Re: [PATCH 2/4] pinctrl: qcom: spmi-gpio: Fix the GPIO strength mapping

[Krzysztof Kozlowski]

On 07/09/2022 22:15, Anjelique Melendez wrote:
> From: Anirudh Ghayal <quic_aghayal@xxxxxxxxxxx>
> 
> The SPMI based PMICs have the HIGH and LOW GPIO output
> strength mappings interchanged, fix them.
> 
> Keep the mapping same for older SSBI based PMICs.
> 
> CRs-Fixed: 2246473

What is this tag about?

> Signed-off-by: Anirudh Ghayal <quic_aghayal@xxxxxxxxxxx>
> Signed-off-by: Anjelique Melendez <quic_amelende@xxxxxxxxxxx>
> ---
>  drivers/pinctrl/qcom/pinctrl-spmi-gpio.c     | 2 +-
>  drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c     | 4 ++--
>  include/dt-bindings/pinctrl/qcom,pmic-gpio.h | 9 +++++++--
>  3 files changed, 10 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> index cf6b6047de8d..fceccf1ec099 100644
> --- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> @@ -525,7 +525,7 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
>  			pad->pullup = arg;
>  			break;
>  		case PMIC_GPIO_CONF_STRENGTH:
> -			if (arg > PMIC_GPIO_STRENGTH_LOW)
> +			if (arg > PMIC_GPIO_STRENGTH_HIGH)
>  				return -EINVAL;
>  			pad->strength = arg;
>  			break;
> diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
> index 1b41adda8129..0f96d130813b 100644
> --- a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
> +++ b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
> @@ -1,7 +1,7 @@
>  // SPDX-License-Identifier: GPL-2.0-only
>  /*
>   * Copyright (c) 2015, Sony Mobile Communications AB.
> - * Copyright (c) 2013, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2013, 2018 The Linux Foundation. All rights reserved.
>   */
>  
>  #include <linux/module.h>
> @@ -371,7 +371,7 @@ static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
>  			banks |= BIT(0);
>  			break;
>  		case PM8XXX_QCOM_DRIVE_STRENGH:
> -			if (arg > PMIC_GPIO_STRENGTH_LOW) {
> +			if (arg > PM8921_GPIO_STRENGTH_LOW) {
>  				dev_err(pctrl->dev, "invalid drive strength\n");
>  				return -EINVAL;
>  			}
> diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
> index e5df5ce45a0f..950be952ad3e 100644
> --- a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
> +++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h

You cannot mix bindings with driver. This is an ABI break.
> @@ -12,9 +12,14 @@
>  #define PMIC_GPIO_PULL_UP_1P5_30	3
>  
>  #define PMIC_GPIO_STRENGTH_NO		0
> -#define PMIC_GPIO_STRENGTH_HIGH		1
> +#define PMIC_GPIO_STRENGTH_LOW		1
>  #define PMIC_GPIO_STRENGTH_MED		2
> -#define PMIC_GPIO_STRENGTH_LOW		3
> +#define PMIC_GPIO_STRENGTH_HIGH		3

Didn't you just break all DTSes in the world?

Best regards,
Krzysztof