[PATCH 5.19 0169/1157] ARM: dts: BCM5301X: Add DT for Meraki MR26

From: Greg Kroah-Hartman
Date: Mon Aug 15 2022 - 18:35:24 EST

From: Christian Lamparter <chunkeey@xxxxxxxxx>

[ Upstream commit 935327a73553001f8d81375c76985d05f604507f ]

Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.

Thank you Amir for the unit and PSU.

Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor

SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.

Odd stuff:

- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.

WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]

Signed-off-by: Christian Lamparter <chunkeey@xxxxxxxxx>
Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm53015-meraki-mr26.dts | 166 +++++++++++++++++++++
2 files changed, 167 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm53015-meraki-mr26.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5112f493f494..27eec8e670ec 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -135,6 +135,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm47094-luxul-xwr-3150-v1.dtb \
bcm47094-netgear-r8500.dtb \
bcm47094-phicomm-k3.dtb \
+ bcm53015-meraki-mr26.dtb \
bcm53016-meraki-mr32.dtb \
bcm94708.dtb \
bcm94709.dtb \
diff --git a/arch/arm/boot/dts/bcm53015-meraki-mr26.dts b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
new file mode 100644
index 000000000000..14f58033efeb
--- /dev/null
+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@xxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+ model = "Meraki MR26";
+
+ memory@0 {
+ reg = <0x00000000 0x08000000>;
+ device_type = "memory";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_FAULT;
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+ led-1 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ key-restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ clock-frequency = <50000000>;
+ /delete-property/ clocks;
+};
+
+&uart1 {
+ status = "disabled";
+};
+
+&gmac0 {
+ status = "okay";
+};
+
+&gmac1 {
+ status = "disabled";
+};
+&gmac2 {
+ status = "disabled";
+};
+&gmac3 {
+ status = "disabled";
+};
+
+&nandcs {
+ nand-ecc-algo = "hw";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x200000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "u-boot-env";
+ reg = <0x200000 0x200000>;
+ /* empty */
+ };
+
+ partition@400000 {
+ label = "u-boot-backup";
+ reg = <0x400000 0x200000>;
+ /* empty */
+ };
+
+ partition@600000 {
+ label = "u-boot-env-backup";
+ reg = <0x600000 0x200000>;
+ /* empty */
+ };
+
+ partition@800000 {
+ label = "ubi";
+ reg = <0x800000 0x7780000>;
+ };
+ };
+};
+
+&srab {
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+ label = "poe";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+
+ fixed-link {
+ speed = <1000>;
+ duplex-full;
+ };
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinmux_i2c>;
+
+ clock-frequency = <100000>;
+
+ ina219@40 {
+ compatible = "ti,ina219"; /* PoE power */
+ reg = <0x40>;
+ shunt-resistor = <60000>; /* = 60 mOhms */
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ pagesize = <32>;
+ read-only;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* it's empty */
+ };
+};
+
+&thermal {
+ status = "disabled";
+ /* does not work, reads 418 degree Celsius */
+};
--
2.35.1