[PATCH v2] hwmon: (aquacomputer_d5next) Add support for Aquacomputer High Flow Next
From: Aleksa Savic
Date: Wed Sep 07 2022 - 06:10:29 EST
Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.
The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.
Additionally, serial number and firmware version are exposed through
debugfs.
Registry offsets were discovered and tested by users on Github [1] [2].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34
Signed-off-by: Aleksa Savic <savicaleksa83@xxxxxxxxx>
---
Changes in v2:
- Rebased code and docs properly
---
Documentation/hwmon/aquacomputer_d5next.rst | 5 ++
drivers/hwmon/Kconfig | 6 +-
drivers/hwmon/aquacomputer_d5next.c | 91 ++++++++++++++++++++-
3 files changed, 96 insertions(+), 6 deletions(-)
diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
index b63a78d47624..e238533b5fe0 100644
--- a/Documentation/hwmon/aquacomputer_d5next.rst
+++ b/Documentation/hwmon/aquacomputer_d5next.rst
@@ -10,6 +10,7 @@ Supported devices:
* Aquacomputer Farbwerk 360 RGB controller
* Aquacomputer Octo fan controller
* Aquacomputer Quadro fan controller
+* Aquacomputer High Flow Next sensor
Author: Aleksa Savic
@@ -43,6 +44,10 @@ voltage and current.
The Farbwerk and Farbwerk 360 expose four temperature sensors. Additionally,
sixteen virtual temperature sensors of the Farbwerk 360 are exposed.
+The High Flow Next exposes +5V voltages, water quality, conductivity and flow readings.
+A temperature sensor can be connected to it, in which case it provides its reading
+and an estimation of the dissipated/absorbed power in the liquid cooling loop.
+
Depending on the device, not all sysfs and debugfs entries will be available.
Writing to virtual temperature sensors is not currently supported.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index d317aae183c1..18dc045d3fc5 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -257,14 +257,14 @@ config SENSORS_AHT10
will be called aht10.
config SENSORS_AQUACOMPUTER_D5NEXT
- tristate "Aquacomputer D5 Next, Octo, Quadro, Farbwerk, and Farbwerk 360"
+ tristate "Aquacomputer D5 Next, Octo, Quadro, Farbwerk, Farbwerk 360, High Flow Next"
depends on USB_HID
select CRC16
help
If you say yes here you get support for sensors and fans of
the Aquacomputer D5 Next watercooling pump, Octo and Quadro fan
- controllers, Farbwerk and Farbwerk 360 RGB controllers, where
- available.
+ controllers, Farbwerk and Farbwerk 360 RGB controllers, High Flow
+ Next sensor, where available.
This driver can also be built as a module. If so, the module
will be called aquacomputer_d5next.
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index b2b0c4fdfa84..3ea25edfc7a5 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0+
/*
* hwmon driver for Aquacomputer devices (D5 Next, Farbwerk, Farbwerk 360, Octo,
- * Quadro)
+ * Quadro, High Flow Next)
*
* Aquacomputer devices send HID reports (with ID 0x01) every second to report
* sensor values.
@@ -26,15 +26,17 @@
#define USB_PRODUCT_ID_D5NEXT 0xf00e
#define USB_PRODUCT_ID_FARBWERK360 0xf010
#define USB_PRODUCT_ID_OCTO 0xf011
+#define USB_PRODUCT_ID_HIGHFLOWNEXT 0xf012
-enum kinds { d5next, farbwerk, farbwerk360, octo, quadro };
+enum kinds { d5next, farbwerk, farbwerk360, octo, quadro, highflownext };
static const char *const aqc_device_names[] = {
[d5next] = "d5next",
[farbwerk] = "farbwerk",
[farbwerk360] = "farbwerk360",
[octo] = "octo",
- [quadro] = "quadro"
+ [quadro] = "quadro",
+ [highflownext] = "highflownext"
};
#define DRIVER_NAME "aquacomputer_d5next"
@@ -120,6 +122,16 @@ static u8 quadro_sensor_fan_offsets[] = { 0x70, 0x7D, 0x8A, 0x97 };
/* Fan speed registers in Quadro control report (from 0-100%) */
static u16 quadro_ctrl_fan_offsets[] = { 0x36, 0x8b, 0xe0, 0x135 };
+/* Register offsets for the High Flow Next */
+#define HIGHFLOWNEXT_NUM_SENSORS 2
+#define HIGHFLOWNEXT_SENSOR_START 85
+#define HIGHFLOWNEXT_FLOW 81
+#define HIGHFLOWNEXT_WATER_QUALITY 89
+#define HIGHFLOWNEXT_POWER 91
+#define HIGHFLOWNEXT_CONDUCTIVITY 95
+#define HIGHFLOWNEXT_5V_VOLTAGE 97
+#define HIGHFLOWNEXT_5V_VOLTAGE_USB 99
+
/* Labels for D5 Next */
static const char *const label_d5next_temp[] = {
"Coolant temp"
@@ -228,6 +240,27 @@ static const char *const label_quadro_speeds[] = {
"Flow speed [dL/h]"
};
+/* Labels for High Flow Next */
+static const char *const label_highflownext_temp_sensors[] = {
+ "Coolant temp",
+ "External sensor"
+};
+
+static const char *const label_highflownext_fan_speed[] = {
+ "Flow [dL/h]",
+ "Water quality [%]",
+ "Conductivity [nS/cm]",
+};
+
+static const char *const label_highflownext_power[] = {
+ "Dissipated power",
+};
+
+static const char *const label_highflownext_voltage[] = {
+ "+5V voltage",
+ "+5V USB voltage"
+};
+
struct aqc_data {
struct hid_device *hdev;
struct device *hwmon_dev;
@@ -390,6 +423,11 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
break;
case hwmon_fan:
switch (priv->kind) {
+ case highflownext:
+ /* Special case to support flow sensor, water quality and conductivity */
+ if (channel < 3)
+ return 0444;
+ break;
case quadro:
/* Special case to support flow sensor */
if (channel < priv->num_fans + 1)
@@ -402,6 +440,18 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
}
break;
case hwmon_power:
+ switch (priv->kind) {
+ case highflownext:
+ /* Special case to support one power sensor */
+ if (channel == 0)
+ return 0444;
+ break;
+ default:
+ if (channel < priv->num_fans)
+ return 0444;
+ break;
+ }
+ break;
case hwmon_curr:
if (channel < priv->num_fans)
return 0444;
@@ -413,6 +463,11 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
if (channel < priv->num_fans + 2)
return 0444;
break;
+ case highflownext:
+ /* Special case to support two voltage sensors */
+ if (channel < 2)
+ return 0444;
+ break;
default:
if (channel < priv->num_fans)
return 0444;
@@ -679,6 +734,22 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
case quadro:
priv->speed_input[4] = get_unaligned_be16(data + priv->flow_sensor_offset);
break;
+ case highflownext:
+ /* If external temp sensor is not connected, its power reading is also N/A */
+ if (priv->temp_input[1] == -ENODATA)
+ priv->power_input[0] = -ENODATA;
+ else
+ priv->power_input[0] =
+ get_unaligned_be16(data + HIGHFLOWNEXT_POWER) * 1000000;
+
+ priv->voltage_input[0] = get_unaligned_be16(data + HIGHFLOWNEXT_5V_VOLTAGE) * 10;
+ priv->voltage_input[1] =
+ get_unaligned_be16(data + HIGHFLOWNEXT_5V_VOLTAGE_USB) * 10;
+
+ priv->speed_input[0] = get_unaligned_be16(data + HIGHFLOWNEXT_FLOW);
+ priv->speed_input[1] = get_unaligned_be16(data + HIGHFLOWNEXT_WATER_QUALITY);
+ priv->speed_input[2] = get_unaligned_be16(data + HIGHFLOWNEXT_CONDUCTIVITY);
+ break;
default:
break;
}
@@ -851,6 +922,19 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->voltage_label = label_fan_voltage;
priv->current_label = label_fan_current;
break;
+ case USB_PRODUCT_ID_HIGHFLOWNEXT:
+ priv->kind = highflownext;
+
+ priv->num_fans = 0;
+ priv->num_temp_sensors = HIGHFLOWNEXT_NUM_SENSORS;
+ priv->temp_sensor_start_offset = HIGHFLOWNEXT_SENSOR_START;
+ priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
+
+ priv->temp_label = label_highflownext_temp_sensors;
+ priv->speed_label = label_highflownext_fan_speed;
+ priv->power_label = label_highflownext_power;
+ priv->voltage_label = label_highflownext_voltage;
+ break;
default:
break;
}
@@ -907,6 +991,7 @@ static const struct hid_device_id aqc_table[] = {
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK360) },
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_OCTO) },
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_QUADRO) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_HIGHFLOWNEXT) },
{ }
};
--
2.37.3