Re: [PATCH v5 11/13] leds: mt6370: Add MediaTek MT6370 current sink type LED Indicator support

[ChiYuan Huang]

ChiYuan Huang <u0084500@xxxxxxxxx> 於 2022年7月20日 週三 下午5:48寫道：
>
> ChiYuan Huang <u0084500@xxxxxxxxx> 於 2022年7月20日 週三 下午5:45寫道：
> >
> > On Fri, Jul 15, 2022 at 08:29:42PM +0200, Andy Shevchenko wrote:
> > > On Fri, Jul 15, 2022 at 1:29 PM ChiaEn Wu <peterwu.pub@xxxxxxxxx> wrote:
> > > >
> > > > From: ChiYuan Huang <cy_huang@xxxxxxxxxxx>
> > > >
> > > > The MediaTek MT6370 is a highly-integrated smart power management IC,
> > > > which includes a single cell Li-Ion/Li-Polymer switching battery
> > > > charger, a USB Type-C & Power Delivery (PD) controller, dual
> > > > Flash LED current sources, a RGB LED driver, a backlight WLED driver,
> > > > a display bias driver and a general LDO for portable devices.
> > > >
> > > > In MediaTek MT6370, there are four channel current-sink RGB LEDs that
> > > > support hardware pattern for constant current, PWM, and breath mode.
> > > > Isink4 channel can also be used as a CHG_VIN power good indicator.
> > >
> > > ...
> > >
> > > > +         This driver can also be built as a module. If so the module
> > >
> > > so, the
> > >
> > > > +         will be called "leds-mt6370.ko".
> > >
> > > No ".ko".
> > >
> > > Why did you ignore these comments? Please go and fix _everywhere_ in
> > > your series.
> > > It's basically the rule of thumb, if the reviewer gives a comment
> > > against an occurrence of something, go through entire series and check
> > > if there are other places like commented one and address them all.
> > >
> > > ...
> > >
> > > > + * Author: Alice Chen <alice_chen@xxxxxxxxxxx>
> > >
> > > Strange, the commit message doesn't have a corresponding SoB, why?
> > >
> > Yes, there're two authors Alice and me.
> > I'll correct it in next.
> > > ...
> > >
> > > > +#define MT6370_PWM_DUTY                                31
> > > > +#define MT6372_PMW_DUTY                                255
> > >
> > > Looks like these are limits by hardware?
> > > Check with the datasheet if (BIT(x) - 1) makes more sense here.
> > >
> > > ...
> > >
> > > > +       switch (led_no) {
> > > > +       case MT6370_LED_ISNK1:
> > > > +               sel_field = F_LED1_DUTY;
> > > > +               break;
> > > > +       case MT6370_LED_ISNK2:
> > > > +               sel_field = F_LED2_DUTY;
> > > > +               break;
> > > > +       case MT6370_LED_ISNK3:
> > > > +               sel_field = F_LED3_DUTY;
> > > > +               break;
> > > > +       default:
> > > > +               sel_field = F_LED4_DUTY;
> > >
> > > Missed break;
> > >
> > > > +       }
> > >
> > > ...
> > >
> > > > +       switch (led_no) {
> > > > +       case MT6370_LED_ISNK1:
> > > > +               sel_field = F_LED1_FREQ;
> > > > +               break;
> > > > +       case MT6370_LED_ISNK2:
> > > > +               sel_field = F_LED2_FREQ;
> > > > +               break;
> > > > +       case MT6370_LED_ISNK3:
> > > > +               sel_field = F_LED3_FREQ;
> > > > +               break;
> > > > +       default:
> > > > +               sel_field = F_LED4_FREQ;
> > >
> > > Ditto.
> > >
> > > > +       }
> > >
> > > ...
> > >
> > > > +       switch (led_no) {
> > > > +       case MT6370_LED_ISNK1:
> > > > +       case MT6370_LED_ISNK2:
> > > > +       case MT6370_LED_ISNK3:
> > > > +               *base = MT6370_REG_RGB1_TR + led_no * 3;
> > > > +               break;
> > > > +       default:
> > > > +               *base = MT6370_REG_RGB_CHRIND_TR;
> > >
> > > Ditto.
> > > It seems you dropped them for all switch-cases. It's not goot, please
> > > restore them back.
> > >
> > > > +       }
> > >
> > > ...
> > >
> > > > +       u8 val[P_MAX_PATTERNS / 2] = {0};
> > >
> > > { } should suffice
> > >
> > >
> > In the above range selector, we use the 'logic or' to generate the
> typo, it's 'below'.
> > pattern values.
> >
Ah, found in c11 standard 6.7.9 item 21
It is the same as 'static storage duration'.
I will follow your comment to revise it.
Thanks.
> > If to change it from '{0} to '{ }', is it correct?
> > > > +       /*
> > > > +        * Pattern list
> > > > +        * tr1: byte 0, b'[7: 4]
> > > > +        * tr2: byte 0, b'[3: 0]
> > > > +        * tf1: byte 1, b'[7: 4]
> > > > +        * tf2: byte 1, b'[3: 0]
> > > > +        * ton: byte 2, b'[7: 4]
> > > > +        * toff: byte 2, b'[3: 0]
> > > > +        */
> > > > +       for (i = 0; i < P_MAX_PATTERNS; i++) {
> > > > +               curr = pattern + i;
> > > > +
> > > > +               sel_range = i == P_LED_TOFF ? R_LED_TOFF : R_LED_TRFON;
> > > > +
> > > > +               linear_range_get_selector_within(priv->ranges + sel_range,
> > > > +                                                curr->delta_t, &sel);
> > > > +
> > > > +               val[i / 2] |= sel << (4 * ((i + 1) % 2));
> > > > +       }
> > > > +
> > > > +       memcpy(pattern_val, val, 3);
> > > > +       return 0;
> > > > +}
> > >
> > > ...
> > >
> > > > +out:
> > >
> > > out_unlock:
> > >
> > > > +       mutex_unlock(&priv->lock);
> > > > +
> > > > +       return ret;
> > >
> > > ...
> > >
> > > > +out:
> > >
> > > Ditto. And so on.
> > >
> > > > +       mutex_unlock(&priv->lock);
> > > > +
> > > > +       return ret;
> > >
> > > ...
> > >
> > > > +               sub_led = devm_kzalloc(priv->dev,
> > > > +                                      sizeof(*sub_led) * MC_CHANNEL_NUM,
> > > > +                                      GFP_KERNEL);
> > >
> > > NIH devm_kcalloc(). Also check if you really need zeroed data.
> > >
> > Ok, and after the check, I also need to add one line to set the intensity to 0.
> > > > +               if (!sub_led)
> > > > +                       return -ENOMEM;
> > >
> > > ...
> > >
> > > > +                       ret = fwnode_property_read_u32(child, "color", &color);
> > > > +                       if (ret) {
> > > > +                               dev_err(priv->dev,
> > > > +                                       "led %d, no color specified\n",
> > > > +                                       led->index);
> > > > +                               return ret;
> > >
> > > return dev_err_probe(...) ; ?
> > >
> > > Ditto for many places in your entire series.
> > >
> > > > +                       }
> > >
> > > ...
> > >
> > > > +       priv = devm_kzalloc(&pdev->dev,
> > > > +                           struct_size(priv, leds, count), GFP_KERNEL);
> > >
> > > At least one parameter can be placed on the previous line.
> > >
> > > > +       if (!priv)
> > > > +               return -ENOMEM;
> > >
> > > --
> > > With Best Regards,
> > > Andy Shevchenko