[PATCH v4 09/13] dt-bindings: pinctrl: mediatek,mt6779-pinctrl: Add MT6795

From: Yassine Oudjana
Date: Fri Oct 28 2022 - 11:36:29 EST

From: Yassine Oudjana <y.oudjana@xxxxxxxxxxxxxx>

Combine MT6795 pin controller document into MT6779 one. In the
process, amend the example with comments and additional pinctrl
nodes from the MT6795 example, replace the current interrupts
property description with the one from the MT6795 document since
it makes more sense and define its items using conditionals
as they now vary between variants. Also use conditionals to define
valid values for the drive-strength property for each variant.

Signed-off-by: Yassine Oudjana <y.oudjana@xxxxxxxxxxxxxx>
---
.../pinctrl/mediatek,mt6779-pinctrl.yaml | 189 ++++++++++-----
.../pinctrl/mediatek,pinctrl-mt6795.yaml | 227 ------------------
2 files changed, 127 insertions(+), 289 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
index 70e4ffa2d897..6f2cffe50b11 100644
--- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
@@ -8,6 +8,7 @@ title: Mediatek MT6779 Pin Controller

maintainers:
- Andy Teng <andy.teng@xxxxxxxxxxxx>
+ - AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
- Sean Wang <sean.wang@xxxxxxxxxx>

description:
@@ -18,6 +19,7 @@ properties:
compatible:
enum:
- mediatek,mt6779-pinctrl
+ - mediatek,mt6795-pinctrl
- mediatek,mt6797-pinctrl

reg:
@@ -43,9 +45,7 @@ properties:
interrupt-controller: true

interrupts:
- maxItems: 1
- description: |
- Specifies the summary IRQ.
+ description: Interrupt outputs to the system interrupt controller (sysirq).

"#interrupt-cells":
const: 2
@@ -57,59 +57,6 @@ required:
- gpio-controller
- "#gpio-cells"

-allOf:
- - $ref: "pinctrl.yaml#"
- - if:
- properties:
- compatible:
- contains:
- const: mediatek,mt6779-pinctrl
- then:
- properties:
- reg:
- minItems: 9
- maxItems: 9
-
- reg-names:
- items:
- - const: gpio
- - const: iocfg_rm
- - const: iocfg_br
- - const: iocfg_lm
- - const: iocfg_lb
- - const: iocfg_rt
- - const: iocfg_lt
- - const: iocfg_tl
- - const: eint
- - if:
- properties:
- compatible:
- contains:
- const: mediatek,mt6797-pinctrl
- then:
- properties:
- reg:
- minItems: 5
- maxItems: 5
-
- reg-names:
- items:
- - const: gpio
- - const: iocfgl
- - const: iocfgb
- - const: iocfgr
- - const: iocfgt
- - if:
- properties:
- reg-names:
- contains:
- const: eint
- then:
- required:
- - interrupts
- - interrupt-controller
- - "#interrupt-cells"
-
patternProperties:
'-pins$':
type: object
@@ -169,8 +116,7 @@ patternProperties:

input-schmitt-disable: true

- drive-strength:
- enum: [2, 4, 8, 12, 16]
+ drive-strength: true

slew-rate:
enum: [0, 1]
@@ -202,6 +148,110 @@ patternProperties:

additionalProperties: false

+allOf:
+ - $ref: "pinctrl.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: mediatek,mt6779-pinctrl
+ then:
+ properties:
+ reg:
+ minItems: 9
+ maxItems: 9
+
+ reg-names:
+ items:
+ - const: gpio
+ - const: iocfg_rm
+ - const: iocfg_br
+ - const: iocfg_lm
+ - const: iocfg_lb
+ - const: iocfg_rt
+ - const: iocfg_lt
+ - const: iocfg_tl
+ - const: eint
+
+ interrupts:
+ items:
+ - description: EINT interrupt
+
+ patternProperties:
+ '-pins$':
+ patternProperties:
+ '^pins':
+ properties:
+ drive-strength:
+ enum: [2, 4, 8, 12, 16]
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: mediatek,mt6795-pinctrl
+ then:
+ properties:
+ reg:
+ minItems: 2
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: base
+ - const: eint
+
+ interrupts:
+ items:
+ - description: EINT interrupt
+ - description: EINT event_b interrupt
+
+ patternProperties:
+ '-pins$':
+ patternProperties:
+ '^pins':
+ properties:
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: mediatek,mt6797-pinctrl
+ then:
+ properties:
+ reg:
+ minItems: 5
+ maxItems: 5
+
+ reg-names:
+ items:
+ - const: gpio
+ - const: iocfgl
+ - const: iocfgb
+ - const: iocfgr
+ - const: iocfgt
+
+ patternProperties:
+ '-pins$':
+ patternProperties:
+ '^pins':
+ properties:
+ drive-strength:
+ enum: [2, 4, 8, 12, 16]
+
+ - if:
+ properties:
+ reg-names:
+ contains:
+ const: eint
+ then:
+ required:
+ - interrupts
+ - interrupt-controller
+ - "#interrupt-cells"
+
additionalProperties: false

examples:
@@ -237,8 +287,9 @@ examples:
#interrupt-cells = <2>;
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;

- mmc0_pins_default: mmc0-0 {
- cmd-dat-pins {
+ /* GPIOs 167-174, 176-178 set as multifunction MSDC0 */
+ mmc0_pins_default: mmc0-pins {
+ pins-cmd-dat {
pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
<PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
@@ -251,15 +302,29 @@ examples:
input-enable;
mediatek,pull-up-adv = <1>;
};
- clk-pins {
+ pins-clk {
pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
mediatek,pull-down-adv = <2>;
};
- rst-pins {
+ pins-rst {
pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
mediatek,pull-up-adv = <0>;
};
};
+
+ /* GPIO0 set as multifunction GPIO0 */
+ gpio-pins {
+ pins {
+ pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
+ };
+ };
+
+ /* GPIO52 set as multifunction SDA0 */
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO52__FUNC_SDA0>;
+ };
+ };
};

mmc0 {
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml
deleted file mode 100644
index 9399e0215526..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml
+++ /dev/null
@@ -1,227 +0,0 @@
-# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/pinctrl/mediatek,pinctrl-mt6795.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Mediatek MT6795 Pin Controller
-
-maintainers:
- - AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
- - Sean Wang <sean.wang@xxxxxxxxxx>
-
-description: |
- The Mediatek's Pin controller is used to control SoC pins.
-
-properties:
- compatible:
- const: mediatek,mt6795-pinctrl
-
- gpio-controller: true
-
- '#gpio-cells':
- description: |
- Number of cells in GPIO specifier. Since the generic GPIO binding is used,
- the amount of cells must be specified as 2. See the below
- mentioned gpio binding representation for description of particular cells.
- const: 2
-
- gpio-ranges:
- description: GPIO valid number range.
- maxItems: 1
-
- reg:
- description:
- Physical address base for gpio base and eint registers.
- minItems: 2
-
- reg-names:
- items:
- - const: base
- - const: eint
-
- interrupt-controller: true
-
- '#interrupt-cells':
- const: 2
-
- interrupts:
- description: Interrupt outputs to the system interrupt controller (sysirq).
- minItems: 1
- items:
- - description: EINT interrupt
- - description: EINT event_b interrupt
-
-# PIN CONFIGURATION NODES
-patternProperties:
- '-pins$':
- type: object
- additionalProperties: false
- patternProperties:
- '^pins':
- type: object
- additionalProperties: false
- description: |
- A pinctrl node should contain at least one subnodes representing the
- pinctrl groups available on the machine. Each subnode will list the
- pins it needs, and how they should be configured, with regard to muxer
- configuration, pullups, drive strength, input enable/disable and
- input schmitt.
- An example of using macro:
- pincontroller {
- /* GPIO0 set as multifunction GPIO0 */
- gpio-pins {
- pins {
- pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
- }
- };
- /* GPIO45 set as multifunction SDA0 */
- i2c0-pins {
- pins {
- pinmux = <PINMUX_GPIO45__FUNC_SDA0>;
- }
- };
- };
- $ref: "pinmux-node.yaml"
-
- properties:
- pinmux:
- description: |
- Integer array, represents gpio pin number and mux setting.
- Supported pin number and mux varies for different SoCs, and are
- defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
- directly.
-
- drive-strength:
- enum: [2, 4, 6, 8, 10, 12, 14, 16]
-
- bias-pull-down:
- oneOf:
- - type: boolean
- - enum: [100, 101, 102, 103]
- description: mt6795 pull down PUPD/R0/R1 type define value.
- description: |
- For normal pull down type, it is not necessary to specify R1R0
- values; When pull down type is PUPD/R0/R1, adding R1R0 defines
- will set different resistance values.
-
- bias-pull-up:
- oneOf:
- - type: boolean
- - enum: [100, 101, 102, 103]
- description: mt6795 pull up PUPD/R0/R1 type define value.
- description: |
- For normal pull up type, it is not necessary to specify R1R0
- values; When pull up type is PUPD/R0/R1, adding R1R0 defines
- will set different resistance values.
-
- bias-disable: true
-
- output-high: true
-
- output-low: true
-
- input-enable: true
-
- input-disable: true
-
- input-schmitt-enable: true
-
- input-schmitt-disable: true
-
- mediatek,pull-up-adv:
- description: |
- Pull up setings for 2 pull resistors, R0 and R1. User can
- configure those special pins. Valid arguments are described as below:
- 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
- 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
- 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
- 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [0, 1, 2, 3]
-
- mediatek,pull-down-adv:
- description: |
- Pull down settings for 2 pull resistors, R0 and R1. User can
- configure those special pins. Valid arguments are described as below:
- 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
- 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
- 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
- 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [0, 1, 2, 3]
-
- required:
- - pinmux
-
-allOf:
- - $ref: "pinctrl.yaml#"
-
-required:
- - compatible
- - reg
- - reg-names
- - interrupts
- - interrupt-controller
- - '#interrupt-cells'
- - gpio-controller
- - '#gpio-cells'
- - gpio-ranges
-
-additionalProperties: false
-
-examples:
- - |
- #include <dt-bindings/interrupt-controller/arm-gic.h>
- #include <dt-bindings/interrupt-controller/irq.h>
- #include <dt-bindings/pinctrl/mt6795-pinfunc.h>
-
- soc {
- #address-cells = <2>;
- #size-cells = <2>;
-
- pio: pinctrl@10005000 {
- compatible = "mediatek,mt6795-pinctrl";
- reg = <0 0x10005000 0 0x1000>, <0 0x1000b000 0 0x1000>;
- reg-names = "base", "eint";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pio 0 0 196>;
- interrupt-controller;
- interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
- #interrupt-cells = <2>;
-
- i2c0-pins {
- pins-sda-scl {
- pinmux = <PINMUX_GPIO45__FUNC_SDA0>,
- <PINMUX_GPIO46__FUNC_SCL0>;
- };
- };
-
- mmc0-pins {
- pins-cmd-dat {
- pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>,
- <PINMUX_GPIO155__FUNC_MSDC0_DAT1>,
- <PINMUX_GPIO156__FUNC_MSDC0_DAT2>,
- <PINMUX_GPIO157__FUNC_MSDC0_DAT3>,
- <PINMUX_GPIO158__FUNC_MSDC0_DAT4>,
- <PINMUX_GPIO159__FUNC_MSDC0_DAT5>,
- <PINMUX_GPIO160__FUNC_MSDC0_DAT6>,
- <PINMUX_GPIO161__FUNC_MSDC0_DAT7>,
- <PINMUX_GPIO162__FUNC_MSDC0_CMD>;
- input-enable;
- bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
- };
-
- pins-clk {
- pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>;
- bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
- };
-
- pins-rst {
- pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>;
- bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
- };
- };
- };
- };
--
2.38.1