Re: [PATCH 2/3] arm64: dts: qcom: sdm845-db845c: correct SPI2 pins drive strength

[Krzysztof Kozlowski]

On 30/09/2022 22:12, Doug Anderson wrote:
> Hi,
> 
> On Fri, Sep 30, 2022 at 11:22 AM Krzysztof Kozlowski
> <krzysztof.kozlowski@xxxxxxxxxx> wrote:
>>
>> The pin configuration (done with generic pin controller helpers and
>> as expressed by bindings) requires children nodes with either:
>> 1. "pins" property and the actual configuration,
>> 2. another set of nodes with above point.
>>
>> The qup_spi2_default pin configuration used second method - with a
>> "pinmux" child.
>>
>> Fixes: 8d23a0040475 ("arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes")
>> Cc: <stable@xxxxxxxxxxxxxxx>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
>>
>> ---
>>
>> Not tested on hardware.
>> ---
>>  arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 +++-
>>  1 file changed, 3 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
>> index 132417e2d11e..a157eab66dee 100644
>> --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
>> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
>> @@ -1123,7 +1123,9 @@ &wifi {
>>
>>  /* PINCTRL - additions to nodes defined in sdm845.dtsi */
>>  &qup_spi2_default {
>> -       drive-strength = <16>;
>> +       pinmux {
>> +               drive-strength = <16>;
>> +       };
> 
> The convention on Qualcomm boards of this era is that muxing (setting
> the function) is done under a "pinmux" node and, unless some of the
> pins need to be treated differently like for the UARTs, configuration
> (bias, drive strength, etc) is done under a "pinconf" subnode.

Yes, although this was not expressed in bindings.

> I
> believe that the "pinconf" subnode also needs to replicate the list of
> pins, or at least that's what we did everywhere else on sdm845 /
> sc7180.

Yes.

> 
> Thus to match conventions, I assume you'd do:
> 
> &qup_spi2_default {
>   pinconf {

No, because I want a convention of all pinctrl bindings and drivers, not
convention of old pinctrl ones. The new ones are already moved or being
moved to "-state" and "-pins". In the same time I am also unifying the
requirement of "function" property - enforcing it in each node, thus
"pinconf" will not be valid anymore.

>     pins = "gpio27", "gpio28", "gpio29", "gpio30";
>     drive-strength = <16>;
>   };
> };
> 
> We've since moved away from this to a less cumbersome approach, but
> for "older" boards like db845c we should probably match the existing
> convention, or have a flag day and change all sdm845 boards over to
> the new convention.

That's what my next patchset from yesterday was doing. Unifying the
bindings with modern bindings and converting DTS to match them.

https://lore.kernel.org/linux-devicetree/20220930200529.331223-1-krzysztof.kozlowski@xxxxxxxxxx/T/#t


Best regards,
Krzysztof