[PATCH V2 1/9] i2c: xiic: Add standard mode support for > 255 byte
From: Manikanta Guntupalli
Date: Thu Sep 22 2022 - 04:46:10 EST
From: Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>
Added standard mode for AXI I2C controller to enable read transfers
of size more than 255 bytes. The driver selects standard mode in the
following scenarios.
1. If a single message request comes from user space, requesting a
read of more than 255 bytes
2. If a message set request comes from user space consisting of many
messages and if any one of them is a read operation, irrespective
of the size of transfer. (This is done because it is observed that
repeated start operation is not happening in dynamic mode read as
expected in a message set request from user space.)
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@xxxxxxxxxx>
---
Changes for v2:
Merged the logic of xiic_std_fill_tx_fifo into xiic_fill_tx_fifo to remove
duplicate code.
Handled i2c msg->len == 0 case.
Squashed "Use 'nmsgs' variable instead of repeated_start" patch.
Squashed "Correct the BNB interrupt enable sequence" patch.
Squashed "remove unsupported flag I2C_M_NOSTART code" patch.
---
drivers/i2c/busses/i2c-xiic.c | 266 ++++++++++++++++++++++++++++------
1 file changed, 225 insertions(+), 41 deletions(-)
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index b3fe6b2aa3ca..2aa43e067fee 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -60,6 +60,7 @@ enum xiic_endian {
* @clk: Pointer to AXI4-lite input clock
* @state: See STATE_
* @singlemaster: Indicates bus is single master
+ * @dynamic: Mode of controller
*/
struct xiic_i2c {
struct device *dev;
@@ -76,6 +77,7 @@ struct xiic_i2c {
struct clk *clk;
enum xilinx_i2c_state state;
bool singlemaster;
+ bool dynamic;
};
#define XIIC_MSB_OFFSET 0
@@ -143,6 +145,9 @@ struct xiic_i2c {
#define XIIC_TX_DYN_START_MASK 0x0100 /* 1 = Set dynamic start */
#define XIIC_TX_DYN_STOP_MASK 0x0200 /* 1 = Set dynamic stop */
+/* Dynamic mode constants */
+#define MAX_READ_LENGTH_DYNAMIC 255 /* Max length for dynamic read */
+
/*
* The following constants define the register offsets for the Interrupt
* registers. There are some holes in the memory map for reserved addresses
@@ -316,13 +321,14 @@ static void xiic_deinit(struct xiic_i2c *i2c)
static void xiic_read_rx(struct xiic_i2c *i2c)
{
- u8 bytes_in_fifo;
+ u8 bytes_in_fifo, cr = 0, bytes_to_read = 0;
+ u32 bytes_rem = 0;
int i;
bytes_in_fifo = xiic_getreg8(i2c, XIIC_RFO_REG_OFFSET) + 1;
dev_dbg(i2c->adap.dev.parent,
- "%s entry, bytes in fifo: %d, msg: %d, SR: 0x%x, CR: 0x%x\n",
+ "%s entry, bytes in fifo: %d, rem: %d, SR: 0x%x, CR: 0x%x\n",
__func__, bytes_in_fifo, xiic_rx_space(i2c),
xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
@@ -330,13 +336,52 @@ static void xiic_read_rx(struct xiic_i2c *i2c)
if (bytes_in_fifo > xiic_rx_space(i2c))
bytes_in_fifo = xiic_rx_space(i2c);
- for (i = 0; i < bytes_in_fifo; i++)
+ bytes_to_read = bytes_in_fifo;
+
+ if (!i2c->dynamic) {
+ bytes_rem = xiic_rx_space(i2c) - bytes_in_fifo;
+
+ if (bytes_rem > IIC_RX_FIFO_DEPTH) {
+ bytes_to_read = bytes_in_fifo;
+ } else if (bytes_rem > 1) {
+ bytes_to_read = bytes_rem - 1;
+ } else if (bytes_rem == 1) {
+ bytes_to_read = 1;
+ /* Set NACK in CR to indicate slave transmitter */
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
+ XIIC_CR_NO_ACK_MASK);
+ } else if (bytes_rem == 0) {
+ bytes_to_read = bytes_in_fifo;
+
+ /* Generate stop on the bus if it is last message */
+ if (i2c->nmsgs == 1) {
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+ ~XIIC_CR_MSMS_MASK);
+ }
+
+ /* Make TXACK=0, clean up for next transaction */
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+ ~XIIC_CR_NO_ACK_MASK);
+ }
+ }
+
+ /* Read the fifo */
+ for (i = 0; i < bytes_to_read; i++) {
i2c->rx_msg->buf[i2c->rx_pos++] =
xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
+ }
- xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET,
- (xiic_rx_space(i2c) > IIC_RX_FIFO_DEPTH) ?
- IIC_RX_FIFO_DEPTH - 1 : xiic_rx_space(i2c) - 1);
+ if (i2c->dynamic) {
+ u8 bytes;
+
+ /* Receive remaining bytes if less than fifo depth */
+ bytes = min_t(u8, xiic_rx_space(i2c), IIC_RX_FIFO_DEPTH);
+ bytes--;
+ xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
+ }
}
static int xiic_tx_fifo_space(struct xiic_i2c *i2c)
@@ -360,7 +405,15 @@ static void xiic_fill_tx_fifo(struct xiic_i2c *i2c)
if (!xiic_tx_space(i2c) && i2c->nmsgs == 1) {
/* last message in transfer -> STOP */
- data |= XIIC_TX_DYN_STOP_MASK;
+ if (i2c->dynamic) {
+ data |= XIIC_TX_DYN_STOP_MASK;
+ } else {
+ u8 cr;
+ /* Write to CR to stop */
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
+ ~XIIC_CR_MSMS_MASK);
+ }
dev_dbg(i2c->adap.dev.parent, "%s TX STOP\n", __func__);
}
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
@@ -401,7 +454,9 @@ static irqreturn_t xiic_process(int irq, void *dev_id)
dev_dbg(i2c->adap.dev.parent, "%s: SR: 0x%x, msg: %p, nmsgs: %d\n",
__func__, xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
i2c->tx_msg, i2c->nmsgs);
-
+ dev_dbg(i2c->adap.dev.parent, "%s, ISR: 0x%x, CR: 0x%x\n",
+ __func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+ xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
/* Service requesting interrupt */
if ((pend & XIIC_INTR_ARB_LOST_MASK) ||
@@ -579,31 +634,101 @@ static int xiic_busy(struct xiic_i2c *i2c)
static void xiic_start_recv(struct xiic_i2c *i2c)
{
u16 rx_watermark;
+ u8 cr = 0, rfd_set = 0;
struct i2c_msg *msg = i2c->rx_msg = i2c->tx_msg;
+ unsigned long flags;
- /* Clear and enable Rx full interrupt. */
- xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK | XIIC_INTR_TX_ERROR_MASK);
+ dev_dbg(i2c->adap.dev.parent, "%s entry, ISR: 0x%x, CR: 0x%x\n",
+ __func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+ xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
- /* we want to get all but last byte, because the TX_ERROR IRQ is used
- * to inidicate error ACK on the address, and negative ack on the last
- * received byte, so to not mix them receive all but last.
- * In the case where there is only one byte to receive
- * we can check if ERROR and RX full is set at the same time
- */
- rx_watermark = msg->len;
- if (rx_watermark > IIC_RX_FIFO_DEPTH)
- rx_watermark = IIC_RX_FIFO_DEPTH;
- xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, (u8)(rx_watermark - 1));
+ /* Disable Tx interrupts */
+ xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK | XIIC_INTR_TX_EMPTY_MASK);
+
+ if (i2c->dynamic) {
+ u8 bytes;
+ u16 val;
+
+ /* Clear and enable Rx full interrupt. */
+ xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
+ XIIC_INTR_TX_ERROR_MASK);
+
+ /*
+ * We want to get all but last byte, because the TX_ERROR IRQ
+ * is used to indicate error ACK on the address, and
+ * negative ack on the last received byte, so to not mix
+ * them receive all but last.
+ * In the case where there is only one byte to receive
+ * we can check if ERROR and RX full is set at the same time
+ */
+ rx_watermark = msg->len;
+ bytes = min_t(u8, rx_watermark, IIC_RX_FIFO_DEPTH);
+
+ if (rx_watermark > 0)
+ bytes--;
+ xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
+
+ local_irq_save(flags);
- if (!(msg->flags & I2C_M_NOSTART))
/* write the address */
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
- i2c_8bit_addr_from_msg(msg) | XIIC_TX_DYN_START_MASK);
+ i2c_8bit_addr_from_msg(msg) |
+ XIIC_TX_DYN_START_MASK);
+
+ /* If last message, include dynamic stop bit with length */
+ val = (i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0;
+ val |= msg->len;
+
+ xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, val);
+
+ xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+
+ local_irq_restore(flags);
+ } else {
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+
+ /* Set Receive fifo depth */
+ rx_watermark = msg->len;
+ if (rx_watermark > IIC_RX_FIFO_DEPTH) {
+ rfd_set = IIC_RX_FIFO_DEPTH - 1;
+ } else if (rx_watermark == 1) {
+ rfd_set = rx_watermark - 1;
+ /* Handle single byte transfer separately */
+ cr |= XIIC_CR_NO_ACK_MASK;
+ } else if (rx_watermark == 0) {
+ rfd_set = rx_watermark;
+ cr |= XIIC_CR_NO_ACK_MASK;
+ } else {
+ rfd_set = rx_watermark - 2;
+ }
+ /* Check if RSTA should be set */
+ if (cr & XIIC_CR_MSMS_MASK) {
+ /* Already a master, RSTA should be set */
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+ XIIC_CR_REPEATED_START_MASK) &
+ ~(XIIC_CR_DIR_IS_TX_MASK));
+ }
- xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+ xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rfd_set);
- xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
- msg->len | ((i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0));
+ /* Clear and enable Rx full and transmit complete interrupts */
+ xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
+ XIIC_INTR_TX_ERROR_MASK);
+
+ /* Write the address */
+ xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
+ i2c_8bit_addr_from_msg(msg));
+
+ /* Write to Control Register,to start transaction in Rx mode */
+ if ((cr & XIIC_CR_MSMS_MASK) == 0) {
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+ XIIC_CR_MSMS_MASK)
+ & ~(XIIC_CR_DIR_IS_TX_MASK));
+ }
+ dev_dbg(i2c->adap.dev.parent, "%s end, ISR: 0x%x, CR: 0x%x\n",
+ __func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
+ xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
+ }
if (i2c->nmsgs == 1)
/* very last, enable bus not busy as well */
@@ -611,10 +736,15 @@ static void xiic_start_recv(struct xiic_i2c *i2c)
/* the message is tx:ed */
i2c->tx_pos = msg->len;
+
+ /* Enable interrupts */
+ xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK);
}
static void xiic_start_send(struct xiic_i2c *i2c)
{
+ u8 cr = 0;
+ u16 data;
struct i2c_msg *msg = i2c->tx_msg;
dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, len: %d",
@@ -623,24 +753,56 @@ static void xiic_start_send(struct xiic_i2c *i2c)
__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
- if (!(msg->flags & I2C_M_NOSTART)) {
+ if (i2c->dynamic) {
/* write the address */
- u16 data = i2c_8bit_addr_from_msg(msg) |
- XIIC_TX_DYN_START_MASK;
- if ((i2c->nmsgs == 1) && msg->len == 0)
+ data = i2c_8bit_addr_from_msg(msg) |
+ XIIC_TX_DYN_START_MASK;
+
+ if (i2c->nmsgs == 1 && msg->len == 0)
/* no data and last message -> add STOP */
data |= XIIC_TX_DYN_STOP_MASK;
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
- }
- /* Clear any pending Tx empty, Tx Error and then enable them. */
- xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_ERROR_MASK |
- XIIC_INTR_BNB_MASK |
- ((i2c->nmsgs > 1 || xiic_tx_space(i2c)) ?
- XIIC_INTR_TX_HALF_MASK : 0));
+ /* Clear any pending Tx empty, Tx Error and then enable them */
+ xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
+ XIIC_INTR_TX_ERROR_MASK |
+ XIIC_INTR_BNB_MASK |
+ ((i2c->nmsgs > 1 || xiic_tx_space(i2c)) ?
+ XIIC_INTR_TX_HALF_MASK : 0));
+
+ xiic_fill_tx_fifo(i2c);
+ } else {
+ /* Check if RSTA should be set */
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ if (cr & XIIC_CR_MSMS_MASK) {
+ /* Already a master, RSTA should be set */
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
+ XIIC_CR_REPEATED_START_MASK |
+ XIIC_CR_DIR_IS_TX_MASK) &
+ ~(XIIC_CR_NO_ACK_MASK));
+ }
+
+ /* Write address to FIFO */
+ data = i2c_8bit_addr_from_msg(msg);
+ xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
- xiic_fill_tx_fifo(i2c);
+ /* Fill fifo */
+ xiic_fill_tx_fifo(i2c);
+
+ if ((cr & XIIC_CR_MSMS_MASK) == 0) {
+ /* Start Tx by writing to CR */
+ cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
+ xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
+ XIIC_CR_MSMS_MASK |
+ XIIC_CR_DIR_IS_TX_MASK);
+ }
+
+ /* Clear any pending Tx empty, Tx Error and then enable them */
+ xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
+ XIIC_INTR_TX_ERROR_MASK |
+ XIIC_INTR_BNB_MASK);
+ }
}
static void __xiic_start_xfer(struct xiic_i2c *i2c)
@@ -701,6 +863,33 @@ static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
if (err < 0)
return err;
+ /* Decide standard mode or Dynamic mode */
+ i2c->dynamic = true;
+
+ /*
+ * If number of messages is 1 and read length is > 255 bytes,
+ * enter standard mode
+ */
+
+ if (i2c->nmsgs == 1 && (i2c->tx_msg->flags & I2C_M_RD) &&
+ i2c->tx_msg->len > MAX_READ_LENGTH_DYNAMIC) {
+ i2c->dynamic = false;
+ } else if (i2c->nmsgs > 1) {
+ int count;
+
+ /*
+ * If number of messages is more than 1 and one of them is
+ * a read message, enter standard mode. Since repeated start
+ * operation in dynamic mode read is not happenning
+ */
+ for (count = 0; count < i2c->nmsgs; count++) {
+ if (i2c->tx_msg[count].flags & I2C_M_RD) {
+ i2c->dynamic = false;
+ break;
+ }
+ }
+ }
+
err = xiic_start_xfer(i2c, msgs, num);
if (err < 0) {
dev_err(adap->dev.parent, "Error xiic_start_xfer\n");
@@ -737,15 +926,10 @@ static const struct i2c_algorithm xiic_algorithm = {
.functionality = xiic_func,
};
-static const struct i2c_adapter_quirks xiic_quirks = {
- .max_read_len = 255,
-};
-
static const struct i2c_adapter xiic_adapter = {
.owner = THIS_MODULE,
.class = I2C_CLASS_DEPRECATED,
.algo = &xiic_algorithm,
- .quirks = &xiic_quirks,
};
static int xiic_i2c_probe(struct platform_device *pdev)
--
2.25.1