[PATCH v2 2/2] drivers: iio: accel adxl312 and adxl314 support
From: George Mois
Date: Tue Aug 23 2022 - 06:53:18 EST
ADXL312 and ADXL314 are small, thin, low power, 3-axis accelerometers
with high resolution (13-bit) measurement up to +/-12 g and +/- 200 g
respectively.
Implement support for ADXL312 and ADXL314 by extending the ADXL313
driver.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL312.pdf
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL314.pdf
Signed-off-by: George Mois <george.mois@xxxxxxxxxx>
---
changes in v2:
- extend the adxl313_of_match table with chip type specific data
- remove SPI bus header file in core driver
- remove accidental revert in adxl313_data structure
- use chip type specific data for decisions within the driver
- warn instead of fails when chip ID does not match expected chip ID
for specific device
- remove noise in the log
- replace magic numbers with defines
- update namespacing with new exports to the same adxl313_of_match
- add I2C support
drivers/iio/accel/adxl313.h | 24 ++++-
drivers/iio/accel/adxl313_core.c | 174 +++++++++++++++++++++++--------
drivers/iio/accel/adxl313_i2c.c | 47 ++++++---
drivers/iio/accel/adxl313_spi.c | 59 +++++++----
4 files changed, 223 insertions(+), 81 deletions(-)
diff --git a/drivers/iio/accel/adxl313.h b/drivers/iio/accel/adxl313.h
index 4415f2fc07e1..854bae97c97c 100644
--- a/drivers/iio/accel/adxl313.h
+++ b/drivers/iio/accel/adxl313.h
@@ -26,6 +26,7 @@
#define ADXL313_REG_FIFO_STATUS 0x39
#define ADXL313_DEVID0 0xAD
+#define ADXL313_DEVID0_ADXL312_314 0xE5
#define ADXL313_DEVID1 0x1D
#define ADXL313_PARTID 0xCB
#define ADXL313_SOFT_RESET 0x52
@@ -37,18 +38,37 @@
#define ADXL313_MEASUREMENT_MODE BIT(3)
#define ADXL313_RANGE_MSK GENMASK(1, 0)
-#define ADXL313_RANGE_4G 3
+#define ADXL313_RANGE_MAX 3
#define ADXL313_FULL_RES BIT(3)
#define ADXL313_SPI_3WIRE BIT(6)
#define ADXL313_I2C_DISABLE BIT(6)
+extern const struct regmap_access_table adxl312_readable_regs_table;
extern const struct regmap_access_table adxl313_readable_regs_table;
+extern const struct regmap_access_table adxl314_readable_regs_table;
+extern const struct regmap_access_table adxl312_writable_regs_table;
extern const struct regmap_access_table adxl313_writable_regs_table;
+extern const struct regmap_access_table adxl314_writable_regs_table;
+
+extern const struct of_device_id adxl313_of_match[];
+
+enum adxl313_device_type {
+ ADXL312,
+ ADXL313,
+ ADXL314,
+};
+
+struct adxl313_chip_info {
+ const char *name;
+ enum adxl313_device_type type;
+ int scale_factor;
+ bool variable_range;
+ bool soft_reset;
+};
int adxl313_core_probe(struct device *dev,
struct regmap *regmap,
- const char *name,
int (*setup)(struct device *, struct regmap *));
#endif /* _ADXL313_H_ */
diff --git a/drivers/iio/accel/adxl313_core.c b/drivers/iio/accel/adxl313_core.c
index afeef779e1d0..ecb6eef1e197 100644
--- a/drivers/iio/accel/adxl313_core.c
+++ b/drivers/iio/accel/adxl313_core.c
@@ -14,6 +14,13 @@
#include "adxl313.h"
+static const struct regmap_range adxl312_readable_reg_range[] = {
+ regmap_reg_range(ADXL313_REG_DEVID0, ADXL313_REG_DEVID0),
+ regmap_reg_range(ADXL313_REG_OFS_AXIS(0), ADXL313_REG_OFS_AXIS(2)),
+ regmap_reg_range(ADXL313_REG_THRESH_ACT, ADXL313_REG_ACT_INACT_CTL),
+ regmap_reg_range(ADXL313_REG_BW_RATE, ADXL313_REG_FIFO_STATUS),
+};
+
static const struct regmap_range adxl313_readable_reg_range[] = {
regmap_reg_range(ADXL313_REG_DEVID0, ADXL313_REG_XID),
regmap_reg_range(ADXL313_REG_SOFT_RESET, ADXL313_REG_SOFT_RESET),
@@ -22,12 +29,74 @@ static const struct regmap_range adxl313_readable_reg_range[] = {
regmap_reg_range(ADXL313_REG_BW_RATE, ADXL313_REG_FIFO_STATUS),
};
+const struct regmap_access_table adxl312_readable_regs_table = {
+ .yes_ranges = adxl312_readable_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl312_readable_reg_range),
+};
+EXPORT_SYMBOL_NS_GPL(adxl312_readable_regs_table, IIO_ADXL313);
+
const struct regmap_access_table adxl313_readable_regs_table = {
.yes_ranges = adxl313_readable_reg_range,
.n_yes_ranges = ARRAY_SIZE(adxl313_readable_reg_range),
};
EXPORT_SYMBOL_NS_GPL(adxl313_readable_regs_table, IIO_ADXL313);
+const struct regmap_access_table adxl314_readable_regs_table = {
+ .yes_ranges = adxl312_readable_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl312_readable_reg_range),
+};
+EXPORT_SYMBOL_NS_GPL(adxl314_readable_regs_table, IIO_ADXL313);
+
+static const struct adxl313_chip_info adxl31x_chip_info[] = {
+ [ADXL312] = {
+ .name = "adxl312",
+ .type = ADXL312,
+ .scale_factor = 28425072,
+ .variable_range = true,
+ .soft_reset = false,
+ },
+ [ADXL313] = {
+ .name = "adxl313",
+ .type = ADXL313,
+ .scale_factor = 9576806,
+ .variable_range = true,
+ .soft_reset = true,
+ },
+ [ADXL314] = {
+ .name = "adxl314",
+ .type = ADXL314,
+ .scale_factor = 478858719,
+ .variable_range = false,
+ .soft_reset = false,
+ }
+};
+
+const struct of_device_id adxl313_of_match[] = {
+ {
+ .compatible = "adi,adxl312",
+ .data = &adxl31x_chip_info[ADXL312],
+ },
+ {
+ .compatible = "adi,adxl313",
+ .data = &adxl31x_chip_info[ADXL313],
+ },
+ {
+ .compatible = "adi,adxl314",
+ .data = &adxl31x_chip_info[ADXL314],
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(of, adxl313_of_match);
+EXPORT_SYMBOL_NS_GPL(adxl313_of_match, IIO_ADXL313);
+
+static const struct regmap_range adxl312_writable_reg_range[] = {
+ regmap_reg_range(ADXL313_REG_OFS_AXIS(0), ADXL313_REG_OFS_AXIS(2)),
+ regmap_reg_range(ADXL313_REG_THRESH_ACT, ADXL313_REG_ACT_INACT_CTL),
+ regmap_reg_range(ADXL313_REG_BW_RATE, ADXL313_REG_INT_MAP),
+ regmap_reg_range(ADXL313_REG_DATA_FORMAT, ADXL313_REG_DATA_FORMAT),
+ regmap_reg_range(ADXL313_REG_FIFO_CTL, ADXL313_REG_FIFO_CTL),
+};
+
static const struct regmap_range adxl313_writable_reg_range[] = {
regmap_reg_range(ADXL313_REG_SOFT_RESET, ADXL313_REG_SOFT_RESET),
regmap_reg_range(ADXL313_REG_OFS_AXIS(0), ADXL313_REG_OFS_AXIS(2)),
@@ -37,14 +106,27 @@ static const struct regmap_range adxl313_writable_reg_range[] = {
regmap_reg_range(ADXL313_REG_FIFO_CTL, ADXL313_REG_FIFO_CTL),
};
+const struct regmap_access_table adxl312_writable_regs_table = {
+ .yes_ranges = adxl312_writable_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl312_writable_reg_range),
+};
+EXPORT_SYMBOL_NS_GPL(adxl312_writable_regs_table, IIO_ADXL313);
+
const struct regmap_access_table adxl313_writable_regs_table = {
.yes_ranges = adxl313_writable_reg_range,
.n_yes_ranges = ARRAY_SIZE(adxl313_writable_reg_range),
};
EXPORT_SYMBOL_NS_GPL(adxl313_writable_regs_table, IIO_ADXL313);
+const struct regmap_access_table adxl314_writable_regs_table = {
+ .yes_ranges = adxl312_writable_reg_range,
+ .n_yes_ranges = ARRAY_SIZE(adxl312_writable_reg_range),
+};
+EXPORT_SYMBOL_NS_GPL(adxl314_writable_regs_table, IIO_ADXL313);
+
struct adxl313_data {
struct regmap *regmap;
+ const struct adxl313_chip_info *chip_info;
struct mutex lock; /* lock to protect transf_buf */
__le16 transf_buf __aligned(IIO_DMA_MINALIGN);
};
@@ -156,12 +238,10 @@ static int adxl313_read_raw(struct iio_dev *indio_dev,
*val = sign_extend32(ret, chan->scan_type.realbits - 1);
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
- /*
- * Scale for any g range is given in datasheet as
- * 1024 LSB/g = 0.0009765625 * 9.80665 = 0.009576806640625 m/s^2
- */
*val = 0;
- *val2 = 9576806;
+
+ *val2 = data->chip_info->scale_factor;
+
return IIO_VAL_INT_PLUS_NANO;
case IIO_CHAN_INFO_CALIBBIAS:
ret = regmap_read(data->regmap,
@@ -170,7 +250,7 @@ static int adxl313_read_raw(struct iio_dev *indio_dev,
return ret;
/*
- * 8-bit resolution at +/- 0.5g, that is 4x accel data scale
+ * 8-bit resolution at minimum range, that is 4x accel data scale
* factor at full resolution
*/
*val = sign_extend32(regval, 7) * 4;
@@ -198,7 +278,7 @@ static int adxl313_write_raw(struct iio_dev *indio_dev,
switch (mask) {
case IIO_CHAN_INFO_CALIBBIAS:
/*
- * 8-bit resolution at +/- 0.5g, that is 4x accel data scale
+ * 8-bit resolution at minimum range, that is 4x accel data scale
* factor at full resolution
*/
if (clamp_val(val, -128 * 4, 127 * 4) != val)
@@ -226,11 +306,15 @@ static int adxl313_setup(struct device *dev, struct adxl313_data *data,
unsigned int regval;
int ret;
- /* Ensures the device is in a consistent state after start up */
- ret = regmap_write(data->regmap, ADXL313_REG_SOFT_RESET,
- ADXL313_SOFT_RESET);
- if (ret)
- return ret;
+ /* If sw reset available, ensures the device is in a consistent
+ * state after start up
+ */
+ if (data->chip_info->soft_reset) {
+ ret = regmap_write(data->regmap, ADXL313_REG_SOFT_RESET,
+ ADXL313_SOFT_RESET);
+ if (ret)
+ return ret;
+ }
if (setup) {
ret = setup(dev, data->regmap);
@@ -242,41 +326,44 @@ static int adxl313_setup(struct device *dev, struct adxl313_data *data,
if (ret)
return ret;
- if (regval != ADXL313_DEVID0) {
- dev_err(dev, "Invalid manufacturer ID: 0x%02x\n", regval);
- return -ENODEV;
- }
+ if (data->chip_info->type == ADXL313 && regval != ADXL313_DEVID0)
+ dev_warn(dev, "Invalid manufacturer ID: 0x%02x\n", regval);
- ret = regmap_read(data->regmap, ADXL313_REG_DEVID1, ®val);
- if (ret)
- return ret;
+ /* If ADXL313, check DEVID1 and PARTID */
+ if (regval == ADXL313_DEVID0) {
+ ret = regmap_read(data->regmap, ADXL313_REG_DEVID1, ®val);
+ if (ret)
+ return ret;
- if (regval != ADXL313_DEVID1) {
- dev_err(dev, "Invalid mems ID: 0x%02x\n", regval);
- return -ENODEV;
- }
+ if (regval != ADXL313_DEVID1)
+ dev_warn(dev, "Invalid mems ID: 0x%02x\n", regval);
- ret = regmap_read(data->regmap, ADXL313_REG_PARTID, ®val);
- if (ret)
- return ret;
+ ret = regmap_read(data->regmap, ADXL313_REG_PARTID, ®val);
+ if (ret)
+ return ret;
- if (regval != ADXL313_PARTID) {
- dev_err(dev, "Invalid device ID: 0x%02x\n", regval);
- return -ENODEV;
+ if (regval != ADXL313_PARTID)
+ dev_warn(dev, "Invalid device ID: 0x%02x\n", regval);
}
- /* Sets the range to +/- 4g */
- ret = regmap_update_bits(data->regmap, ADXL313_REG_DATA_FORMAT,
- ADXL313_RANGE_MSK,
- FIELD_PREP(ADXL313_RANGE_MSK, ADXL313_RANGE_4G));
- if (ret)
- return ret;
+ /* If ADXL312 or ADXL314 device, check DEVID0 */
+ if (data->chip_info->type != ADXL313 && regval != ADXL313_DEVID0_ADXL312_314)
+ dev_warn(dev, "Invalid manufacturer ID: %#02x\n", regval);
- /* Enables full resolution */
- ret = regmap_update_bits(data->regmap, ADXL313_REG_DATA_FORMAT,
- ADXL313_FULL_RES, ADXL313_FULL_RES);
- if (ret)
- return ret;
+ /* Sets the range to maximum, full resolution, if applicable */
+ if (data->chip_info->variable_range) {
+ ret = regmap_update_bits(data->regmap, ADXL313_REG_DATA_FORMAT,
+ ADXL313_RANGE_MSK,
+ FIELD_PREP(ADXL313_RANGE_MSK, ADXL313_RANGE_MAX));
+ if (ret)
+ return ret;
+
+ /* Enables full resolution */
+ ret = regmap_update_bits(data->regmap, ADXL313_REG_DATA_FORMAT,
+ ADXL313_FULL_RES, ADXL313_FULL_RES);
+ if (ret)
+ return ret;
+ }
/* Enables measurement mode */
return regmap_update_bits(data->regmap, ADXL313_REG_POWER_CTL,
@@ -288,7 +375,6 @@ static int adxl313_setup(struct device *dev, struct adxl313_data *data,
* adxl313_core_probe() - probe and setup for adxl313 accelerometer
* @dev: Driver model representation of the device
* @regmap: Register map of the device
- * @name: Device name buffer reference
* @setup: Setup routine to be executed right before the standard device
* setup, can also be set to NULL if not required
*
@@ -296,9 +382,9 @@ static int adxl313_setup(struct device *dev, struct adxl313_data *data,
*/
int adxl313_core_probe(struct device *dev,
struct regmap *regmap,
- const char *name,
int (*setup)(struct device *, struct regmap *))
{
+ const struct adxl313_chip_info *chip_data = device_get_match_data(dev);
struct adxl313_data *data;
struct iio_dev *indio_dev;
int ret;
@@ -309,9 +395,11 @@ int adxl313_core_probe(struct device *dev,
data = iio_priv(indio_dev);
data->regmap = regmap;
+ data->chip_info = chip_data;
+
mutex_init(&data->lock);
- indio_dev->name = name;
+ indio_dev->name = chip_data->name;
indio_dev->info = &adxl313_info;
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->channels = adxl313_channels;
diff --git a/drivers/iio/accel/adxl313_i2c.c b/drivers/iio/accel/adxl313_i2c.c
index c329765dbf60..32fb8d4866f8 100644
--- a/drivers/iio/accel/adxl313_i2c.c
+++ b/drivers/iio/accel/adxl313_i2c.c
@@ -14,42 +14,57 @@
#include "adxl313.h"
-static const struct regmap_config adxl313_i2c_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .rd_table = &adxl313_readable_regs_table,
- .wr_table = &adxl313_writable_regs_table,
- .max_register = 0x39,
+static const struct regmap_config adxl31x_i2c_regmap_config[] = {
+ [ADXL312] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl312_readable_regs_table,
+ .wr_table = &adxl312_writable_regs_table,
+ .max_register = 0x39,
+ },
+ [ADXL313] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl313_readable_regs_table,
+ .wr_table = &adxl313_writable_regs_table,
+ .max_register = 0x39,
+ },
+ [ADXL314] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl314_readable_regs_table,
+ .wr_table = &adxl314_writable_regs_table,
+ .max_register = 0x39,
+ }
};
static int adxl313_i2c_probe(struct i2c_client *client)
{
+ const struct adxl313_chip_info *chip_data;
struct regmap *regmap;
- regmap = devm_regmap_init_i2c(client, &adxl313_i2c_regmap_config);
+ chip_data = device_get_match_data(&client->dev);
+
+ regmap = devm_regmap_init_i2c(client,
+ &adxl31x_i2c_regmap_config[chip_data->type]);
if (IS_ERR(regmap)) {
dev_err(&client->dev, "Error initializing i2c regmap: %ld\n",
PTR_ERR(regmap));
return PTR_ERR(regmap);
}
- return adxl313_core_probe(&client->dev, regmap, client->name, NULL);
+ return adxl313_core_probe(&client->dev, regmap, NULL);
}
static const struct i2c_device_id adxl313_i2c_id[] = {
- { "adxl313" },
+ { "adxl312", ADXL312 },
+ { "adxl313", ADXL313 },
+ { "adxl314", ADXL314 },
{ }
};
MODULE_DEVICE_TABLE(i2c, adxl313_i2c_id);
-static const struct of_device_id adxl313_of_match[] = {
- { .compatible = "adi,adxl313" },
- { }
-};
-
-MODULE_DEVICE_TABLE(of, adxl313_of_match);
-
static struct i2c_driver adxl313_i2c_driver = {
.driver = {
.name = "adxl313_i2c",
diff --git a/drivers/iio/accel/adxl313_spi.c b/drivers/iio/accel/adxl313_spi.c
index a3c6d553462d..c22ab02163ed 100644
--- a/drivers/iio/accel/adxl313_spi.c
+++ b/drivers/iio/accel/adxl313_spi.c
@@ -11,17 +11,38 @@
#include <linux/module.h>
#include <linux/regmap.h>
#include <linux/spi/spi.h>
+#include <linux/property.h>
#include "adxl313.h"
-static const struct regmap_config adxl313_spi_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .rd_table = &adxl313_readable_regs_table,
- .wr_table = &adxl313_writable_regs_table,
- .max_register = 0x39,
- /* Setting bits 7 and 6 enables multiple-byte read */
- .read_flag_mask = BIT(7) | BIT(6),
+static const struct regmap_config adxl31x_spi_regmap_config[] = {
+ [ADXL312] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl312_readable_regs_table,
+ .wr_table = &adxl312_writable_regs_table,
+ .max_register = 0x39,
+ /* Setting bits 7 and 6 enables multiple-byte read */
+ .read_flag_mask = BIT(7) | BIT(6),
+ },
+ [ADXL313] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl313_readable_regs_table,
+ .wr_table = &adxl313_writable_regs_table,
+ .max_register = 0x39,
+ /* Setting bits 7 and 6 enables multiple-byte read */
+ .read_flag_mask = BIT(7) | BIT(6),
+ },
+ [ADXL314] = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &adxl314_readable_regs_table,
+ .wr_table = &adxl314_writable_regs_table,
+ .max_register = 0x39,
+ /* Setting bits 7 and 6 enables multiple-byte read */
+ .read_flag_mask = BIT(7) | BIT(6),
+ }
};
static int adxl313_spi_setup(struct device *dev, struct regmap *regmap)
@@ -42,7 +63,7 @@ static int adxl313_spi_setup(struct device *dev, struct regmap *regmap)
static int adxl313_spi_probe(struct spi_device *spi)
{
- const struct spi_device_id *id = spi_get_device_id(spi);
+ const struct adxl313_chip_info *chip_data;
struct regmap *regmap;
int ret;
@@ -51,31 +72,29 @@ static int adxl313_spi_probe(struct spi_device *spi)
if (ret)
return ret;
- regmap = devm_regmap_init_spi(spi, &adxl313_spi_regmap_config);
+ chip_data = device_get_match_data(&spi->dev);
+
+ regmap = devm_regmap_init_spi(spi,
+ &adxl31x_spi_regmap_config[chip_data->type]);
+
if (IS_ERR(regmap)) {
dev_err(&spi->dev, "Error initializing spi regmap: %ld\n",
PTR_ERR(regmap));
return PTR_ERR(regmap);
}
- return adxl313_core_probe(&spi->dev, regmap, id->name,
- &adxl313_spi_setup);
+ return adxl313_core_probe(&spi->dev, regmap, &adxl313_spi_setup);
}
static const struct spi_device_id adxl313_spi_id[] = {
- { "adxl313" },
+ { "adxl312", ADXL312 },
+ { "adxl313", ADXL313 },
+ { "adxl314", ADXL314 },
{ }
};
MODULE_DEVICE_TABLE(spi, adxl313_spi_id);
-static const struct of_device_id adxl313_of_match[] = {
- { .compatible = "adi,adxl313" },
- { }
-};
-
-MODULE_DEVICE_TABLE(of, adxl313_of_match);
-
static struct spi_driver adxl313_spi_driver = {
.driver = {
.name = "adxl313_spi",
--
2.30.2