RE: [PATCH v3 1/2] Bluetooth: Add hci_nxp to hci_uart module to support NXP BT chipsets
From: Sherry Sun
Date: Thu Nov 24 2022 - 03:53:12 EST
> -----Original Message-----
> From: Neeraj sanjay kale <neeraj.sanjaykale@xxxxxxx>
> Sent: 2022年11月23日 20:44
> To: marcel@xxxxxxxxxxxx; johan.hedberg@xxxxxxxxx;
> luiz.dentz@xxxxxxxxx; pmenzel@xxxxxxxxxxxxx; Amitkumar Karwar
> <amitkumar.karwar@xxxxxxx>; Rohit Fule <rohit.fule@xxxxxxx>; Sherry
> Sun <sherry.sun@xxxxxxx>
> Cc: Neeraj sanjay kale <neeraj.sanjaykale@xxxxxxx>; linux-
> kernel@xxxxxxxxxxxxxxx; linux-bluetooth@xxxxxxxxxxxxxxx
> Subject: [PATCH v3 1/2] Bluetooth: Add hci_nxp to hci_uart module to
> support NXP BT chipsets
>
> Add hci_nxp to the hci_uart module which adds support for the NXP BT chips.
> This driver has Power Save feature that will put the NXP bluetooth chip into
> sleep state, whenever there is no activity for certain duration of time
> (2000ms), and will be woken up when any activity is to be initiated.
>
> The Power Save feature can (optionally) be configured with the following set
> of commands:
> hcitool -i hci0 cmd 3F 23 02 00 00 (disable Power Save)
> hcitool -i hci0 cmd 3F 23 03 00 00 (enable Power Save)
> where,
> OGF = 0x3F (vendor specific command)
> OCF = 0x23 (command to set Power Save state) arg[0] = 0x02 (disable Power
> Save) arg[0] = 0x03 (enable Power Save) arg[1,2,...] = XX (don't care)
Hi Neeraj,
Below are the macros that you defined in the head file, 0x02 should be PS enable, 0x03 should be PS disable.
Seems don't align with what you described here.
/** Bluetooth Power State : Enable */
#define BT_PS_ENABLE 0x02
/** Bluetooth Power State : Disable */
#define BT_PS_DISABLE 0x03
>
> The sleep/wake-up source can be configured with the following set of
> commands:
> hcitool -i hci0 cmd 3F 53 03 14 01 FF (set UART break method)
> hcitool -i hci0 cmd 3F 53 03 14 00 FF (set UART DSR method)
> where,
> OGF = 0x3F (vendor specific command)
> OCF = 0x53 (command to set sleep and wake-up source) arg[0] = 0x00 (Chip
> to host method NONE) arg[0] = 0x01 (Chip to host method UART DTR) arg[0]
> = 0x02 (Chip to host method UART BREAK) arg[0] = 0x03 (Chip to host
> method GPIO) arg[1] = 0x14 (Chip to host GPIO[20] if arg[0] is 0x03, else 0xFF)
> arg[2] = 0x00 (Host to chip method UART DSR) arg[2] = 0x01 (Host to chip
> method UART BREAK) arg[3] = 0xXX (Reserved for future use)
>
> By default, the hci_nxp sets power save enable, chip to host wake-up source
> as GPIO and host to chip sleep and wake-up source as UART break during
> driver initialization, by sending the respective commands to the chip.
>
> Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@xxxxxxx>
> ---
> v2: Changed the subject/summary lines and added more details in the
> description. (Paul Menzel)
> v3: Made internal functions static, optimized the code, added few comments.
> (Sherry Sun)
> ---
> MAINTAINERS | 6 +
> drivers/bluetooth/Kconfig | 10 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/hci_ldisc.c | 6 +
> drivers/bluetooth/hci_nxp.c | 764
> ++++++++++++++++++++++++++++++++++++++++++
> drivers/bluetooth/hci_nxp.h | 110 ++++++
> drivers/bluetooth/hci_uart.h | 8 +-
> 7 files changed, 904 insertions(+), 1 deletion(-) create mode 100644
> drivers/bluetooth/hci_nxp.c create mode 100644
> drivers/bluetooth/hci_nxp.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index e55a4d4..70f802d 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -22591,6 +22591,12 @@ L: linux-mm@xxxxxxxxx
> S: Maintained
> F: mm/zswap.c
>
> +NXP BLUETOOTH WIRELESS DRIVERS
> +M: Amitkumar Karwar <amitkumar.karwar@xxxxxxx>
> +M: Neeraj Kale <neeraj.sanjaykale@xxxxxx>m
Typing error?
> +S: Maintained
> +F: drivers/bluetooth/hci_nxp*
> +
> THE REST
> M: Linus Torvalds <torvalds@xxxxxxxxxxxxxxxxxxxx>
> L: linux-kernel@xxxxxxxxxxxxxxx
> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig index
> 89b4d47..7f6d1dc 100644
> --- a/drivers/bluetooth/Kconfig
> +++ b/drivers/bluetooth/Kconfig
> @@ -273,6 +273,16 @@ config BT_HCIUART_MRVL
>
> Say Y here to compile support for HCI MRVL protocol.
>
> +config BT_HCIUART_NXP
> + bool "NXP protocol support"
> + depends on BT_HCIUART
> + help
> + NXP is serial protocol for communication between Bluetooth
> + device and host. This protocol is required for most NXP Bluetooth
> + devices with UART interface.
> +
> + Say Y here to compile support for HCI NXP protocol.
> +
> config BT_HCIBCM203X
> tristate "HCI BCM203x USB driver"
> depends on USB
> diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile index
> 3321a8a..bc80329 100644
> --- a/drivers/bluetooth/Makefile
> +++ b/drivers/bluetooth/Makefile
> @@ -48,4 +48,5 @@ hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
> hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
> hci_uart-$(CONFIG_BT_HCIUART_AG6XX) += hci_ag6xx.o
> hci_uart-$(CONFIG_BT_HCIUART_MRVL) += hci_mrvl.o
> +hci_uart-$(CONFIG_BT_HCIUART_NXP) += hci_nxp.o
> hci_uart-objs := $(hci_uart-y)
> diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c index
> 865112e..f3c85c2 100644
> --- a/drivers/bluetooth/hci_ldisc.c
> +++ b/drivers/bluetooth/hci_ldisc.c
> @@ -882,6 +882,9 @@ static int __init hci_uart_init(void) #ifdef
> CONFIG_BT_HCIUART_MRVL
> mrvl_init();
> #endif
> +#ifdef CONFIG_BT_HCIUART_NXP
> + nxp_init();
> +#endif
>
> return 0;
> }
> @@ -918,6 +921,9 @@ static void __exit hci_uart_exit(void) #ifdef
> CONFIG_BT_HCIUART_MRVL
> mrvl_deinit();
> #endif
> +#ifdef CONFIG_BT_HCIUART_NXP
> + nxp_deinit();
> +#endif
>
> tty_unregister_ldisc(&hci_uart_ldisc);
> }
> diff --git a/drivers/bluetooth/hci_nxp.c b/drivers/bluetooth/hci_nxp.c new
> file mode 100644 index 0000000..1508edd
> --- /dev/null
> +++ b/drivers/bluetooth/hci_nxp.c
> @@ -0,0 +1,764 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + *
> + * Bluetooth HCI UART driver
> + * Copyright 2018-2022 NXP
> + *
> + *
> + * This program is free software; you can redistribute it and/or
> +modify
> + * it under the terms of the GNU General Public License as published
> +by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/module.h>
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/types.h>
> +#include <linux/fcntl.h>
> +#include <linux/interrupt.h>
> +#include <linux/ptrace.h>
> +#include <linux/poll.h>
> +
> +#include <linux/slab.h>
> +#include <linux/tty.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/signal.h>
> +#include <linux/ioctl.h>
> +#include <linux/skbuff.h>
> +#include <asm/unaligned.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci_core.h>
> +
> +#include "hci_uart.h"
> +#include "hci_nxp.h"
> +
> +/** NXP Power Save Feature **/
/* */, one '*' please, same for other code in the driver.
> +struct BT_CMD {
> + u16 ocf_ogf;
> + u8 length;
> + u8 data[4];
> +} __packed;
> +
> +/* Power Save feature will be enabled and wakeup method will be break
> +signal by default */ int wakeupmode = WAKEUP_METHOD_BREAK; int
> ps_mode
> += PS_MODE_ENABLE;
> +
> +static int is_device_ready(struct hci_uart *hu) {
> + struct hci_dev *hdev = NULL;
> +
> + if (!hu) {
> + BT_ERR("hu is NULL");
> + return -ENODEV;
> + }
> + if (!hu->proto || !hu->hdev || !hu->tty) {
> + BT_ERR("Device not ready! proto=%p, hdev=%p, tty=%p", hu-
> >proto, hu->hdev, hu->tty);
> + return -ENODEV;
> + }
> + hdev = hu->hdev;
> + if (!test_bit(HCI_RUNNING, &hdev->flags)) {
> + BT_ERR("HCI_RUNNING is not set");
> + return -EBUSY;
> + }
> + return 0;
> +}
> +
> +/* Builds and sends a PS command packet to chip */ static int
> +send_ps_cmd(u8 cmd, struct hci_uart *hu) {
> + int err = 0;
> + struct sk_buff *skb = NULL;
> + struct BT_CMD *pcmd;
> +
> + /* allocate packet */
> + skb = bt_skb_alloc(sizeof(struct BT_CMD), GFP_ATOMIC);
> + if (!skb) {
> + BT_ERR("cannot allocate memory for HCILL packet");
> + err = -ENOMEM;
> + goto out;
> + }
> +
> + pcmd = (struct BT_CMD *)skb->data;
> + pcmd->ocf_ogf = (OGF << 10) | BT_CMD_AUTO_SLEEP_MODE;
> + pcmd->length = 1;
> + if (cmd == PS_MODE_ENABLE)
> + pcmd->data[0] = BT_PS_ENABLE;
> + else
> + pcmd->data[0] = BT_PS_DISABLE;
> +
> + bt_cb(skb)->pkt_type = HCI_COMMAND_PKT;
> + skb_put(skb, sizeof(struct BT_CMD) - 4 + pcmd->length);
> + skb->dev = (void *)hu->hdev;
> +
> + /* send packet */
> + hu->proto->enqueue(hu, skb);
> + hci_uart_tx_wakeup(hu);
> +
> +out:
> + return err;
> +}
> +
> +/* Builds and sends an wake up method command packet to chip */ static
> +int send_wakeup_method_cmd(u8 cmd, struct hci_uart *hu) {
> + int err = 0;
> + struct sk_buff *skb = NULL;
> + struct BT_CMD *pcmd;
> +
> + /* allocate packet */
> + skb = bt_skb_alloc(sizeof(struct BT_CMD), GFP_ATOMIC);
> + if (!skb) {
> + BT_ERR("cannot allocate memory for HCILL packet");
> + err = -ENOMEM;
> + goto out;
> + }
> +
> + pcmd = (struct BT_CMD *)skb->data;
> + pcmd->ocf_ogf = (OGF << 10) | BT_CMD_WAKEUP_METHOD;
> + pcmd->length = 4;
> + pcmd->data[0] = BT_HOST_WAKEUP_METHOD_NONE;
> + pcmd->data[1] = BT_HOST_WAKEUP_DEFAULT_GPIO;
> + switch (cmd) {
> + case WAKEUP_METHOD_DTR:
> + pcmd->data[2] = BT_CTRL_WAKEUP_METHOD_DSR;
> + break;
> + case WAKEUP_METHOD_BREAK:
> + default:
> + pcmd->data[2] = BT_CTRL_WAKEUP_METHOD_BREAK;
> + break;
> + }
> + pcmd->data[3] = 0xFF;
> +
> + bt_cb(skb)->pkt_type = HCI_COMMAND_PKT;
> +
> + skb_put(skb, sizeof(struct BT_CMD) - 4 + pcmd->length);
> + skb->dev = (void *)hu->hdev;
> +
> + /* send packet */
> + hu->proto->enqueue(hu, skb);
> + hci_uart_tx_wakeup(hu);
> +
> +out:
> + return err;
> +}
> +
> +static void ps_start_timer(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> +
> + if (psdata->cur_psmode == PS_MODE_ENABLE) {
> + psdata->timer_on = 1;
> + mod_timer(&psdata->ps_timer, jiffies + (psdata->interval *
> HZ) / 1000);
> + }
> +}
> +
> +static void ps_timeout_func(struct timer_list *t) {
> + struct ps_data *data = from_timer(data, t, ps_timer);
> + struct tty_struct *tty = data->tty;
> + struct hci_uart *hu = NULL;
> +
> + data->timer_on = 0;
> + if (!data->tty)
> + return;
> +
> + hu = (struct hci_uart *)tty->disc_data;
> + if (!hu)
> + return;
> +
> + if (test_bit(HCI_UART_SENDING, &hu->tx_state)) {
> + ps_start_timer(hu);
> + } else {
> + data->ps_cmd = PS_CMD_ENTER_PS;
> + schedule_work(&data->work);
> + }
> +}
> +
> +static void set_dtr(struct tty_struct *tty, int on_off) {
> + u32 old_state = 0;
> + u32 new_state = 0;
> +
> + if (TTY_FUNC->tiocmget) {
> + old_state = TTY_FUNC->tiocmget(tty);
> + if (on_off)
> + new_state = old_state | TIOCM_DTR;
> + else
> + new_state = old_state & ~TIOCM_DTR;
> + if (new_state == old_state)
> + return;
> + if (TTY_FUNC->tiocmset) {
> + if (on_off)
> + TTY_FUNC->tiocmset(tty, TIOCM_DTR, 0); /*
> DTR ON */
> + else
> + TTY_FUNC->tiocmset(tty, 0, TIOCM_DTR); /*
> DTR OFF */
> + }
> + }
> +}
> +
> +static void set_break(struct tty_struct *tty, int on_off) {
> + if (TTY_FUNC->break_ctl) {
> + if (on_off)
> + TTY_FUNC->break_ctl(tty, -1); /* turn on break */
> + else
> + TTY_FUNC->break_ctl(tty, 0); /* turn off break */
> + }
> +}
> +
> +static int get_cts(struct tty_struct *tty) {
> + u32 state = 0;
> + int ret = -1;
> +
> + if (TTY_FUNC->tiocmget) {
> + state = TTY_FUNC->tiocmget(tty);
> + if (state & TIOCM_CTS)
> + ret = 1; /* CTS LOW */
> + else
> + ret = 0; /* CTS HIGH */
> + }
> + return ret;
> +}
> +
> +static void set_rts(struct tty_struct *tty, int on_off) {
> + u32 old_state = 0;
> + u32 new_state = 0;
> +
> + if (TTY_FUNC->tiocmget) {
> + old_state = TTY_FUNC->tiocmget(tty);
> + if (on_off)
> + new_state = old_state | TIOCM_RTS;
> + else
> + new_state = old_state & ~TIOCM_RTS;
> + if (new_state == old_state)
> + return;
> + if (TTY_FUNC->tiocmset) {
> + if (on_off)
> + TTY_FUNC->tiocmset(tty, TIOCM_RTS, 0); /*
> RTS ON */
> + else
> + TTY_FUNC->tiocmset(tty, 0, TIOCM_RTS); /*
> RTS OFF */
> + }
> + }
> +}
> +
> +static void ps_control(struct ps_data *data, u8 ps_state) {
> + struct hci_uart *hu = NULL;
> +
> + if (data->ps_state == ps_state)
> + return;
> +
> + if (data->tty) {
> + switch (data->cur_wakeupmode) {
> + case WAKEUP_METHOD_DTR:
> + if (ps_state == PS_STATE_AWAKE)
> + set_dtr(data->tty, 1); /* DTR ON */
> + else
> + set_dtr(data->tty, 0); /* DTR OFF */
> + break;
> + case WAKEUP_METHOD_BREAK:
> + if (ps_state == PS_STATE_AWAKE)
> + set_break(data->tty, 0); /* break OFF */
> + else
> + set_break(data->tty, 1); /* break ON */
> + break;
> + default:
> + break;
> + }
> + data->ps_state = ps_state;
> +
> + if (ps_state == PS_STATE_AWAKE) {
> + hu = (struct hci_uart *)data->tty->disc_data;
> + if (hu)
> + hci_uart_tx_wakeup(hu);
> + }
> + }
> +}
> +
> +static void ps_work_func(struct work_struct *work) {
> + struct ps_data *data = container_of(work, struct ps_data, work);
> +
> + if (data->tty) {
> + if (data->ps_cmd == PS_CMD_ENTER_PS && data-
> >cur_psmode == PS_MODE_ENABLE)
> + ps_control(data, PS_STATE_SLEEP);
> + else if (data->ps_cmd == PS_CMD_EXIT_PS)
> + ps_control(data, PS_STATE_AWAKE);
> + }
> +}
> +
> +static int ps_init_work(struct hci_uart *hu) {
> + struct ps_data *psdata = kzalloc(sizeof(*psdata), GFP_KERNEL);
> + struct nxp_struct *nxp = hu->priv;
> +
> + if (!psdata) {
> + BT_ERR("Can't allocate control structure");
> + return -ENFILE;
> + }
> + nxp->psdata = psdata;
> +
> + memset(psdata, 0, sizeof(*psdata));
> + psdata->interval = DEFAULT_TIME_PERIOD;
> + psdata->timer_on = 0;
> + psdata->tty = NULL;
> + psdata->ps_state = PS_STATE_AWAKE;
> + psdata->ps_mode = ps_mode;
> + psdata->ps_cmd = 0;
> + psdata->send_cmd = 0;
> + switch (wakeupmode) {
> + case WAKEUP_METHOD_DTR:
> + psdata->wakeupmode = WAKEUP_METHOD_DTR;
> + break;
> + case WAKEUP_METHOD_BREAK:
> + default:
> + psdata->wakeupmode = WAKEUP_METHOD_BREAK;
> + break;
> + }
> +
> + psdata->cur_psmode = PS_MODE_DISABLE;
> + psdata->cur_wakeupmode = WAKEUP_METHOD_INVALID;
> +
> + INIT_WORK(&psdata->work, ps_work_func);
> + return 0;
> +}
> +
> +static void ps_init_timer(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> +
> + psdata->timer_on = 0;
> + psdata->tty = hu->tty;
> + timer_setup(&psdata->ps_timer, ps_timeout_func, 0); }
> +
> +static void ps_cancel_timer(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> +
> + if (psdata) {
> + flush_scheduled_work();
> + if (psdata->timer_on)
> + del_timer(&psdata->ps_timer);
> + if (psdata->cur_psmode == PS_MODE_ENABLE) {
> + switch (psdata->cur_wakeupmode) {
> + case WAKEUP_METHOD_BREAK:
> + set_break(psdata->tty, 0); /* set_break off */
> + break;
> + case WAKEUP_METHOD_DTR:
> + set_dtr(psdata->tty, 1); /* dtr on */
> + break;
> + default:
> + break;
> + }
> + }
> + psdata->tty = NULL;
> + kfree(psdata);
> + }
> +}
> +
> +static int ps_wakeup(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> + int ret = 1;
> +
> + if (psdata->ps_state == PS_STATE_AWAKE)
> + ret = 0;
> + psdata->ps_cmd = PS_CMD_EXIT_PS;
> + schedule_work(&psdata->work);
> + return ret;
> +}
> +
> +static void ps_init(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> + int mode = 0;
> + struct ktermios old_termios;
> +
> + if (!psdata || !psdata->tty)
> + return;
> + if (get_cts(psdata->tty) != 1) {
> + /* CTS is not low, chip is either sleeping */
> + /* or flow control is not enabled */
Comment style is not right. For the comment more than one line, please use
/* balabala....
* balabala....
*/
> + old_termios = psdata->tty->termios;
> + psdata->tty->termios.c_cflag &= ~CRTSCTS; /* Clear the flow
> control */
> + psdata->TTY_FUNC->set_termios(psdata->tty, &old_termios);
> + old_termios = psdata->tty->termios;
> + psdata->tty->termios.c_cflag |= CRTSCTS; /* Enable the flow
> control */
> + psdata->TTY_FUNC->set_termios(psdata->tty, &old_termios);
> +
> + /* Wake up the chip */
> + mode = psdata->cur_wakeupmode;
> + if (mode == WAKEUP_METHOD_INVALID)
> + mode = wakeupmode;
> + switch (mode) {
> + case WAKEUP_METHOD_BREAK:
> + set_rts(psdata->tty, 1); /* set RTS */
> + set_break(psdata->tty, 1); /* break on */
> + set_break(psdata->tty, 0); /* break off */
> + mdelay(5);
> + break;
> + case WAKEUP_METHOD_DTR:
> + set_rts(psdata->tty, 1); /* set RTS */
> + set_dtr(psdata->tty, 0); /* dtr off */
> + set_dtr(psdata->tty, 1); /* dtr on */
> + mdelay(5);
> + break;
> + default:
> + break;
> + }
> + }
> +
> + psdata->send_cmd = 0;
> + if (!is_device_ready(hu)) {
> + if (psdata->cur_wakeupmode != psdata->wakeupmode) {
> + psdata->send_cmd |=
> SEND_WAKEUP_METHOD_CMD;
> + send_wakeup_method_cmd(psdata->wakeupmode,
> hu);
> + }
> + if (psdata->cur_psmode != psdata->ps_mode) {
> + psdata->send_cmd |=
> SEND_AUTO_SLEEP_MODE_CMD;
> + send_ps_cmd(psdata->ps_mode, hu);
> + }
> + }
> +}
> +
> +static void ps_check_event_packet(struct hci_uart *hu, struct sk_buff
> +*skb) {
> + struct hci_event_hdr *hdr = (void *)skb->data;
> + struct hci_ev_cmd_complete *ev = NULL;
> + u8 event = hdr->evt;
> + u16 opcode;
> + u8 status = 0;
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> +
> + if (event == HCI_EV_CMD_COMPLETE) {
> + ev = (void *)(skb->data + sizeof(struct hci_event_hdr));
> + opcode = __le16_to_cpu(ev->opcode);
> + switch (opcode) {
> + case HCI_OP_AUTO_SLEEP_MODE:
> + status = *((u8 *)ev + sizeof(struct
> hci_ev_cmd_complete));
> + if (!status)
> + psdata->cur_psmode = psdata->ps_mode;
> + else
> + psdata->ps_mode = psdata->cur_psmode;
> + /* if driver has sent the command internally */
> + if (psdata->send_cmd)
> + psdata->send_cmd &=
> ~SEND_AUTO_SLEEP_MODE_CMD;
> + if (psdata->cur_psmode == PS_MODE_ENABLE)
> + ps_start_timer(hu);
> + else
> + ps_wakeup(hu);
> + BT_INFO("Power Save mode response: status=%d,
> ps_mode=%d",
> + status, psdata->cur_psmode);
> + break;
> + case HCI_OP_WAKEUP_METHOD:
> + status = *((u8 *)ev + sizeof(struct
> hci_ev_cmd_complete));
> + if (!status)
> + psdata->cur_wakeupmode = psdata-
> >wakeupmode;
> + else
> + psdata->wakeupmode = psdata-
> >cur_wakeupmode;
> + /* if driver has sent the command internally */
> + if (psdata->send_cmd)
> + psdata->send_cmd &=
> ~SEND_WAKEUP_METHOD_CMD;
> + BT_INFO("Set Wakeup Method response: status=%d,
> wakeupmode=%d",
> + status, psdata->cur_wakeupmode);
> + break;
> + default:
> + break;
> + }
> + }
> +}
> +
> +/** NXP proto **/
> +
> +/* Initialize protocol */
> +static int nxp_open(struct hci_uart *hu) {
> + struct nxp_struct *nxp;
> +
> + BT_DBG("hu %p", hu);
> +
> + nxp = kzalloc(sizeof(*nxp), GFP_KERNEL);
> + if (!nxp)
> + return -ENOMEM;
> +
> + skb_queue_head_init(&nxp->txq);
> +
> + hu->priv = nxp;
> +
> + if (ps_init_work(hu) == 0)
> + ps_init_timer(hu);
> +
> + return 0;
> +}
> +
> +/* Flush protocol data */
> +static int nxp_flush(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> +
> + BT_DBG("hu %p", hu);
> +
> + skb_queue_purge(&nxp->txq);
> +
> + return 0;
> +}
> +
> +/* Close protocol */
> +static int nxp_close(struct hci_uart *hu) {
> + struct nxp_struct *nxp = hu->priv;
> +
> + BT_DBG("hu %p", hu);
> +
> + ps_cancel_timer(hu);
> +
> + skb_queue_purge(&nxp->txq);
> +
> + kfree_skb(nxp->rx_skb);
> +
> + hu->priv = NULL;
> + kfree(nxp);
> +
> + return 0;
> +}
> +
> +/* Enqueue frame for transmission (padding, crc, etc) */ static int
> +nxp_enqueue(struct hci_uart *hu, struct sk_buff *skb) {
> + struct nxp_struct *nxp = hu->priv;
> + struct ps_data *psdata = nxp->psdata;
> + struct BT_CMD *pcmd = (struct BT_CMD *)skb->data;
> +
> + BT_DBG("hu %p skb %p", hu, skb);
> +
> + if (bt_cb(skb)->pkt_type == HCI_COMMAND_PKT) {
> + if (pcmd->ocf_ogf == ((OGF << 10) |
> BT_CMD_AUTO_SLEEP_MODE)) {
> + if (pcmd->data[0] == BT_PS_ENABLE)
> + psdata->ps_mode = PS_MODE_ENABLE;
> + else if (pcmd->data[0] == BT_PS_DISABLE)
> + psdata->ps_mode = PS_MODE_DISABLE;
> + }
> + if (pcmd->ocf_ogf == ((OGF << 10) |
> BT_CMD_WAKEUP_METHOD))
> + psdata->wakeupmode = pcmd->data[2];
> + }
BT_CMD_WAKEUP_METHOD data[2] value is BT_CTRL_WAKEUP_METHOD_*, the psdata->wakeupmode value is WAKEUP_METHOD_*, right?
Use "=" to direct assign the value may not appropriate here.
switch (cmd) {
case WAKEUP_METHOD_DTR:
pcmd->data[2] = BT_CTRL_WAKEUP_METHOD_DSR;
break;
case WAKEUP_METHOD_BREAK:
default:
pcmd->data[2] = BT_CTRL_WAKEUP_METHOD_BREAK;
break;
}
Best Regards
Sherry