Re: [PATCH 7/7] media: dt-bindings: ov5693: document YAML binding

[Krzysztof Kozlowski]

On 25/06/2022 01:03, Tommaso Merciai wrote:
> This patch adds documentation of device tree in YAML schema for the
> OV5693 CMOS image sensor from Omnivision
> 
> Signed-off-by: Tommaso Merciai <tommaso.merciai@xxxxxxxxxxxxxxxxxxxx>
> ---
>  .../bindings/media/i2c/ovti,ov5693.yaml       | 123 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 124 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> new file mode 100644
> index 000000000000..1ee70af40000
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
> @@ -0,0 +1,123 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (c) 2022 Amarulasolutions
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Omnivision OV5693 CMOS Sensor
> +
> +maintainers:
> +  - Tommaso Merciai <tommaso.merciai@xxxxxxxxxxxxxxxxxxxx>
> +
> +allOf:
> +  - $ref: /schemas/media/video-interface-devices.yaml#

This goes after description.

> +
> +description: |
> +  The Omnivision OV5693 is a high performance, 1/4-inch, 5 megapixel, CMOS
> +  image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
> +  sub-sampled, and windowed 10-bit MIPI images in various formats via the
> +  Serial Camera Control Bus (SCCB) interface.
> +
> +  Supports images sizes: 5 Mpixel, EIS1080p, 1080p, 720p, VGA, QVGA
> +
> +  OV5693 is programmable through I2C and two-wire Serial Camera Control Bus (SCCB).
> +  The sensor output is available via CSI-2 serial data output (up to 2-lane).
> +
> +properties:
> +  compatible:
> +    const: ovti,ov5693
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    description:
> +      System input clock (aka XVCLK). From 6 to 27 MHz.
> +    maxItems: 1
> +
> +  dovdd-supply:
> +    description:
> +      Digital I/O voltage supply, 1.8V.
> +
> +  avdd-supply:
> +    description:
> +      Analog voltage supply, 2.8V.
> +
> +  dvdd-supply:
> +    description:
> +      Digital core voltage supply, 1.2V.
> +
> +  reset-gpios:
> +    description:
> +      The phandle and specifier for the GPIO that controls sensor reset.
> +      This corresponds to the hardware pin XSHUTDN which is physically
> +      active low.
> +    maxItems: 1
> +
> +  port:
> +    $ref: /schemas/graph.yaml#/$defs/port-base
> +    additionalProperties: false
> +
> +    properties:
> +      endpoint:
> +        $ref: /schemas/media/video-interfaces.yaml#
> +        unevaluatedProperties: false
> +
> +        properties:
> +          data-lanes:
> +            minItems: 1
> +            maxItems: 2
> +
> +          # Supports max data transfer of 900 Mbps per lane
> +          link-frequencies: true

This is not needed. Provided by video-interfaces.yaml.

> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - dovdd-supply
> +  - avdd-supply
> +  - dvdd-supply
> +  - port
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/px30-cru.h>
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/pinctrl/rockchip.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        ov5693: camera@36 {
> +            compatible = "ovti,ov5693";
> +            reg = <0x36>;
> +
> +            reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
> +            pinctrl-names = "default";
> +            pinctrl-0 = <&cif_clkout_m0>;
> +
> +            clocks = <&cru SCLK_CIF_OUT>;
> +            assigned-clocks = <&cru SCLK_CIF_OUT>;
> +            assigned-clock-rates = <19200000>;
> +
> +            avdd-supply = <&vcc_1v8>;
> +            dvdd-supply = <&vcc_1v2>;
> +            dovdd-supply = <&vcc_2v8>;
> +
> +            rotation = <90>;
> +            orientation = <0>;
> +
> +            port {
> +                ucam_out: endpoint {
> +                    remote-endpoint = <&mipi_in_ucam>;
> +                    data-lanes = <1 2>;
> +                    link-frequencies = /bits/ 64 <450000000>;
> +                };
> +            };
> +        };
> +    };
> \ No newline at end of file

^^^ This has to be fixed.

> diff --git a/MAINTAINERS b/MAINTAINERS
Best regards,
Krzysztof