Re: [PATCH 4/4] arch: arm64: ti: Add support for J784s4 EVM board

[Krzysztof Kozlowski]

On 19/08/2022 22:00, Apurva Nandan wrote:
> J784s4 EVM board is designed for TI J784s4 SoC. It supports the following
> interfaces:
> * 32 GB DDR4 RAM
> * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
> * x1 Input Audio Jack, x1 Output Audio Jack
> * x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
> * x2 4L PCIe connector
> * x1 UHS-1 capable micro-SD card slot
> * 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
>   UFS flash.
> * x6 UART through UART-USB bridge
> * XDS110 for onboard JTAG debug using USB
> * Temperature sensors, user push buttons and LEDs
> * 40-pin User Expansion Connector
> * x2 ENET Expansion Connector, x1 GESI expander, x2 Display connector
> * x1 15-pin CSI header
> * x6 MCAN instances
> 
> Add basic support for J784s4-EVM.
> 
> Schematics: https://www.ti.com/lit/zip/sprr458

Use subject perfixes matching the subsystem (git log --oneline -- ...).
For example:
arm64: dts: ti:

> 
> Signed-off-by: Hari Nagalla <hnagalla@xxxxxx>
> Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
> Signed-off-by: Nishanth Menon <nm@xxxxxx>
> Signed-off-by: Matt Ranostay <mranostay@xxxxxx>
> Signed-off-by: Rahul T R <r-ravikumar@xxxxxx>
> Signed-off-by: Suman Anna <s-anna@xxxxxx>
> Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
> Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
> ---
>  arch/arm64/boot/dts/ti/Makefile          |   2 +
>  arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 602 +++++++++++++++++++++++
>  2 files changed, 604 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> 
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 02e5d80344d0..6381c458738a 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>  
>  dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
>  
> +dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
> +
>  dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>  
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> new file mode 100644
> index 000000000000..7ca08e115e67
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -0,0 +1,602 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + *
> + * Common Processor Board: https://www.ti.com/tool/J721EXCPXEVM
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-j784s4.dtsi"
> +
> +/ {
> +	compatible = "ti,j784s4-evm", "ti,j784s4";
> +	model = "Texas Instruments J784S4 EVM";
> +
> +	chosen {
> +		stdout-path = "serial2:115200n8";
> +		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x2880000";

earlycon is not a property of hardware. Console is defined in
stdout-path, so please drop entire bootargs.

> +	};
> +
> +	aliases {
> +		serial2 = &main_uart8;
> +		mmc0 = &main_sdhci0;
> +		mmc1 = &main_sdhci1;
> +		i2c0 = &main_i2c0;
> +		can0 = &mcu_mcan0;
> +		can1 = &mcu_mcan1;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		/* 32G RAM */
> +		reg = <0x00 0x80000000 0x00 0x80000000>,
> +		      <0x08 0x80000000 0x07 0x80000000>;
> +	};
> +
> +	/* Reserving memory regions still pending */
> +	reserved_memory: reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		secure_ddr: optee@9e800000 {
> +			reg = <0x00 0x9e800000 0x00 0x01800000>;
> +			alignment = <0x1000>;
> +			no-map;
> +		};
> +	};
> +
> +	evm_12v0: fixedregulator-evm12v0 {

Node name should be generic, so:
regulator-evm12v0

> +		/* main supply */
> +		compatible = "regulator-fixed";
> +		regulator-name = "evm_12v0";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vsys_3v3: fixedregulator-vsys3v3 {

ditto

> +		/* Output of LM5140 */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vsys_3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&evm_12v0>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vsys_5v0: fixedregulator-vsys5v0 {

ditto

> +		/* Output of LM5140 */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vsys_5v0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&evm_12v0>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vdd_mmc1: fixedregulator-sd {

ditto

> +		/* Output of TPS22918 */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_mmc1";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		enable-active-high;
> +		vin-supply = <&vsys_3v3>;
> +		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	vdd_sd_dv: gpio-regulator-TLV71033 {

ditto

> +		/* Output of TLV71033 */
> +		compatible = "regulator-gpio";
> +		regulator-name = "tlv71033";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vdd_sd_dv_pins_default>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		vin-supply = <&vsys_5v0>;
> +		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x0>,
> +			 <3300000 0x1>;
> +	};
> +
> +	transceiver1: can-phy1 {
> +		compatible = "ti,tcan1042";
> +		#phy-cells = <0>;
> +		max-bitrate = <5000000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
> +		standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	transceiver2: can-phy2 {
> +		compatible = "ti,tcan1042";
> +		#phy-cells = <0>;
> +		max-bitrate = <5000000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
> +		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
> +	};



Best regards,
Krzysztof