[PATCH v1 4/9] dt-bindings: mips: lantiq: rcu: Remove binding documentation

[Martin Blumenstingl]

This is now part of:
Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml

The PHYs are still using sub-nodes while the reset-controller is moved
to the main RCU node. Also the system reboot is now described directly
in intel,rcu-gw.yaml which makes the syscon-reboot node obsolete.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
---
 .../devicetree/bindings/mips/lantiq/rcu.txt   | 69 -------------------
 1 file changed, 69 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mips/lantiq/rcu.txt

diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt
deleted file mode 100644
index 58d51f480c9e..000000000000
--- a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt
+++ /dev/null
@@ -1,69 +0,0 @@
-Lantiq XWAY SoC RCU binding
-===========================
-
-This binding describes the RCU (reset controller unit) multifunction device,
-where each sub-device has it's own set of registers.
-
-The RCU register range is used for multiple purposes. Mostly one device
-uses one or multiple register exclusively, but for some registers some
-bits are for one driver and some other bits are for a different driver.
-With this patch all accesses to the RCU registers will go through
-syscon.
-
-
--------------------------------------------------------------------------------
-Required properties:
-- compatible	: The first and second values must be:
-		  "lantiq,xrx200-rcu", "simple-mfd", "syscon"
-- reg		: The address and length of the system control registers
-
-
--------------------------------------------------------------------------------
-Example of the RCU bindings on a xRX200 SoC:
-	rcu0: rcu@203000 {
-		compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon";
-		reg = <0x203000 0x100>;
-		ranges = <0x0 0x203000 0x100>;
-		big-endian;
-
-		reset0: reset-controller@10 {
-			compatible = "lantiq,xrx200-reset";
-			reg = <0x10 4>, <0x14 4>;
-
-			#reset-cells = <2>;
-		};
-
-		reset1: reset-controller@48 {
-			compatible = "lantiq,xrx200-reset";
-			reg = <0x48 4>, <0x24 4>;
-
-			#reset-cells = <2>;
-		};
-
-		usb_phy0: usb2-phy@18 {
-			compatible = "lantiq,xrx200-usb2-phy";
-			reg = <0x18 4>, <0x38 4>;
-
-			resets = <&reset1 4 4>, <&reset0 4 4>;
-			reset-names = "phy", "ctrl";
-			#phy-cells = <0>;
-		};
-
-		usb_phy1: usb2-phy@34 {
-			compatible = "lantiq,xrx200-usb2-phy";
-			reg = <0x34 4>, <0x3C 4>;
-
-			resets = <&reset1 5 4>, <&reset0 4 4>;
-			reset-names = "phy", "ctrl";
-			#phy-cells = <0>;
-		};
-
-		reboot@10 {
-			compatible = "syscon-reboot";
-			reg = <0x10 4>;
-
-			regmap = <&rcu0>;
-			offset = <0x10>;
-			mask = <0x40000000>;
-		};
-	};
-- 
2.36.1