Re: [PATCH 1/2] ARM: dts: qcom: ipq8064: reorganize node order and sort them
From: Christian Marangi
Date: Mon Aug 08 2022 - 16:04:20 EST
On Mon, Jul 18, 2022 at 05:38:14PM +0200, Christian Marangi wrote:
> Reorganize node order and sort them by address.
>
So how to proceed with this? Should I send v2 with the changes pointed
(stuff with no reg outside soc) or it's a NACK for the unnecessary
changes?
I feel a bit stuck.
> Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> ---
>
> This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
>
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
>
> arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++--------------
> 1 file changed, 383 insertions(+), 383 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> index da90f7c08d75..cf41d330c920 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> @@ -332,19 +332,59 @@ soc: soc {
> ranges;
> compatible = "simple-bus";
>
> - lpass@28100000 {
> - compatible = "qcom,lpass-cpu";
> - status = "disabled";
> - clocks = <&lcc AHBIX_CLK>,
> - <&lcc MI2S_OSR_CLK>,
> - <&lcc MI2S_BIT_CLK>;
> - clock-names = "ahbix-clk",
> - "mi2s-osr-clk",
> - "mi2s-bit-clk";
> - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
> - interrupt-names = "lpass-irq-lpaif";
> - reg = <0x28100000 0x10000>;
> - reg-names = "lpass-lpaif";
> + stmmac_axi_setup: stmmac-axi-config {
> + snps,wr_osr_lmt = <7>;
> + snps,rd_osr_lmt = <7>;
> + snps,blen = <16 0 0 0 0 0 0>;
> + };
> +
> + vsdcc_fixed: vsdcc-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "SDCC Power";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + rpm: rpm@108000 {
> + compatible = "qcom,rpm-ipq8064";
> + reg = <0x108000 0x1000>;
> + qcom,ipc = <&l2cc 0x8 2>;
> +
> + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "ack", "err", "wakeup";
> +
> + clocks = <&gcc RPM_MSG_RAM_H_CLK>;
> + clock-names = "ram";
> +
> + rpmcc: clock-controller {
> + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
> + #clock-cells = <1>;
> + };
> + };
> +
> + qcom,ssbi@500000 {
> + compatible = "qcom,ssbi";
> + reg = <0x00500000 0x1000>;
> + qcom,controller-type = "pmic-arbiter";
> + };
> +
> + qfprom: qfprom@700000 {
> + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
> + reg = <0x00700000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + speedbin_efuse: speedbin@c0 {
> + reg = <0xc0 0x4>;
> + };
> + tsens_calib: calib@400 {
> + reg = <0x400 0xb>;
> + };
> + tsens_calib_backup: calib_backup@410 {
> + reg = <0x410 0xb>;
> + };
> };
>
> qcom_pinmux: pinmux@800000 {
> @@ -471,6 +511,35 @@ mux {
> };
> };
>
> + gcc: clock-controller@900000 {
> + compatible = "qcom,gcc-ipq8064", "syscon";
> + clocks = <&pxo_board>, <&cxo_board>;
> + clock-names = "pxo", "cxo";
> + reg = <0x00900000 0x4000>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> +
> + tsens: thermal-sensor@900000 {
> + compatible = "qcom,ipq8064-tsens";
> +
> + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
> + nvmem-cell-names = "calib", "calib_backup";
> + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow";
> +
> + #qcom,sensors = <11>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + sfpb_mutex: hwlock@1200600 {
> + compatible = "qcom,sfpb-mutex";
> + reg = <0x01200600 0x100>;
> +
> + #hwlock-cells = <1>;
> + };
> +
> intc: interrupt-controller@2000000 {
> compatible = "qcom,msm-qgic2";
> interrupt-controller;
> @@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>,
> cpu-offset = <0x80000>;
> };
>
> + l2cc: clock-controller@2011000 {
> + compatible = "qcom,kpss-gcc", "syscon";
> + reg = <0x2011000 0x1000>;
> + clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
> + clock-names = "pll8_vote", "pxo";
> + clock-output-names = "acpu_l2_aux";
> + };
> +
> acc0: clock-controller@2088000 {
> compatible = "qcom,kpss-acc-v1";
> reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
> };
>
> + saw0: regulator@2089000 {
> + compatible = "qcom,saw2";
> + reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
> + regulator;
> + };
> +
> acc1: clock-controller@2098000 {
> compatible = "qcom,kpss-acc-v1";
> reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
> };
>
> - adm_dma: dma-controller@18300000 {
> - compatible = "qcom,adm";
> - reg = <0x18300000 0x100000>;
> - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> - #dma-cells = <1>;
> + saw1: regulator@2099000 {
> + compatible = "qcom,saw2";
> + reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
> + regulator;
> + };
>
> - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
> - clock-names = "core", "iface";
> + nss_common: syscon@03000000 {
> + compatible = "syscon";
> + reg = <0x03000000 0x0000FFFF>;
> + };
>
> - resets = <&gcc ADM0_RESET>,
> - <&gcc ADM0_PBUS_RESET>,
> - <&gcc ADM0_C0_RESET>,
> - <&gcc ADM0_C1_RESET>,
> - <&gcc ADM0_C2_RESET>;
> - reset-names = "clk", "pbus", "c0", "c1", "c2";
> - qcom,ee = <0>;
> + usb3_0: usb3@100f8800 {
> + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x100f8800 0x8000>;
> + clocks = <&gcc USB30_0_MASTER_CLK>;
> + clock-names = "core";
> +
> + ranges;
> +
> + resets = <&gcc USB30_0_MASTER_RESET>;
> + reset-names = "master";
>
> status = "disabled";
> +
> + dwc3_0: dwc3@10000000 {
> + compatible = "snps,dwc3";
> + reg = <0x10000000 0xcd00>;
> + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&hs_phy_0>, <&ss_phy_0>;
> + phy-names = "usb2-phy", "usb3-phy";
> + dr_mode = "host";
> + snps,dis_u3_susphy_quirk;
> + };
> };
>
> - saw0: regulator@2089000 {
> - compatible = "qcom,saw2";
> - reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
> - regulator;
> + hs_phy_0: phy@100f8800 {
> + compatible = "qcom,ipq806x-usb-phy-hs";
> + reg = <0x100f8800 0x30>;
> + clocks = <&gcc USB30_0_UTMI_CLK>;
> + clock-names = "ref";
> + #phy-cells = <0>;
> +
> + status = "disabled";
> };
>
> - saw1: regulator@2099000 {
> - compatible = "qcom,saw2";
> - reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
> - regulator;
> + ss_phy_0: phy@100f8830 {
> + compatible = "qcom,ipq806x-usb-phy-ss";
> + reg = <0x100f8830 0x30>;
> + clocks = <&gcc USB30_0_MASTER_CLK>;
> + clock-names = "ref";
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + usb3_1: usb3@110f8800 {
> + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x110f8800 0x8000>;
> + clocks = <&gcc USB30_1_MASTER_CLK>;
> + clock-names = "core";
> +
> + ranges;
> +
> + resets = <&gcc USB30_1_MASTER_RESET>;
> + reset-names = "master";
> +
> + status = "disabled";
> +
> + dwc3_1: dwc3@11000000 {
> + compatible = "snps,dwc3";
> + reg = <0x11000000 0xcd00>;
> + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&hs_phy_1>, <&ss_phy_1>;
> + phy-names = "usb2-phy", "usb3-phy";
> + dr_mode = "host";
> + snps,dis_u3_susphy_quirk;
> + };
> + };
> +
> + hs_phy_1: phy@110f8800 {
> + compatible = "qcom,ipq806x-usb-phy-hs";
> + reg = <0x110f8800 0x30>;
> + clocks = <&gcc USB30_1_UTMI_CLK>;
> + clock-names = "ref";
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + ss_phy_1: phy@110f8830 {
> + compatible = "qcom,ipq806x-usb-phy-ss";
> + reg = <0x110f8830 0x30>;
> + clocks = <&gcc USB30_1_MASTER_CLK>;
> + clock-names = "ref";
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + sdcc3bam: dma-controller@12182000 {
> + compatible = "qcom,bam-v1.3.0";
> + reg = <0x12182000 0x8000>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc SDC3_H_CLK>;
> + clock-names = "bam_clk";
> + #dma-cells = <1>;
> + qcom,ee = <0>;
> + };
> +
> + sdcc1bam: dma-controller@12402000 {
> + compatible = "qcom,bam-v1.3.0";
> + reg = <0x12402000 0x8000>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc SDC1_H_CLK>;
> + clock-names = "bam_clk";
> + #dma-cells = <1>;
> + qcom,ee = <0>;
> + };
> +
> + amba: amba {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + sdcc3: mmc@12180000 {
> + compatible = "arm,pl18x", "arm,primecell";
> + arm,primecell-periphid = <0x00051180>;
> + status = "disabled";
> + reg = <0x12180000 0x2000>;
> + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "cmd_irq";
> + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
> + clock-names = "mclk", "apb_pclk";
> + bus-width = <8>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + max-frequency = <192000000>;
> + sd-uhs-sdr104;
> + sd-uhs-ddr50;
> + vqmmc-supply = <&vsdcc_fixed>;
> + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
> + dma-names = "tx", "rx";
> + };
> +
> + sdcc1: mmc@12400000 {
> + status = "disabled";
> + compatible = "arm,pl18x", "arm,primecell";
> + arm,primecell-periphid = <0x00051180>;
> + reg = <0x12400000 0x2000>;
> + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "cmd_irq";
> + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
> + clock-names = "mclk", "apb_pclk";
> + bus-width = <8>;
> + max-frequency = <96000000>;
> + non-removable;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + vmmc-supply = <&vsdcc_fixed>;
> + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
> + dma-names = "tx", "rx";
> + };
> };
>
> gsbi1: gsbi@12440000 {
> @@ -654,56 +875,6 @@ i2c@16380000 {
> };
> };
>
> - gsbi5: gsbi@1a200000 {
> - compatible = "qcom,gsbi-v1.0.0";
> - cell-index = <5>;
> - reg = <0x1a200000 0x100>;
> - clocks = <&gcc GSBI5_H_CLK>;
> - clock-names = "iface";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> - status = "disabled";
> -
> - syscon-tcsr = <&tcsr>;
> -
> - gsbi5_serial: serial@1a240000 {
> - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
> - reg = <0x1a240000 0x1000>,
> - <0x1a200000 0x1000>;
> - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
> - clock-names = "core", "iface";
> - status = "disabled";
> - };
> -
> - i2c@1a280000 {
> - compatible = "qcom,i2c-qup-v1.1.1";
> - reg = <0x1a280000 0x1000>;
> - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> -
> - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> - clock-names = "core", "iface";
> - status = "disabled";
> -
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi@1a280000 {
> - compatible = "qcom,spi-qup-v1.1.1";
> - reg = <0x1a280000 0x1000>;
> - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> -
> - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> - clock-names = "core", "iface";
> - status = "disabled";
> -
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> - };
> -
> gsbi6: gsbi@16500000 {
> compatible = "qcom,gsbi-v1.0.0";
> reg = <0x16500000 0x100>;
> @@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 {
> };
> };
>
> - rng@1a500000 {
> - compatible = "qcom,prng";
> - reg = <0x1a500000 0x200>;
> - clocks = <&gcc PRNG_CLK>;
> - clock-names = "core";
> - };
> + adm_dma: dma-controller@18300000 {
> + compatible = "qcom,adm";
> + reg = <0x18300000 0x100000>;
> + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> + #dma-cells = <1>;
>
> - sata_phy: sata-phy@1b400000 {
> - compatible = "qcom,ipq806x-sata-phy";
> - reg = <0x1b400000 0x200>;
> + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
> + clock-names = "core", "iface";
>
> - clocks = <&gcc SATA_PHY_CFG_CLK>;
> - clock-names = "cfg";
> + resets = <&gcc ADM0_RESET>,
> + <&gcc ADM0_PBUS_RESET>,
> + <&gcc ADM0_C0_RESET>,
> + <&gcc ADM0_C1_RESET>,
> + <&gcc ADM0_C2_RESET>;
> + reset-names = "clk", "pbus", "c0", "c1", "c2";
> + qcom,ee = <0>;
>
> - #phy-cells = <0>;
> status = "disabled";
> };
>
> - nand: nand-controller@1ac00000 {
> - compatible = "qcom,ipq806x-nand";
> - reg = <0x1ac00000 0x800>;
> -
> - pinctrl-0 = <&nand_pins>;
> - pinctrl-names = "default";
> -
> - clocks = <&gcc EBI2_CLK>,
> - <&gcc EBI2_AON_CLK>;
> - clock-names = "core", "aon";
> -
> - dmas = <&adm_dma 3>;
> - dma-names = "rxtx";
> - qcom,cmd-crci = <15>;
> - qcom,data-crci = <3>;
> -
> + gsbi5: gsbi@1a200000 {
> + compatible = "qcom,gsbi-v1.0.0";
> + cell-index = <5>;
> + reg = <0x1a200000 0x100>;
> + clocks = <&gcc GSBI5_H_CLK>;
> + clock-names = "iface";
> #address-cells = <1>;
> - #size-cells = <0>;
> -
> + #size-cells = <1>;
> + ranges;
> status = "disabled";
> - };
>
> - sata: sata@29000000 {
> - compatible = "qcom,ipq806x-ahci", "generic-ahci";
> - reg = <0x29000000 0x180>;
> + syscon-tcsr = <&tcsr>;
>
> - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> + gsbi5_serial: serial@1a240000 {
> + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
> + reg = <0x1a240000 0x1000>,
> + <0x1a200000 0x1000>;
> + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
> + };
>
> - clocks = <&gcc SFAB_SATA_S_H_CLK>,
> - <&gcc SATA_H_CLK>,
> - <&gcc SATA_A_CLK>,
> - <&gcc SATA_RXOOB_CLK>,
> - <&gcc SATA_PMALIVE_CLK>;
> - clock-names = "slave_face", "iface", "core",
> - "rxoob", "pmalive";
> + i2c@1a280000 {
> + compatible = "qcom,i2c-qup-v1.1.1";
> + reg = <0x1a280000 0x1000>;
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>
> - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
> - assigned-clock-rates = <100000000>, <100000000>;
> + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
>
> - phys = <&sata_phy>;
> - phy-names = "sata-phy";
> - status = "disabled";
> - };
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
>
> - qcom,ssbi@500000 {
> - compatible = "qcom,ssbi";
> - reg = <0x00500000 0x1000>;
> - qcom,controller-type = "pmic-arbiter";
> - };
> + spi@1a280000 {
> + compatible = "qcom,spi-qup-v1.1.1";
> + reg = <0x1a280000 0x1000>;
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>
> - qfprom: qfprom@700000 {
> - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
> - reg = <0x00700000 0x1000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - speedbin_efuse: speedbin@c0 {
> - reg = <0xc0 0x4>;
> - };
> - tsens_calib: calib@400 {
> - reg = <0x400 0xb>;
> - };
> - tsens_calib_backup: calib_backup@410 {
> - reg = <0x410 0xb>;
> + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> };
> };
>
> - gcc: clock-controller@900000 {
> - compatible = "qcom,gcc-ipq8064", "syscon";
> - clocks = <&pxo_board>, <&cxo_board>;
> - clock-names = "pxo", "cxo";
> - reg = <0x00900000 0x4000>;
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - #power-domain-cells = <1>;
> -
> - tsens: thermal-sensor@900000 {
> - compatible = "qcom,ipq8064-tsens";
> -
> - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
> - nvmem-cell-names = "calib", "calib_backup";
> - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "uplow";
> + tcsr: syscon@1a400000 {
> + compatible = "qcom,tcsr-ipq8064", "syscon";
> + reg = <0x1a400000 0x100>;
> + };
>
> - #qcom,sensors = <11>;
> - #thermal-sensor-cells = <1>;
> - };
> + rng@1a500000 {
> + compatible = "qcom,prng";
> + reg = <0x1a500000 0x200>;
> + clocks = <&gcc PRNG_CLK>;
> + clock-names = "core";
> };
>
> - rpm: rpm@108000 {
> - compatible = "qcom,rpm-ipq8064";
> - reg = <0x108000 0x1000>;
> - qcom,ipc = <&l2cc 0x8 2>;
> + nand: nand-controller@1ac00000 {
> + compatible = "qcom,ipq806x-nand";
> + reg = <0x1ac00000 0x800>;
>
> - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "ack", "err", "wakeup";
> + pinctrl-0 = <&nand_pins>;
> + pinctrl-names = "default";
>
> - clocks = <&gcc RPM_MSG_RAM_H_CLK>;
> - clock-names = "ram";
> + clocks = <&gcc EBI2_CLK>,
> + <&gcc EBI2_AON_CLK>;
> + clock-names = "core", "aon";
> +
> + dmas = <&adm_dma 3>;
> + dma-names = "rxtx";
> + qcom,cmd-crci = <15>;
> + qcom,data-crci = <3>;
>
> - rpmcc: clock-controller {
> - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
> - #clock-cells = <1>;
> - };
> - };
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - tcsr: syscon@1a400000 {
> - compatible = "qcom,tcsr-ipq8064", "syscon";
> - reg = <0x1a400000 0x100>;
> + status = "disabled";
> };
>
> - l2cc: clock-controller@2011000 {
> - compatible = "qcom,kpss-gcc", "syscon";
> - reg = <0x2011000 0x1000>;
> - clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
> - clock-names = "pll8_vote", "pxo";
> - clock-output-names = "acpu_l2_aux";
> - };
> + sata_phy: sata-phy@1b400000 {
> + compatible = "qcom,ipq806x-sata-phy";
> + reg = <0x1b400000 0x200>;
>
> - lcc: clock-controller@28000000 {
> - compatible = "qcom,lcc-ipq8064";
> - reg = <0x28000000 0x1000>;
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> + clocks = <&gcc SATA_PHY_CFG_CLK>;
> + clock-names = "cfg";
> +
> + #phy-cells = <0>;
> + status = "disabled";
> };
>
> pcie0: pci@1b500000 {
> @@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 {
> perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
> };
>
> - nss_common: syscon@03000000 {
> - compatible = "syscon";
> - reg = <0x03000000 0x0000FFFF>;
> - };
> -
> qsgmii_csr: syscon@1bb00000 {
> compatible = "syscon";
> reg = <0x1bb00000 0x000001FF>;
> };
>
> - stmmac_axi_setup: stmmac-axi-config {
> - snps,wr_osr_lmt = <7>;
> - snps,rd_osr_lmt = <7>;
> - snps,blen = <16 0 0 0 0 0 0>;
> + lcc: clock-controller@28000000 {
> + compatible = "qcom,lcc-ipq8064";
> + reg = <0x28000000 0x1000>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + lpass@28100000 {
> + compatible = "qcom,lpass-cpu";
> + status = "disabled";
> + clocks = <&lcc AHBIX_CLK>,
> + <&lcc MI2S_OSR_CLK>,
> + <&lcc MI2S_BIT_CLK>;
> + clock-names = "ahbix-clk",
> + "mi2s-osr-clk",
> + "mi2s-bit-clk";
> + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "lpass-irq-lpaif";
> + reg = <0x28100000 0x10000>;
> + reg-names = "lpass-lpaif";
> + };
> +
> + sata: sata@29000000 {
> + compatible = "qcom,ipq806x-ahci", "generic-ahci";
> + reg = <0x29000000 0x180>;
> +
> + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc SFAB_SATA_S_H_CLK>,
> + <&gcc SATA_H_CLK>,
> + <&gcc SATA_A_CLK>,
> + <&gcc SATA_RXOOB_CLK>,
> + <&gcc SATA_PMALIVE_CLK>;
> + clock-names = "slave_face", "iface", "core",
> + "rxoob", "pmalive";
> +
> + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
> + assigned-clock-rates = <100000000>, <100000000>;
> +
> + phys = <&sata_phy>;
> + phy-names = "sata-phy";
> + status = "disabled";
> };
>
> gmac0: ethernet@37000000 {
> @@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 {
>
> status = "disabled";
> };
> -
> - hs_phy_0: phy@100f8800 {
> - compatible = "qcom,ipq806x-usb-phy-hs";
> - reg = <0x100f8800 0x30>;
> - clocks = <&gcc USB30_0_UTMI_CLK>;
> - clock-names = "ref";
> - #phy-cells = <0>;
> -
> - status = "disabled";
> - };
> -
> - ss_phy_0: phy@100f8830 {
> - compatible = "qcom,ipq806x-usb-phy-ss";
> - reg = <0x100f8830 0x30>;
> - clocks = <&gcc USB30_0_MASTER_CLK>;
> - clock-names = "ref";
> - #phy-cells = <0>;
> -
> - status = "disabled";
> - };
> -
> - usb3_0: usb3@100f8800 {
> - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <0x100f8800 0x8000>;
> - clocks = <&gcc USB30_0_MASTER_CLK>;
> - clock-names = "core";
> -
> - ranges;
> -
> - resets = <&gcc USB30_0_MASTER_RESET>;
> - reset-names = "master";
> -
> - status = "disabled";
> -
> - dwc3_0: dwc3@10000000 {
> - compatible = "snps,dwc3";
> - reg = <0x10000000 0xcd00>;
> - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> - phys = <&hs_phy_0>, <&ss_phy_0>;
> - phy-names = "usb2-phy", "usb3-phy";
> - dr_mode = "host";
> - snps,dis_u3_susphy_quirk;
> - };
> - };
> -
> - hs_phy_1: phy@110f8800 {
> - compatible = "qcom,ipq806x-usb-phy-hs";
> - reg = <0x110f8800 0x30>;
> - clocks = <&gcc USB30_1_UTMI_CLK>;
> - clock-names = "ref";
> - #phy-cells = <0>;
> -
> - status = "disabled";
> - };
> -
> - ss_phy_1: phy@110f8830 {
> - compatible = "qcom,ipq806x-usb-phy-ss";
> - reg = <0x110f8830 0x30>;
> - clocks = <&gcc USB30_1_MASTER_CLK>;
> - clock-names = "ref";
> - #phy-cells = <0>;
> -
> - status = "disabled";
> - };
> -
> - usb3_1: usb3@110f8800 {
> - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - reg = <0x110f8800 0x8000>;
> - clocks = <&gcc USB30_1_MASTER_CLK>;
> - clock-names = "core";
> -
> - ranges;
> -
> - resets = <&gcc USB30_1_MASTER_RESET>;
> - reset-names = "master";
> -
> - status = "disabled";
> -
> - dwc3_1: dwc3@11000000 {
> - compatible = "snps,dwc3";
> - reg = <0x11000000 0xcd00>;
> - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> - phys = <&hs_phy_1>, <&ss_phy_1>;
> - phy-names = "usb2-phy", "usb3-phy";
> - dr_mode = "host";
> - snps,dis_u3_susphy_quirk;
> - };
> - };
> -
> - vsdcc_fixed: vsdcc-regulator {
> - compatible = "regulator-fixed";
> - regulator-name = "SDCC Power";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - sdcc1bam: dma-controller@12402000 {
> - compatible = "qcom,bam-v1.3.0";
> - reg = <0x12402000 0x8000>;
> - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&gcc SDC1_H_CLK>;
> - clock-names = "bam_clk";
> - #dma-cells = <1>;
> - qcom,ee = <0>;
> - };
> -
> - sdcc3bam: dma-controller@12182000 {
> - compatible = "qcom,bam-v1.3.0";
> - reg = <0x12182000 0x8000>;
> - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&gcc SDC3_H_CLK>;
> - clock-names = "bam_clk";
> - #dma-cells = <1>;
> - qcom,ee = <0>;
> - };
> -
> - amba: amba {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - sdcc1: mmc@12400000 {
> - status = "disabled";
> - compatible = "arm,pl18x", "arm,primecell";
> - arm,primecell-periphid = <0x00051180>;
> - reg = <0x12400000 0x2000>;
> - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "cmd_irq";
> - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
> - clock-names = "mclk", "apb_pclk";
> - bus-width = <8>;
> - max-frequency = <96000000>;
> - non-removable;
> - cap-sd-highspeed;
> - cap-mmc-highspeed;
> - mmc-ddr-1_8v;
> - vmmc-supply = <&vsdcc_fixed>;
> - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
> - dma-names = "tx", "rx";
> - };
> -
> - sdcc3: mmc@12180000 {
> - compatible = "arm,pl18x", "arm,primecell";
> - arm,primecell-periphid = <0x00051180>;
> - status = "disabled";
> - reg = <0x12180000 0x2000>;
> - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "cmd_irq";
> - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
> - clock-names = "mclk", "apb_pclk";
> - bus-width = <8>;
> - cap-sd-highspeed;
> - cap-mmc-highspeed;
> - max-frequency = <192000000>;
> - sd-uhs-sdr104;
> - sd-uhs-ddr50;
> - vqmmc-supply = <&vsdcc_fixed>;
> - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
> - dma-names = "tx", "rx";
> - };
> - };
> -
> - sfpb_mutex: hwlock@1200600 {
> - compatible = "qcom,sfpb-mutex";
> - reg = <0x01200600 0x100>;
> -
> - #hwlock-cells = <1>;
> - };
> };
> };
> --
> 2.36.1
>
--
Ansuel