Re: [PATCH v2] dt-bindings: net: marvell,pp2: convert to json-schema

[Krzysztof Kozlowski]

On 27/09/2022 01:21, Michał Grzelak wrote:
> This converts the marvell,pp2 bindings from text to proper schema.
> 
> Move 'marvell,system-controller' and 'dma-coherent' properties from
> port up to the controller node, to match what is actually done in DT.
> 
> Signed-off-by: Michał Grzelak <mig@xxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/net/marvell,pp2.yaml  | 241 ++++++++++++++++++
>  .../devicetree/bindings/net/marvell-pp2.txt   | 141 ----------

Thank you for your patch. There is something to discuss/improve.


> +properties:
> +  compatible:
> +    enum:
> +      - marvell,armada-375-pp2
> +      - marvell,armada-7k-pp22
> +
> +  reg:
> +    minItems: 3
> +    maxItems: 4
> +    description: |
> +      For "marvell,armada-375-pp2", must contain the following register sets:
> +        - common controller registers
> +        - LMS registers
> +        - one register area per Ethernet port
> +      For "marvell,armada-7k-pp22" used by 7K/8K and CN913X, must contain the following register sets:
> +        - packet processor registers
> +        - networking interfaces registers
> +        - CM3 address space used for TX Flow Control

Instead of this description, in define them for each variant in
allOf:if:then (just like for clocks below)

> +
> +  clocks:
> +    minItems: 2
> +    items:
> +      - description: main controller clock
> +      - description: GOP clock
> +      - description: MG clock
> +      - description: MG Core clock
> +      - description: AXI clock

This needs to be restricted per variant - minItems and maxItems in
allOf:if:then.

> +
> +  clock-names:
> +    minItems: 2
> +    items:
> +      - const: pp_clk
> +      - const: gop_clk
> +      - const: mg_clk
> +      - const: mg_core_clk
> +      - const: axi_clk

The same.

> +
> +  dma-coherent: true
> +  '#size-cells': true
> +  '#address-cells': true

You need const:X for both cells (unless they come from some other schema
but then you would not need to list them here).

> +
> +  marvell,system-controller:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: a phandle to the system controller.
> +
> +patternProperties:
> +  '^eth[0-9a-f]*(@.*)?$':

The name should be "(ethernet-)?port", unless anything depends on
particular naming?

> +    type: object

You need description here.

> +    properties:
> +      interrupts:
> +        minItems: 1
> +        maxItems: 10
> +        description: interrupt(s) for the port
> +
> +      interrupt-names:
> +        items:

minItems: 1

> +          - const: hif0
> +          - const: hif1
> +          - const: hif2
> +          - const: hif3
> +          - const: hif4
> +          - const: hif5
> +          - const: hif6
> +          - const: hif7
> +          - const: hif8
> +          - const: link
> +
> +        description: >
> +          if more than a single interrupt for is given, must be the
> +          name associated to the interrupts listed. Valid names are:
> +          "hifX", with X in [0..8], and "link". The names "tx-cpu0",
> +          "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported
> +          for backward compatibility but shouldn't be used for new
> +          additions.
> +
> +      port-id:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        description: ID of the port from the MAC point of view.
> +
> +      phy:
> +        $ref: /schemas/types.yaml#/definitions/phandle
> +        description: >
> +          a phandle to a phy node defining the PHY address
> +          (as the reg property, a single integer).
> +
> +      phy-mode:
> +        $ref: "ethernet-controller.yaml#/properties/phy-mode"

You can skip quotes.

> +
> +      marvell,loopback:
> +        $ref: /schemas/types.yaml#/definitions/flag
> +        description: port is loopback mode.
> +
> +      gop-port-id:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        description: >
> +          only for marvell,armada-7k-pp22, ID of the port from the
> +          GOP (Group Of Ports) point of view. This ID is used to index the
> +          per-port registers in the second register area.
> +
> +    required:
> +      - interrupts
> +      - port-id
> +      - phy-mode
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +
> +allOf:
> +  - $ref: ethernet-controller.yaml#
> +  - if:
> +      properties:
> +        compatible:
> +          const: marvell,armada-7k-pp22
> +    then:
> +      patternProperties:
> +        '^eth[0-9a-f]*(@.*)?$':
> +          required:
> +            - gop-port-id

else:
  patternProperties:
     ....
       gop-port-id: false

> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |

Best regards,
Krzysztof