Re: [PATCH v2 2/3] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs

From: Melody Olvera
Date: Mon Oct 24 2022 - 20:32:41 EST




On 10/24/2022 3:51 PM, Richard Acayan wrote:
>> On 10/24/2022 3:28 PM, Richard Acayan wrote:
>>>> On 10/23/2022 5:53 PM, Richard Acayan wrote:
>>>>>> Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
>>>>>> descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and interrupt-controller
>>>>>> to boot to shell with console on these SoCs.
>>>>>>
>>>>>> Signed-off-by: Melody Olvera <quic_molvera@xxxxxxxxxxx>
>>>>>> ---
>>>>>> arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1646 +++++++++++++++++++++++++
>>>>>> arch/arm64/boot/dts/qcom/qru1000.dtsi | 27 +
>>>>>> 2 files changed, 1673 insertions(+)
>>>>>> create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
>>>>>> create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
>>>>>>
>>>>>> diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
>>>>>> new file mode 100644
>>>>>> index 000000000000..777734b30f56
>>>>>> --- /dev/null
>>>>>> +++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
>>>>>> @@ -0,0 +1,1646 @@
>>>>>> +// SPDX-License-Identifier: BSD-3-Clause
>>>>>> +/*
>>>>>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
>>>>>> + */
>>>>>> +
>>>>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>>> +#include <dt-bindings/clock/qcom,gcc-qdu1000.h>
>>>>>> +#include <dt-bindings/clock/qcom,rpmh.h>
>>>>>> +#include <dt-bindings/dma/qcom-gpi.h>
>>>>>> +#include <dt-bindings/interconnect/qcom,qdu1000.h>
>>>>>> +#include <dt-bindings/power/qcom-rpmpd.h>
>>>>>> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>>>>> +
>>>>>> +/ {
>>>>>> + interrupt-parent = <&intc>;
>>>>>> +
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <2>;
>>>>>> +
>>>>>> + chosen: chosen { };
>>>>>> +
>>>>>> + clocks {
>>>>>> + xo_board: xo-board {
>>>>>> + compatible = "fixed-clock";
>>>>>> + clock-frequency = <19200000>;
>>>>>> + clock-output-names = "xo_board";
>>>>>> + #clock-cells = <0>;
>>>>>> + };
>>>>>> +
>>>>>> + sleep_clk: sleep-clk {
>>>>>> + compatible = "fixed-clock";
>>>>>> + clock-frequency = <32000>;
>>>>>> + #clock-cells = <0>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + cpus {
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <0>;
>>>>>> +
>>>>>> + CPU0: cpu@0 {
>>>>>> + device_type = "cpu";
>>>>>> + compatible = "arm,cortex-a55";
>>>>>> + reg = <0x0 0x0>;
>>>>>> + enable-method = "psci";
>>>>>> + power-domain-names = "psci";
>>>>>> + power-domains = <&CPU_PD0>;
>>>>>> + qcom,freq-domains = <&cpufreq_hw 0>;
>>>>>> + next-level-cache = <&L2_0>;
>>>>>> + L2_0: l2-cache {
>>>>>> + compatible = "cache";
>>>>>> + next-level-cache = <&L3_0>;
>>>>>> + L3_0: l3-cache {
>>>>>> + compatible = "cache";
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + CPU1: cpu@100 {
>>>>>> + device_type = "cpu";
>>>>>> + compatible = "arm,cortex-a55";
>>>>>> + reg = <0x0 0x100>;
>>>>>> + enable-method = "psci";
>>>>>> + power-domains = <&CPU_PD1>;
>>>>>> + power-domain-names = "psci";
>>>>>> + qcom,freq-domains = <&cpufreq_hw 0>;
>>>>>> + next-level-cache = <&L2_100>;
>>>>>> + L2_100: l2-cache {
>>>>>> + compatible = "cache";
>>>>>> + next-level-cache = <&L3_0>;
>>>>>> + };
>>>>>> +
>>>>>> + };
>>>>>> +
>>>>>> + CPU2: cpu@200 {
>>>>>> + device_type = "cpu";
>>>>>> + compatible = "arm,cortex-a55";
>>>>>> + reg = <0x0 0x200>;
>>>>>> + enable-method = "psci";
>>>>>> + power-domains = <&CPU_PD2>;
>>>>>> + power-domain-names = "psci";
>>>>>> + qcom,freq-domains = <&cpufreq_hw 0>;
>>>>>> + next-level-cache = <&L2_200>;
>>>>>> + L2_200: l2-cache {
>>>>>> + compatible = "cache";
>>>>>> + next-level-cache = <&L3_0>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + CPU3: cpu@300 {
>>>>>> + device_type = "cpu";
>>>>>> + compatible = "arm,cortex-a55";
>>>>>> + reg = <0x0 0x300>;
>>>>>> + enable-method = "psci";
>>>>>> + power-domains = <&CPU_PD3>;
>>>>>> + power-domain-names = "psci";
>>>>>> + qcom,freq-domains = <&cpufreq_hw 0>;
>>>>>> + next-level-cache = <&L2_300>;
>>>>>> + L2_300: l2-cache {
>>>>>> + compatible = "cache";
>>>>>> + next-level-cache = <&L3_0>;
>>>>>> + };
>>>>>> +
>>>>>> + };
>>>>>> +
>>>>>> + cpu-map {
>>>>>> + cluster0 {
>>>>>> + core0 {
>>>>>> + cpu = <&CPU0>;
>>>>>> + };
>>>>>> +
>>>>>> + core1 {
>>>>>> + cpu = <&CPU1>;
>>>>>> + };
>>>>>> +
>>>>>> + core2 {
>>>>>> + cpu = <&CPU2>;
>>>>>> + };
>>>>>> +
>>>>>> + core3 {
>>>>>> + cpu = <&CPU3>;
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + idle-states {
>>>>>> + entry-method = "psci";
>>>>>> +
>>>>>> + CPU_OFF: cpu-sleep-0 {
>>>>>> + compatible = "arm,idle-state";
>>>>>> + idle-state-name = "rail-pc";
>>>>>> + entry-latency-us = <274>;
>>>>>> + exit-latency-us = <480>;
>>>>>> + min-residency-us = <3934>;
>>>>>> + arm,psci-suspend-param = <0x40000004>;
>>>>>> + local-timer-stop;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + domain-idle-states {
>>>>>> + CLUSTER_SLEEP_0: cluster-sleep-0 {
>>>>>> + compatible = "domain-idle-state";
>>>>>> + idle-state-name = "cluster-l3-off";
>>>>>> + entry-latency-us = <584>;
>>>>>> + exit-latency-us = <2332>;
>>>>>> + min-residency-us = <6118>;
>>>>>> + arm,psci-suspend-param = <0x41000044>;
>>>>>> + };
>>>>>> +
>>>>>> + CLUSTER_SLEEP_1: cluster-sleep-1 {
>>>>>> + compatible = "domain-idle-state";
>>>>>> + idle-state-name = "cluster-power-collapse";
>>>>>> + entry-latency-us = <2893>;
>>>>>> + exit-latency-us = <4023>;
>>>>>> + min-residency-us = <9987>;
>>>>>> + arm,psci-suspend-param = <0x41003344>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + firmware {
>>>>>> + qcom_scm {
>>>>>> + compatible = "qcom,scm-qdu100", "qcom.scm-qru1000", "qcom,scm";
>>>>>> + #reset-cells = <1>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + clk_virt: interconnect-0 {
>>>>>> + compatible = "qcom,qdu1000-clk-virt", "qcom,qru1000-clk-virt";
>>>>>> + #interconnect-cells = <2>;
>>>>>> + qcom,bcm-voters = <&apps_bcm_voter>;
>>>>>> + };
>>>>>> +
>>>>>> + mc_virt: interconnect-1 {
>>>>>> + compatible = "qcom,qdu1000-mc-virt", "qcom,qru1000-mc-virt";
>>>>>> + #interconnect-cells = <2>;
>>>>>> + qcom,bcm-voters = <&apps_bcm_voter>;
>>>>>> + };
>>>>>> +
>>>>>> + memory@80000000 {
>>>>>> + device_type = "memory";
>>>>>> + /* We expect the bootloader to fill in the size */
>>>>>> + reg = <0x0 0x80000000 0x0 0x0>;
>>>>>> + };
>>>>>> +
>>>>>> + pmu {
>>>>>> + compatible = "arm,armv8-pmuv3";
>>>>>> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + };
>>>>>> +
>>>>>> + psci {
>>>>>> + compatible = "arm,psci-1.0";
>>>>>> + method = "smc";
>>>>>> +
>>>>>> + CPU_PD0: cpu-pd0 {
>>>>>> + #power-domain-cells = <0>;
>>>>>> + power-domains = <&CLUSTER_PD>;
>>>>>> + domain-idle-states = <&CPU_OFF>;
>>>>>> + };
>>>>>> +
>>>>>> + CPU_PD1: cpu-pd1 {
>>>>>> + #power-domain-cells = <0>;
>>>>>> + power-domains = <&CLUSTER_PD>;
>>>>>> + domain-idle-states = <&CPU_OFF>;
>>>>>> + };
>>>>>> +
>>>>>> + CPU_PD2: cpu-pd2 {
>>>>>> + #power-domain-cells = <0>;
>>>>>> + power-domains = <&CLUSTER_PD>;
>>>>>> + domain-idle-states = <&CPU_OFF>;
>>>>>> + };
>>>>>> +
>>>>>> + CPU_PD3: cpu-pd3 {
>>>>>> + #power-domain-cells = <0>;
>>>>>> + power-domains = <&CLUSTER_PD>;
>>>>>> + domain-idle-states = <&CPU_OFF>;
>>>>>> + };
>>>>>> +
>>>>>> + CLUSTER_PD: cluster-pd {
>>>>>> + #power-domain-cells = <0>;
>>>>>> + domain-idle-states = <&CLUSTER_SLEEP_0 &CLUSTER_SLEEP_1>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + reserved_memory: reserved-memory {
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <2>;
>>>>>> + ranges;
>>>>>> +
>>>>>> + hyp_mem: memory@80000000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80000000 0x0 0x600000>;
>>>>>> + };
>>>>>> +
>>>>>> + xbl_dt_log_mem: memory@80600000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80600000 0x0 0x40000>;
>>>>>> + };
>>>>>> +
>>>>>> + xbl_ramdump_mem: memory@80640000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80640000 0x0 0x1c0000>;
>>>>>> + };
>>>>>> +
>>>>>> + aop_image_mem: memory@80800000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80800000 0x0 0x60000>;
>>>>>> + };
>>>>>> +
>>>>>> + aop_cmd_db_mem: memory@80860000 {
>>>>>> + compatible = "qcom,cmd-db";
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80860000 0x0 0x20000>;
>>>>>> + };
>>>>>> +
>>>>>> + aop_config_mem: memory@80880000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80880000 0x0 0x20000>;
>>>>>> + };
>>>>>> +
>>>>>> + tme_crash_dump_mem: memory@808a0000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x808a0000 0x0 0x40000>;
>>>>>> + };
>>>>>> +
>>>>>> + tme_log_mem: memory@808e0000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x808e0000 0x0 0x4000>;
>>>>>> + };
>>>>>> +
>>>>>> + uefi_log_mem: memory@808e4000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x808e4000 0x0 0x10000>;
>>>>>> + };
>>>>>> +
>>>>>> + /* secdata region can be reused by apps */
>>>>>> +
>>>>>> + smem_mem: memory@80900000 {
>>>>>> + compatible = "qcom,smem";
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80900000 0x0 0x200000>;
>>>>>> + hwlocks = <&tcsr_mutex 3>;
>>>>>> + };
>>>>>> +
>>>>>> + cpucp_fw_mem: memory@80b00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80b00000 0x0 0x100000>;
>>>>>> + };
>>>>>> +
>>>>>> + xbl_sc_mem: memory@80c00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x80c00000 0x0 0x40000>;
>>>>>> + };
>>>>>> +
>>>>>> + /* uefi region can be reused by apps */
>>>>>> +
>>>>>> + tz_stat_mem: memory@81d00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x81d00000 0x0 0x100000>;
>>>>>> + };
>>>>>> +
>>>>>> + tags_mem: memory@81e00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x81e00000 0x0 0x500000>;
>>>>>> + };
>>>>>> +
>>>>>> + qtee_mem: memory@82300000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x82300000 0x0 0x500000>;
>>>>>> + };
>>>>>> +
>>>>>> + ta_mem: memory@82800000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x82800000 0x0 0xa00000>;
>>>>>> + };
>>>>>> +
>>>>>> + fs1_mem: memory@83200000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x83200000 0x0 0x400000>;
>>>>>> + };
>>>>>> +
>>>>>> + fs2_mem: memory@83600000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x83600000 0x0 0x400000>;
>>>>>> + };
>>>>>> +
>>>>>> + fs3_mem: memory@83a00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x83a00000 0x0 0x400000>;
>>>>>> + };
>>>>>> +
>>>>>> + /* Linux kernel image is loaded at 0x83e00000 */
>>>>>> +
>>>>>> + ipa_fw_mem: memory@8be00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x8be00000 0x0 0x10000>;
>>>>>> + };
>>>>>> +
>>>>>> + ipa_gsi_mem: memory@8be10000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x8be10000 0x0 0x14000>;
>>>>>> + };
>>>>>> +
>>>>>> + mpss_mem: memory@8c000000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x8c000000 0x0 0x12c00000>;
>>>>>> + };
>>>>>> +
>>>>>> + q6_mpss_dtb_mem: memory@9ec00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0x9ec00000 0x0 0x80000>;
>>>>>> + };
>>>>>> +
>>>>>> + tenx_mem: memory@a0000000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xa0000000 0x0 0x19600000>;
>>>>>> + };
>>>>>> +
>>>>>> + oem_tenx_mem: memory@b9600000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xb9600000 0x0 0x6a00000>;
>>>>>> + };
>>>>>> +
>>>>>> + tenx_q6_buffer_mem: memory@c0000000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xc0000000 0x0 0x3200000>;
>>>>>> + };
>>>>>> +
>>>>>> + ipa_buffer_mem: memory@c3200000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xc3200000 0x0 0x12c00000>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + soc: soc@0 {
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <2>;
>>>>>> + ranges = <0 0 0 0 0x10 0>;
>>>>>> + dma-ranges = <0 0 0 0 0x10 0>;
>>>>>> + compatible = "simple-bus";
>>>>>> +
>>>>>> + gcc: clock-controller@80000 {
>>>>>> + compatible = "qcom,gcc-qdu1000", "qcom,gcc-qru1000", "syscon";
>>>>>> + reg = <0x0 0x80000 0x0 0x1f4200>;
>>>>>> + #clock-cells = <1>;
>>>>>> + #reset-cells = <1>;
>>>>>> + #power-domain-cells = <1>;
>>>>>> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
>>>>>> + clock-names = "bi_tcxo", "sleep_clk";
>>>>>> + };
>>>>>> +
>>>>>> + gpi_dma0: dma-controller@900000 {
>>>>>> + compatible = "qcom,qdu1000-gpi-dma", "qcom,qru1000-gpi-dma";
>>>>> This won't work if you drop series [1]. It won't just fail the schema checks,
>>>>> but it would also fail to probe because the driver doesn't recognise it.
>>>>>
>>>>> I think you were told to rebase on [2], and didn't change your own series
>>>>> because it only applied to ee_offset = 0x0. There is another series [3] that
>>>>> was sent to you, meant for ee_offset = 0x10000. You're expected to change your
>>>>> patches (in both series you sent) based on what was changed in that series.
>>>>>
>>>>> [1] https://lore.kernel.org/linux-arm-msm/a4db0335-33d8-76cd-6f89-b8bde603aedf@xxxxxxxxxxx/
>>>>> [2] https://lore.kernel.org/linux-arm-msm/20221018005740.23952-1-mailingradian@xxxxxxxxx/T/
>>>>> [3] https://lore.kernel.org/linux-arm-msm/20221018230352.1238479-1-krzysztof.kozlowski@xxxxxxxxxx/T/
>>>> Hi Richard; I was aware of this feedback and was planning to make that change in v3.
>>>> PS [1] will be dropped and this compatible will be modified similar to PS [3]; that was
>>>> what I meant by my final comment on [1].
>>> Ok, I should have checked the date. What about the schema patch? It might be
>>> helpful for the device tree cleanup efforts if you didn't add a compatible
>>> without adding a corresponding entry in the device tree bindings.
>>>
>>> I'm talking about updating this patch in particular:
>>>
>>> https://lore.kernel.org/linux-arm-msm/20221014221102.7445-2-quic_molvera@xxxxxxxxxxx/
>>>
>>> We still add compat strings in dt-bindings even when there is a fallback,
>>> because the schema is meant to specify every combination of compat strings
>>> found in the device trees.
>> That will be dropped as well. I'll use the sdm845 compat string instead of what's here.
> I hope you're talking about sm6350, because sdm845 has an ee_offset of 0. But if
> you think the maintainers will accept this, then it shouldn't be a problem. I
> just thought that you would copy what the other platforms are doing, which
> required a schema patch.
>
> Example:
>
> Documentation/devicetree/bindings/dma/qcom,gpi.yaml:
>
> properties:
> compatible:
> oneOf:
> - enum:
> - qcom,sdm845-gpi-dma
> - qcom,sm6350-gpi-dma
> - items:
> - enum:
> - qcom,qdu1000-gpi-dma
> - qcom,sc7280-gpi-dma
> - qcom,sm8350-gpi-dma
> - qcom,sm8450-gpi-dma
> - const: qcom,sm6350-gpi-dma
>
> and
>
> compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
>
> would pass schema checks.
>
> Documentation/devicetree/bindings/dma/qcom,gpi.yaml:
>
> properties:
> compatible:
> oneOf:
> - enum:
> - qcom,sdm845-gpi-dma
> - qcom,sm6350-gpi-dma
> - items:
> - enum:
> - qcom,sc7280-gpi-dma
> - qcom,sm8350-gpi-dma
> - qcom,sm8450-gpi-dma
> - const: qcom,sm6350-gpi-dma
>
> and
>
> compatible = "qcom,sm6350-gpi-dma";
>
> would also pass schema checks.
>
> Documentation/devicetree/bindings/dma/qcom,gpi.yaml:
>
> properties:
> compatible:
> oneOf:
> - enum:
> - qcom,sdm845-gpi-dma
> - qcom,sm6350-gpi-dma
> - items:
> - enum:
> - qcom,sc7280-gpi-dma
> - qcom,sm8350-gpi-dma
> - qcom,sm8450-gpi-dma
> - const: qcom,sm6350-gpi-dma
>
> and
>
> compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
>
> would not pass schema checks.
Yeah I meant sm6350; my bad. I'll just use that compatible and drop the qdu one.
>
>>>>>> + #dma-cells = <5>;
>>>>>> + reg = <0x0 0x900000 0x0 0x60000>;
>>>>>> + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + dma-channels = <12>;
>>>>>> + dma-channel-mask = <0x3f>;
>>>>>> + iommus = <&apps_smmu 0xf6 0x0>;
>>>>>> + status = "ok";
>>>>>> + };
>>>>>> +
>>>>>> + qupv3_id_0: geniqup@9c0000 {
>>>>>> + compatible = "qcom,geni-se-qup";
>>>>>> + reg = <0x0 0x9c0000 0x0 0x2000>;
>>>>>> + clock-names = "m-ahb", "s-ahb";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
>>>>>> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
>>>>>> + iommus = <&apps_smmu 0xe3 0x0>;
>>>>>> + interconnects = <&clk_virt MASTER_QUP_CORE_0 0
>>>>>> + &clk_virt SLAVE_QUP_CORE_0 0>;
>>>>>> + interconnect-names = "qup-core";
>>>>>> + qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
>>>>>> + qcom,iommu-geometry = <0x40000000 0x10000000>;
>>>>>> + qcom,iommu-dma = "fastmap";
>>>>>> + dma-coherent;
>>>>>> +
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <2>;
>>>>>> + ranges;
>>>>>> + status = "disabled";
>>>>>> +
>>>>>> + uart0: serial@980000 {
>>>>>> + compatible = "qcom,geni-uart";
>>>>>> + reg = <0x0 0x980000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_uart0_default>;
>>>>>> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c1: i2c@984000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x984000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>>>>>> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c1_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 1 3 64 0>,
>>>>>> + <&gpi_dma0 1 1 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi1: spi@984000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x984000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
>>>>>> + dmas = <&gpi_dma0 0 1 1 64 0>,
>>>>>> + <&gpi_dma0 1 1 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c2: i2c@988000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x988000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>>>>>> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c2_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 2 3 64 0>,
>>>>>> + <&gpi_dma0 1 2 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi2: spi@988000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x988000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
>>>>>> + dmas = <&gpi_dma0 0 2 1 64 0>,
>>>>>> + <&gpi_dma0 1 2 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c3: i2c@98c000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x98c000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>>>>>> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c3_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 3 3 64 0>,
>>>>>> + <&gpi_dma0 1 3 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi3: spi@98c000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x98c000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
>>>>>> + dmas = <&gpi_dma0 0 3 1 64 0>,
>>>>>> + <&gpi_dma0 1 3 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c4: i2c@990000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x990000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>>>>>> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c4_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 4 3 64 0>,
>>>>>> + <&gpi_dma0 1 4 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi4: spi@990000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x990000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
>>>>>> + dmas = <&gpi_dma0 0 4 1 64 0>,
>>>>>> + <&gpi_dma0 1 4 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c5: i2c@994000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x994000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>>>>>> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c5_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 5 3 64 0>,
>>>>>> + <&gpi_dma0 1 5 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi5: spi@994000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x994000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
>>>>>> + dmas = <&gpi_dma0 0 5 1 64 0>,
>>>>>> + <&gpi_dma0 1 5 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c6: i2c@998000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0x998000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
>>>>>> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c6_data_clk>;
>>>>>> + dmas = <&gpi_dma0 0 6 3 64 0>,
>>>>>> + <&gpi_dma0 1 6 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi6: spi@998000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0x998000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_0 0>,
>>>>>> + <&system_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
>>>>>> + dmas = <&gpi_dma0 0 6 1 64 0>,
>>>>>> + <&gpi_dma0 1 6 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + uart7: serial@99c000 {
>>>>>> + compatible = "qcom,geni-debug-uart";
>>>>>> + reg = <0x0 0x99c000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
>>>>>> + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + gpi_dma1: dma-controller@a00000 {
>>>>>> + compatible = "qcom,qdu1000-gpi-dma", "qcom,qru1000-gpi-dma";
>>>>> See above.
>>>>>
>>>>>> + #dma-cells = <5>;
>>>>>> + reg = <0x0 0xa00000 0x0 0x60000>;
>>>>>> + interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + dma-channels = <12>;
>>>>>> + dma-channel-mask = <0x3f>;
>>>>>> + iommus = <&apps_smmu 0x116 0x0>;
>>>>>> + status = "ok";
>>>>>> + };
>>>>>> +
>>>>>> + qupv3_id_1: geniqup@ac0000 {
>>>>>> + compatible = "qcom,geni-se-qup";
>>>>>> + reg = <0x0 0xac0000 0x0 0x2000>;
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
>>>>>> + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
>>>>>> + iommus = <&apps_smmu 0x103 0x0>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <1>;
>>>>>> + clock-names = "m-ahb", "s-ahb";
>>>>>> +
>>>>>> + ranges;
>>>>>> + status = "disabled";
>>>>>> +
>>>>>> + uart8: serial@a80000 {
>>>>>> + compatible = "qcom,geni-uart";
>>>>>> + reg = <0x0 0xa80000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_uart8_default>;
>>>>>> + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c9: i2c@a84000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa84000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
>>>>>> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c9_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 1 3 64 0>,
>>>>>> + <&gpi_dma1 1 1 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi9: spi@a84000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa84000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
>>>>>> + dmas = <&gpi_dma1 0 1 1 64 0>,
>>>>>> + <&gpi_dma1 1 1 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c10: i2c@a88000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa88000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
>>>>>> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c10_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 2 3 64 0>,
>>>>>> + <&gpi_dma1 1 2 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi10: spi@a88000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa88000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
>>>>>> + dmas = <&gpi_dma1 0 2 1 64 0>,
>>>>>> + <&gpi_dma1 1 2 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c11: i2c@a8c000 {
>>>>>> + compatible = "qcom,i2c-geni";
>>>>>> + reg = <0x0 0xa8c000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
>>>>>> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c11_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 3 3 64 0>,
>>>>>> + <&gpi_dma1 1 3 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi11: spi@a8c000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa8c000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
>>>>>> + dmas = <&gpi_dma1 0 3 1 64 0>,
>>>>>> + <&gpi_dma1 1 3 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c12: i2c@a90000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa90000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c12_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 4 3 64 0>,
>>>>>> + <&gpi_dma1 1 4 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi12: spi@a90000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa90000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
>>>>>> + dmas = <&gpi_dma1 0 4 1 64 0>,
>>>>>> + <&gpi_dma1 1 4 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c13: i2c@a94000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa94000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>>>>>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c13_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 5 3 64 0>,
>>>>>> + <&gpi_dma1 1 5 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + uart13: serial@a94000 {
>>>>>> + compatible = "qcom,geni-uart";
>>>>>> + reg = <0x0 0xa94000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_uart13_default>;
>>>>>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi13: spi@a94000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa94000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
>>>>>> + dmas = <&gpi_dma1 0 5 1 64 0>,
>>>>>> + <&gpi_dma1 1 5 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c14: i2c@a98000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa98000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
>>>>>> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c14_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 6 3 64 0>,
>>>>>> + <&gpi_dma1 1 6 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi14: spi@a98000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa98000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
>>>>>> + dmas = <&gpi_dma1 0 6 1 64 0>,
>>>>>> + <&gpi_dma1 1 6 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + i2c15: i2c@a9c000 {
>>>>>> + compatible = "qcom,geni-i2c";
>>>>>> + reg = <0x0 0xa9c000 0x0 0x4000>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
>>>>>> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_i2c15_data_clk>;
>>>>>> + dmas = <&gpi_dma1 0 7 3 64 0>,
>>>>>> + <&gpi_dma1 1 7 3 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + spi15: spi@a9c000 {
>>>>>> + compatible = "qcom,geni-spi";
>>>>>> + reg = <0x0 0xa9c000 0x0 0x4000>;
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + clock-names = "se";
>>>>>> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
>>>>>> + interconnect-names = "qup-core", "qup-config", "qup-memory";
>>>>>> + interconnects =
>>>>>> + <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
>>>>>> + <&gem_noc MASTER_APPSS_PROC 0 &system_noc SLAVE_QUP_1 0>,
>>>>>> + <&system_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
>>>>>> + dmas = <&gpi_dma1 0 7 1 64 0>,
>>>>>> + <&gpi_dma1 1 7 1 64 0>;
>>>>>> + dma-names = "tx", "rx";
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + system_noc: interconnect@1640000 {
>>>>>> + reg = <0x0 0x1640000 0x0 0x45080>;
>>>>>> + compatible = "qcom,qdu1000-system-noc", "qcom,qru1000-system-noc";
>>>>>> + #interconnect-cells = <1>;
>>>>>> + qcom,bcm-voters = <&apps_bcm_voter>;
>>>>>> + };
>>>>>> +
>>>>>> + tcsr_mutex: hwlock@1f40000 {
>>>>>> + compatible = "qcom,tcsr-mutex";
>>>>>> + reg = <0x0 0x1f40000 0x0 0x20000>;
>>>>>> + #hwlock-cells = <1>;
>>>>>> + };
>>>>>> +
>>>>>> + pdc: interrupt-controller@b220000 {
>>>>>> + compatible = "qcom,pdc";
>>>>>> + reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
>>>>>> + reg-names = "pdc-interrupt-base", "apss-shared-spi-cfg";
>>>>>> + qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
>>>>>> + <94 609 31>, <125 63 1>;
>>>>>> + #interrupt-cells = <2>;
>>>>>> + interrupt-parent = <&intc>;
>>>>>> + interrupt-controller;
>>>>>> + };
>>>>>> +
>>>>>> + spmi_bus: spmi@c400000 {
>>>>>> + compatible = "qcom,spmi-pmic-arb";
>>>>>> + reg = <0x0 0xc400000 0x0 0x3000>,
>>>>>> + <0x0 0xc500000 0x0 0x400000>,
>>>>>> + <0x0 0xc440000 0x0 0x80000>,
>>>>>> + <0x0 0xc4c0000 0x0 0x10000>,
>>>>>> + <0x0 0xc42d000 0x0 0x4000>;
>>>>>> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
>>>>>> + interrupt-names = "periph_irq";
>>>>>> + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + qcom,ee = <0>;
>>>>>> + qcom,channel = <0>;
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <0>;
>>>>>> + interrupt-controller;
>>>>>> + #interrupt-cells = <4>;
>>>>>> + };
>>>>>> +
>>>>>> + tlmm: pinctrl@f000000 {
>>>>>> + compatible = "qcom,qdu1000-tlmm", "qcom,qru1000-tlmm";
>>>>>> + reg = <0x0 0xf000000 0x0 0x1000000>;
>>>>>> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + gpio-controller;
>>>>>> + #gpio-cells = <2>;
>>>>>> + interrupt-controller;
>>>>>> + #interrupt-cells = <2>;
>>>>>> + gpio-ranges = <&tlmm 0 0 151>;
>>>>>> + wakeup-parent = <&pdc>;
>>>>>> +
>>>>>> + qup_uart0_default: qup-uart0-default-state {
>>>>>> + pins = "gpio6", "gpio7", "gpio8", "gpio9";
>>>>>> + function = "qup00";
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c1_data_clk: qup-i2c1-data-clk {
>>>>>> + pins = "gpio10", "gpio11";
>>>>>> + function = "qup01";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi1_data_clk: qup-spi1-data-clk {
>>>>>> + pins = "gpio10", "gpio11", "gpio12";
>>>>>> + function = "qup01";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi1_cs: qup-spi1-cs {
>>>>>> + pins = "gpio13";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c2_data_clk: qup-i2c2-data-clk {
>>>>>> + pins = "gpio12", "gpio13";
>>>>>> + function = "qup02";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi2_data_clk: qup-spi2-data-clk {
>>>>>> + pins = "gpio12", "gpio13", "gpio10";
>>>>>> + function = "qup02";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi2_cs: qup-spi2-cs {
>>>>>> + pins = "gpio11";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c3_data_clk: qup-i2c3-data-clk {
>>>>>> + pins = "gpio14", "gpio15";
>>>>>> + function = "qup03";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi3_data_clk: qup-spi3-data-clk {
>>>>>> + pins = "gpio14", "gpio15", "gpio16";
>>>>>> + function = "qup03";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi3_cs: qup-spi3-cs {
>>>>>> + pins = "gpio17";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c4_data_clk: qup-i2c4-data-clk {
>>>>>> + pins = "gpio16", "gpio17";
>>>>>> + function = "qup04";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi4_data_clk: qup-spi4-data-clk {
>>>>>> + pins = "gpio16", "gpio17", "gpio14";
>>>>>> + function = "qup04";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi4_cs: qup-spi4-cs {
>>>>>> + pins = "gpio15";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c5_data_clk: qup-i2c5-data-clk {
>>>>>> + pins = "gpio130", "gpio131";
>>>>>> + function = "qup05";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi5_data_clk: qup-spi5-data-clk {
>>>>>> + pins = "gpio130", "gpio131", "gpio132";
>>>>>> + function = "qup05";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi5_cs: qup-spi5-cs {
>>>>>> + pins = "gpio133";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c6_data_clk: qup-i2c6-data-clk {
>>>>>> + pins = "gpio132", "gpio133";
>>>>>> + function = "qup06";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi6_data_clk: qup-spi6-data-clk {
>>>>>> + pins = "gpio132", "gpio133", "gpio130";
>>>>>> + function = "qup06";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi6_cs: qup-spi6-cs {
>>>>>> + pins = "gpio131";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_uart7_rx: qup-uart7-rx {
>>>>>> + pins = "gpio135";
>>>>>> + function = "qup07";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_uart7_tx: qup-uart7-tx {
>>>>>> + pins = "gpio134";
>>>>>> + function = "qup07";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_uart8_default: qup-uart8-default {
>>>>>> + pins = "gpio18", "gpio19", "gpio20", "gpio21";
>>>>>> + function = "qup10";
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c9_data_clk: qup-i2c9-data-clk {
>>>>>> + pins = "gpio22", "gpio23";
>>>>>> + function = "qup11";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pull-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi9_data_clk: qup-spi9-data-clk {
>>>>>> + pins = "gpio22", "gpio23", "gpio24";
>>>>>> + function = "qup11";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi9_cs: qup-spi9-cs {
>>>>>> + pins = "gpio25";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c10_data_clk: qup-i2c10-data-clk {
>>>>>> + pins = "gpio24", "gpio25";
>>>>>> + function = "qup12";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi10_data_clk: qup-spi10-data-clk {
>>>>>> + pins = "gpio24", "gpio25", "gpio22";
>>>>>> + function = "qup12";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi10_cs: qup-spi10-cs {
>>>>>> + pins = "gpio23";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c11_data_clk: qup-i2c11-data-clk {
>>>>>> + pins = "gpio26", "gpio27";
>>>>>> + function = "qup13";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi11_data_clk: qup-spi11-data-clk {
>>>>>> + pins = "gpio26", "gpio27", "gpio28";
>>>>>> + function = "qup13";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi11_cs: qup-spi11-cs {
>>>>>> + pins = "gpio29";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c12_data_clk: qup-i2c12-data-clk {
>>>>>> + pins = "gpio28", "gpio29";
>>>>>> + function = "qup14";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi12_data_clk: qup-spi12-data-clk {
>>>>>> + pins = "gpio28", "gpio29", "gpio26";
>>>>>> + function = "qup14";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi12_cs: qup-spi12-cs {
>>>>>> + pins = "gpio27";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c13_data_clk: qup-i2c13-data-clk {
>>>>>> + pins = "gpio30", "gpio31";
>>>>>> + function = "qup15";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi13_data_clk: qup-spi13-data-clk {
>>>>>> + pins = "gpio30", "gpio31", "gpio32";
>>>>>> + function = "qup15";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi13_cs: qup-spi13-cs {
>>>>>> + pins = "gpio33";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_uart13_default: qup-uart13-default {
>>>>>> + pins = "gpio30", "gpio31", "gpio32", "gpio33";
>>>>>> + function = "qup15";
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c14_data_clk: qup-i2c14-data-clk {
>>>>>> + pins = "gpio34", "gpio35";
>>>>>> + function = "qup16";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi14_data_clk: qup-spi14-data-clk {
>>>>>> + pins = "gpio34", "gpio35", "gpio36";
>>>>>> + function = "qup16";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi14_cs: qup-spi14-cs {
>>>>>> + pins = "gpio37", "gpio38";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_i2c15_data_clk: qup-i2c15-data-clk {
>>>>>> + pins = "gpio40", "gpio41";
>>>>>> + function = "qup17";
>>>>>> + drive-strength = <2>;
>>>>>> + bias-pulll-up;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi15_data_clk: qup-spi15-data-clk {
>>>>>> + pins = "gpio40", "gpio41", "gpio30";
>>>>>> + function = "qup17";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> +
>>>>>> + qup_spi15_cs: qup-spi15-cs {
>>>>>> + pins = "gpio31";
>>>>>> + drive-strength = <6>;
>>>>>> + bias-disable;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + apps_smmu: apps-smmu@15000000 {
>>>>>> + compatible = "qcom,qdu1000-smmu-500", "qcom,qru1000-smmu-500",
>>>>>> + "arm,mmu-500";
>>>>>> + reg = <0x0 0x15000000 0x0 0x100000>;
>>>>>> + #iommu-cells = <2>;
>>>>>> + #global-interrupts = <2>;
>>>>>> + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + };
>>>>>> +
>>>>>> + intc: interrupt-controller@17200000 {
>>>>>> + compatible = "arm,gic-v3";
>>>>>> + #interrupt-cells = <3>;
>>>>>> + interrupt-controller;
>>>>>> + #redistributor-regions = <1>;
>>>>>> + redistributor-stride = <0x0 0x20000>;
>>>>>> + reg = <0x0 0x17200000 0x0 0x10000>, /* GICD */
>>>>>> + <0x0 0x17260000 0x0 0x80000>; /* GICR * 4 */
>>>>>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
>>>>>> + };
>>>>>> +
>>>>>> + timer@17420000 {
>>>>>> + compatible = "arm,armv7-timer-mem";
>>>>>> + #address-cells = <2>;
>>>>>> + #size-cells = <2>;
>>>>>> + ranges;
>>>>>> + reg = <0x0 0x17420000 0x0 0x1000>;
>>>>>> + clock-frequency = <19200000>;
>>>>>> +
>>>>>> + frame@17421000 {
>>>>>> + frame-number = <0>;
>>>>>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x17421000 0x0 0x1000>,
>>>>>> + <0x0 0x17422000 0x0 0x1000>;
>>>>>> + };
>>>>>> +
>>>>>> + frame@17423000 {
>>>>>> + frame-number = <1>;
>>>>>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x17423000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + frame@17425000 {
>>>>>> + frame-number = <2>;
>>>>>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x17425000 0x0 0x1000>,
>>>>>> + <0x0 0x17426000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + frame@17427000 {
>>>>>> + frame-number = <3>;
>>>>>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x17427000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + frame@17429000 {
>>>>>> + frame-number = <4>;
>>>>>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x17429000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + frame@1742b000 {
>>>>>> + frame-number = <5>;
>>>>>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x1742b000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + frame@1742d000 {
>>>>>> + frame-number = <6>;
>>>>>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + reg = <0x0 0x1742d000 0x0 0x1000>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + apps_rsc: rsc@17a00000 {
>>>>>> + label = "apps_rsc";
>>>>>> + compatible = "qcom,rpmh-rsc";
>>>>>> + reg = <0x0 0x17a00000 0x0 0x10000>,
>>>>>> + <0x0 0x17a10000 0x0 0x10000>,
>>>>>> + <0x0 0x17a20000 0x0 0x10000>;
>>>>>> + reg-names = "drv-0", "drv-1", "drv-2";
>>>>>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
>>>>>> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + qcom,tcs-offset = <0xd00>;
>>>>>> + qcom,drv-id = <2>;
>>>>>> + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
>>>>>> + <WAKE_TCS 3>, <CONTROL_TCS 0>;
>>>>>> +
>>>>>> + apps_bcm_voter: bcm_voter {
>>>>>> + compatible = "qcom,bcm-voter";
>>>>>> + };
>>>>>> +
>>>>>> + rpmhcc: clock-controller {
>>>>>> + compatible = "qcom,qdu1000-rpmh-clk", "qcom,qru1000-rpmh-clk";
>>>>>> + #clock-cells = <1>;
>>>>>> + clock-names = "xo";
>>>>>> + clocks = <&xo_board>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd: power-controller {
>>>>>> + compatible = "qcom,qdu1000-rpmhpd", "qcom,qru1000-rpmhpd";
>>>>>> + #power-domain-cells = <1>;
>>>>>> + operating-points-v2 = <&rpmhpd_opp_table>;
>>>>>> +
>>>>>> + rpmhpd_opp_table: opp-table {
>>>>>> + compatible = "operating-points-v2";
>>>>>> +
>>>>>> + rpmhpd_opp_ret: opp1 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_min_svs: opp2 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_low_svs: opp3 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_svs: opp4 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_svs_l1: opp5 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_nom: opp6 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_nom_l1: opp7 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_nom_l2: opp8 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_turbo: opp9 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
>>>>>> + };
>>>>>> +
>>>>>> + rpmhpd_opp_turbo_l1: opp10 {
>>>>>> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + cpufreq_hw: cpufreq@17d91000 {
>>>>>> + compatible = "qcom, qdu1000-cpufreq-epss", "qcom, qru1000-cpufreq-epss",
>>>>>> + "qcom,cpufreq-epss";
>>>>>> + reg = <0x0 0x17d91000 0x0 0x1000>;
>>>>>> + reg-names = "freq-domain0";
>>>>>> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
>>>>>> + clock-names = "xo", "alternate";
>>>>>> + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
>>>>>> + interrupt-names = "dcvsh-irq-0";
>>>>>> + #freq-domain-cells = <1>;
>>>>>> + };
>>>>>> +
>>>>>> + gem_noc: interconnect@19100000 {
>>>>>> + reg = <0x0 0x19100000 0x0 0xB8080>;
>>>>>> + compatible = "qcom,qdu1000-gem-noc", "qcom,qru1000-gem-noc";
>>>>>> + #interconnect-cells = <1>;
>>>>>> + qcom,bcm-voters = <&apps_bcm_voter>;
>>>>>> + };
>>>>>> +
>>>>>> + arch_timer: timer {
>>>>>> + compatible = "arm,armv8-timer";
>>>>>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>>>>>> + clock-frequency = <19200000>;
>>>>>> + };
>>>>>> + };
>>>>>> +};
>>>>>> diff --git a/arch/arm64/boot/dts/qcom/qru1000.dtsi b/arch/arm64/boot/dts/qcom/qru1000.dtsi
>>>>>> new file mode 100644
>>>>>> index 000000000000..074fe126e85e
>>>>>> --- /dev/null
>>>>>> +++ b/arch/arm64/boot/dts/qcom/qru1000.dtsi
>>>>>> @@ -0,0 +1,27 @@
>>>>>> +// SPDX-License-Identifier: BSD-3-Clause
>>>>>> +/*
>>>>>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
>>>>>> + */
>>>>>> +
>>>>>> +#include "qdu1000.dtsi"
>>>>>> +
>>>>>> +&reserved_memory {
>>>>>> + /delete-node/ memory@a0000000;
>>>>>> + /delete-node/ memory@b9600000;
>>>>>> + /delete-node/ memory@c0000000;
>>>>>> +
>>>>>> + oem_tenx_mem: memory@a0000000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xa0000000 0x0 0x6400000>;
>>>>>> + };
>>>>>> +
>>>>>> + mpss_diag_buffer_mem: memory@aea00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xaea00000 0x0 0x6400000>;
>>>>>> + };
>>>>>> +
>>>>>> + tenx_q6_buffer_mem: memory@b4e00000 {
>>>>>> + no-map;
>>>>>> + reg = <0x0 0xb4e00000 0x0 0x3200000>;
>>>>>> + };
>>>>>> +};
>>>>>> --
>>>>>> 2.38.0
>>>> Thanks,
>>>> Melody