Re: [RESEND PATCH v4 3/6] Input: edt-ft5x06 - set report rate by dts property

[Dmitry Torokhov]

Hi Dario,

On Tue, Jun 21, 2022 at 02:39:34PM +0200, Dario Binacchi wrote:
> It allows to change the M06/M12 default scan rate on driver probing.
> 
> Co-developed-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Dario Binacchi <dario.binacchi@xxxxxxxxxxxxxxxxxxxx>
> 
> ---
> 
> (no changes since v3)
> 
> Changes in v3:
> - Check the lower and upper limits of the report-rate-hz value
> - Convert the M06 report-rate-hz value
> 
>  drivers/input/touchscreen/edt-ft5x06.c | 30 ++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 77f061af5c61..843e8b0522f7 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -1084,6 +1084,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  	struct input_dev *input;
>  	unsigned long irq_flags;
>  	int error;
> +	u32 report_rate;
>  	char fw_version[EDT_NAME_LEN];
>  
>  	dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
> @@ -1213,6 +1214,35 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  	edt_ft5x06_ts_get_defaults(&client->dev, tsdata);
>  	edt_ft5x06_ts_get_parameters(tsdata);
>  
> +	if (tsdata->reg_addr.reg_report_rate != NO_REGISTER &&
> +	    !of_property_read_u32(client->dev.of_node, "report-rate-hz",

Unless there is a strong reason to use of-specific version of properties
API, generic device property API is preferred. I changed this to
device_property_read_u32().


> +				  &report_rate)) {
> +		tsdata->report_rate = report_rate;
> +		if (tsdata->version == EDT_M06) {
> +			if (report_rate < 30)
> +				report_rate = 30;
> +			else if (report_rate > 140)
> +				report_rate = 140;

We have a nice macro clamp_val() for this.

> +		} else if (report_rate < 1) {
> +			report_rate = 1;
> +		} else if (report_rate > 255)
> +			report_rate = 255;

Same here. I made the change and applied.

> +
> +		if (report_rate != tsdata->report_rate)
> +			dev_warn(&client->dev,
> +				 "report-rate %dHz is unsupported, use %dHz\n",
> +				 tsdata->report_rate, report_rate);
> +
> +		if (tsdata->version == EDT_M06)
> +			report_rate /= 10;
> +
> +		tsdata->report_rate = report_rate;
> +
> +		edt_ft5x06_register_write(tsdata,
> +					  tsdata->reg_addr.reg_report_rate,
> +					  tsdata->report_rate);
> +	}
> +
>  	dev_dbg(&client->dev,
>  		"Model \"%s\", Rev. \"%s\", %dx%d sensors\n",
>  		tsdata->name, fw_version, tsdata->num_x, tsdata->num_y);
> -- 
> 2.32.0
> 

Thanks.

-- 
Dmitry