Re: [PATCH 3/3] arch: arm64: ti: Add support for AM68 SK base board

From: Krzysztof Kozlowski
Date: Tue Oct 18 2022 - 09:03:25 EST

Next message: Krzysztof Kozlowski: "Re: [PATCH] dt-bindings: PCI: qcom-ep: Fix PERST register description"
Previous message: Jianmin Lv: "Re: [PATCH V5 1/2] ACPI / scan: Support multiple dma windows with different offsets"
In reply to: Sinthu Raja: "[PATCH 3/3] arch: arm64: ti: Add support for AM68 SK base board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 18/10/2022 08:38, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@xxxxxx>
>
> The SK architecture comprises of baseboard and a SOM board. It is
> as follows,
>
> +--------------------------------------+---+
> | | |<--Connectors
> | +---|
> | +---------------------------+ | |
> | | SOM | +---|
> | | | | |
> | | | +---| Power Supply
> | | | | |
> | +---------------------------+ | |
> | |<--+
> | BASE BOARD |
> +------------------------------------------+

This is pretty straightforward for SoM, I am not sure what's the benefit
to add it.

>
> AM68 Starter Kit's baseboard contains most of the actual connectors,
> power supply etc. The System on Module (SoM) is plugged on to the base
> board. Therefore, add support for peripherals brought out in the base
> board.
>
> Schematics: https://www.ti.com/lit/zip/SPRR463
>
> Signed-off-by: Sinthu Raja <sinthu.raja@xxxxxx>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> .../boot/dts/ti/k3-am68-sk-base-board.dts | 459 ++++++++++++++++++
> 2 files changed, 461 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 4555a5be2257..498b089d96f8 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
>
> +dtb-$(CONFIG_ARCH_K3) += k3-am68-sk-base-board.dtb
> +

Alphabetical order, although does not look like other entries are ordered...

> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> new file mode 100644
> index 000000000000..f51cbd2e3b72
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> @@ -0,0 +1,459 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + *
> + * Base Board: https://www.ti.com/lit/zip/SPRR463
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-am68-sk-som.dtsi"
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include <dt-bindings/phy/phy-cadence.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/mux/ti-serdes.h>
> +
> +/ {
> + compatible = "ti,am68-sk", "ti,j721s2";
> + model = "Texas Instruments AM68 SK";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x2880000";

None of these bootargs are suitable for mainline. earlycon for sure - it
is pure debug option.

> + };
> +
> + aliases {
> + serial2 = &main_uart8;
> + mmc1 = &main_sdhci1;
> + can0 = &mcu_mcan0;
> + can1 = &mcu_mcan1;
> + can2 = &main_mcan6;
> + can3 = &main_mcan7;
> + };
> +
> + vusb_main: fixedregulator-vusb-main5v0 {

Not "fixedregulator-" but just "regulator-"

Same in other places.

> + /* USB MAIN INPUT 5V DC */
> + compatible = "regulator-fixed";
> + regulator-name = "vusb-main5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_3v3: fixedregulator-vsys3v3 {
> + /* Output of LM5141 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vusb_main>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: fixedregulator-sd {
> + /* Output of TPS22918 */
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vsys_3v3>;
> + gpio = <&exp1 10 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv: gpio-regulator-TLV71033 {

1. regulator-xxxxxx
2. lowercase node name

> + /* Output of TLV71033 */
> + compatible = "regulator-gpio";
> + regulator-name = "tlv71033";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_3v3>;
> + gpios = <&main_gpio0 49 GPIO_ACTIVE_HIGH>;> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> +
> + vsys_io_1v8: regulator-vsys-io-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_io_1v2: regulator-vsys-io-1v2 {
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_io_1v2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + transceiver1: can-phy0 {
> + compatible = "ti,tcan1042";
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_mcan0_pins_default>;
> + standby-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
> + };
> +
> + transceiver2: can-phy1 {
> + compatible = "ti,tcan1042";
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_mcan1_pins_default>;
> + standby-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
> + };
> +
> + transceiver3: can-phy2 {
> + compatible = "ti,tcan1042";
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mcan6_pins_default>;
> + standby-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
> + };
> +
> + transceiver4: can-phy3 {
> + compatible = "ti,tcan1042";
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mcan7_pins_default>;
> + standby-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&main_pmx0 {
> +

No need for blank line.

> + main_uart8_pins_default: main-uart8-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
> + J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
> + >;
> + };
> +
> + main_i2c0_pins_default: i2c0_pins_default {

No underscores in node names. Why do you use here different style than
in other places?

> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0e0, PIN_INPUT, 0) /* (AH25) I2C0_SCL */
> + J721S2_IOPAD(0x0e4, PIN_INPUT, 0) /* (AE24) I2C0_SDA */
> + >;
> + };
> +
> + main_mmc1_pins_default: main-mmc1-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
> + J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */
> + J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */
> + J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
> + J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
> + J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
> + J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
> + >;
> + };
> +
> + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0c4, PIN_INPUT, 7) /* (AB26) ECAP0_IN_APWM_OUT.GPIO0_49 */
> + >;
> + };
> +
> + main_usbss0_pins_default: main-usbss0-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
> + >;
> + };
> +
> + main_mcan6_pins_default: mcan6_pins_default {

Be sure you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x098, PIN_INPUT, 0) /* (V25) MCASP0_AXR10.MCAN6_RX */
> + J721S2_IOPAD(0x094, PIN_INPUT, 0) /* (AA25) MCASP0_AXR9.MCAN6_TX */
> + >;
> + };
> +
> + main_mcan7_pins_default: mcan7_pins_default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */
> + J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
> + >;
> + };
> +
> +};
> +
> +&wkup_pmx0 {
> + mcu_cpsw_pins_default: mcu-cpsw-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
> + J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
> + J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
> + J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
> + J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
> + J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
> + J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
> + J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
> + J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
> + J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
> + J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
> + J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
> + >;
> + };
> +
> + mcu_mdio_pins_default: mcu-mdio-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
> + J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
> + >;
> + };
> +
> + mcu_mcan0_pins_default: mcu-mcan0-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
> + J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
> + >;
> + };
> +
> + mcu_mcan1_pins_default: mcu-mcan1-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
> + J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
> + >;
> + };
> +
> + mcu_i2c1_pins_default: mcu_i2c1_pins_default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
> + J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
> + >;
> + };
> +

Drop line

> +};
> +
> +&main_gpio2 {
> + status = "disabled";
> +};
> +
Best regards,
Krzysztof

Next message: Krzysztof Kozlowski: "Re: [PATCH] dt-bindings: PCI: qcom-ep: Fix PERST register description"
Previous message: Jianmin Lv: "Re: [PATCH V5 1/2] ACPI / scan: Support multiple dma windows with different offsets"
In reply to: Sinthu Raja: "[PATCH 3/3] arch: arm64: ti: Add support for AM68 SK base board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]