3 may not be used
>           3-EV3 may not be used
>           2-EV5 may not be used
>           3-EV5 may not be used
>> HCI Event: Command Status (0x0f) plen 4               #3428
>       Setup Synchronous Connection (0x01|0x0028) ncmd 1
>         Status: Success (0x00)
>> HCI Event: Synchronous Connect Comp.. (0x2c) plen 17  #3429
>         Status: Invalid HCI Command Parameters (0x12)
>         Handle: 0
>         Address: 14:3F:A6:47:56:15 (OUI 14-3F-A6)
>         Link type: SCO (0x00)
>         Transmission interval: 0x00
>         Retransmission window: 0x00
>         RX packet length: 0
>         TX packet length: 0
>         Air mode: u-law log (0x00)
> 
> Signed-off-by: Zijun Hu <quic_zijuhu@xxxxxxxxxxx>
> ---
>  net/bluetooth/hci_conn.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
> index 7829433d54c1..2627d5ac15d6 100644
> --- a/net/bluetooth/hci_conn.c
> +++ b/net/bluetooth/hci_conn.c
> @@ -45,8 +45,8 @@ static const struct sco_param esco_param_cvsd[] = {
>  	{ EDR_ESCO_MASK & ~ESCO_2EV3, 0x000a,	0x01 }, /* S3 */
>  	{ EDR_ESCO_MASK & ~ESCO_2EV3, 0x0007,	0x01 }, /* S2 */
>  	{ EDR_ESCO_MASK | ESCO_EV3,   0x0007,	0x01 }, /* S1 */
> -	{ EDR_ESCO_MASK | ESCO_HV3,   0xffff,	0x01 }, /* D1 */
> -	{ EDR_ESCO_MASK | ESCO_HV1,   0xffff,	0x01 }, /* D0 */
> +	{ EDR_ESCO_MASK | ESCO_HV3,   0xffff,	0xff }, /* D1 */
> +	{ EDR_ESCO_MASK | ESCO_HV1,   0xffff,	0xff }, /* D0 */
>  };
>  
>  static const struct sco_param sco_param_cvsd[] = {
could you code review for this change?