Re: [PATCH net-next v4 0/8] [RFT] net: dpaa: Convert to phylink

[Sean Anderson]

On 8/4/22 3:46 PM, Sean Anderson wrote:
> This series converts the DPAA driver to phylink.
> 
> I have tried to maintain backwards compatibility with existing device
> trees whereever possible. However, one area where I was unable to
> achieve this was with QSGMII. Please refer to patch 2 for details.
> 
> All mac drivers have now been converted. I would greatly appreciate if
> anyone has T-series or P-series boards they can test/debug this series
> on. I only have an LS1046ARDB. Everything but QSGMII should work without
> breakage; QSGMII needs patches 7 and 8. For this reason, the last 4
> patches in this series should be applied together (and should not go
> through separate trees).
> 
> This series depends on [1] and [2].
> 
> [1] https://lore.kernel.org/netdev/20220725153730.2604096-1-sean.anderson@xxxxxxxx/
> [2] https://lore.kernel.org/netdev/20220725151039.2581576-1-sean.anderson@xxxxxxxx/
> 
> Changes in v4:
> - Use pcs-handle-names instead of pcs-names, as discussed
> - Don't fail if phy support was not compiled in
> - Split off rate adaptation series
> - Split off DPAA "preparation" series
> - Split off Lynx 10G support
> - t208x: Mark MAC1 and MAC2 as 10G
> - Add XFI PCS for t208x MAC1/MAC2
> 
> Changes in v3:
> - Expand pcs-handle to an array
> - Add vendor prefix 'fsl,' to rgmii and mii properties.
> - Set maxItems for pcs-names
> - Remove phy-* properties from example because dt-schema complains and I
>   can't be bothered to figure out how to make it work.
> - Add pcs-handle as a preferred version of pcsphy-handle
> - Deprecate pcsphy-handle
> - Remove mii/rmii properties
> - Put the PCS mdiodev only after we are done with it (since the PCS
>   does not perform a get itself).
> - Remove _return label from memac_initialization in favor of returning
>   directly
> - Fix grabbing the default PCS not checking for -ENODATA from
>   of_property_match_string
> - Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config
> - Remove rmii/mii properties
> - Replace 1000Base... with 1000BASE... to match IEEE capitalization
> - Add compatibles for QSGMII PCSs
> - Split arm and powerpcs dts updates
> 
> Changes in v2:
> - Better document how we select which PCS to use in the default case
> - Move PCS_LYNX dependency to fman Kconfig
> - Remove unused variable slow_10g_if
> - Restrict valid link modes based on the phy interface. This is easier
>   to set up, and mostly captures what I intended to do the first time.
>   We now have a custom validate which restricts half-duplex for some SoCs
>   for RGMII, but generally just uses the default phylink validate.
> - Configure the SerDes in enable/disable
> - Properly implement all ethtool ops and ioctls. These were mostly
>   stubbed out just enough to compile last time.
> - Convert 10GEC and dTSEC as well
> - Fix capitalization of mEMAC in commit messages
> - Add nodes for QSGMII PCSs
> - Add nodes for QSGMII PCSs
> 
> Sean Anderson (8):
>   dt-bindings: net: Expand pcs-handle to an array
>   dt-bindings: net: fman: Add additional interface properties
>   net: fman: memac: Add serdes support
>   net: fman: memac: Use lynx pcs driver
>   net: dpaa: Convert to phylink
>   powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
>   powerpc: dts: qoriq: Add nodes for QSGMII PCSs
>   arm64: dts: layerscape: Add nodes for QSGMII PCSs
> 
>  .../bindings/net/dsa/renesas,rzn1-a5psw.yaml  |   1 +
>  .../bindings/net/ethernet-controller.yaml     |  10 +-
>  .../bindings/net/fsl,fman-dtsec.yaml          |  53 +-
>  .../bindings/net/fsl,qoriq-mc-dpmac.yaml      |   2 +-
>  .../devicetree/bindings/net/fsl-fman.txt      |   5 +-
>  .../boot/dts/freescale/fsl-ls1043-post.dtsi   |  24 +
>  .../boot/dts/freescale/fsl-ls1046-post.dtsi   |  25 +
>  .../fsl/qoriq-fman3-0-10g-0-best-effort.dtsi  |   3 +-
>  .../boot/dts/fsl/qoriq-fman3-0-10g-0.dtsi     |  10 +-
>  .../fsl/qoriq-fman3-0-10g-1-best-effort.dtsi  |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-0-10g-1.dtsi     |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi     |  45 ++
>  .../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi     |  45 ++
>  .../boot/dts/fsl/qoriq-fman3-0-1g-0.dtsi      |   3 +-
>  .../boot/dts/fsl/qoriq-fman3-0-1g-1.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-0-1g-2.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-0-1g-3.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-0-1g-4.dtsi      |   3 +-
>  .../boot/dts/fsl/qoriq-fman3-0-1g-5.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-10g-0.dtsi     |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-10g-1.dtsi     |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-0.dtsi      |   3 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-1.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-2.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-3.dtsi      |  10 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-4.dtsi      |   3 +-
>  .../boot/dts/fsl/qoriq-fman3-1-1g-5.dtsi      |  10 +-
>  arch/powerpc/boot/dts/fsl/t2081si-post.dtsi   |   4 +-
>  drivers/net/ethernet/freescale/dpaa/Kconfig   |   4 +-
>  .../net/ethernet/freescale/dpaa/dpaa_eth.c    |  89 +--
>  .../ethernet/freescale/dpaa/dpaa_ethtool.c    |  90 +--
>  drivers/net/ethernet/freescale/fman/Kconfig   |   4 +-
>  .../net/ethernet/freescale/fman/fman_dtsec.c  | 459 +++++------
>  .../net/ethernet/freescale/fman/fman_mac.h    |  10 -
>  .../net/ethernet/freescale/fman/fman_memac.c  | 746 +++++++++---------
>  .../net/ethernet/freescale/fman/fman_tgec.c   | 131 ++-
>  drivers/net/ethernet/freescale/fman/mac.c     | 168 +---
>  drivers/net/ethernet/freescale/fman/mac.h     |  23 +-
>  38 files changed, 1033 insertions(+), 1050 deletions(-)
>  create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>  create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
> 

ping?

This will not apply on net-next/master, so I will resend sometime soon,
but does anyone have any feedback first?

--Sean