Re: [EXT] Re: [PATCH v13 1/2] PCI: endpoint: pci-epf-vntb: change doorbell register offset calc mathod
From: Manivannan Sadhasivam
Date: Thu Nov 24 2022 - 13:51:31 EST
On Thu, Nov 24, 2022 at 05:49:32PM +0000, Frank Li wrote:
>
>
> > -----Original Message-----
> > From: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> > Sent: Thursday, November 24, 2022 3:19 AM
> > To: Frank Li <frank.li@xxxxxxx>
> > Cc: lpieralisi@xxxxxxxxxx; Aisheng Dong <aisheng.dong@xxxxxxx>;
> > bhelgaas@xxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; festevam@xxxxxxxxx;
> > imx@xxxxxxxxxxxxxxx; jdmason@xxxxxxxx; kernel@xxxxxxxxxxxxxx;
> > kishon@xxxxxx; krzysztof.kozlowski+dt@xxxxxxxxxx; kw@xxxxxxxxx; linux-
> > arm-kernel@xxxxxxxxxxxxxxxxxxx; dl-linux-imx <linux-imx@xxxxxxx>; linux-
> > kernel@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx;
> > lorenzo.pieralisi@xxxxxxx; lznuaa@xxxxxxxxx; maz@xxxxxxxxxx;
> > ntb@xxxxxxxxxxxxxxx; Peng Fan <peng.fan@xxxxxxx>; robh+dt@xxxxxxxxxx;
> > s.hauer@xxxxxxxxxxxxxx; shawnguo@xxxxxxxxxx; tglx@xxxxxxxxxxxxx
> > Subject: [EXT] Re: [PATCH v13 1/2] PCI: endpoint: pci-epf-vntb: change
> > doorbell register offset calc mathod
> >
> > Caution: EXT Email
> >
> > On Thu, Nov 24, 2022 at 12:50:35AM -0500, Frank Li wrote:
> > > In drivers/ntb/hw/epf/ntb_hw_epf.c
> > > ntb_epf_peer_db_set()
> > > {
> > > ...
> > > db_offset = readl(ndev->ctrl_reg + NTB_EPF_DB_OFFSET(interrupt_num));
> > > writel(db_data, ndev->db_reg + (db_entry_size * interrupt_num) +
> > > db_offset);
> > > ...
> > > }
> > >
> > > The door register offset's formular is
> > > offset = db_entry_size * interrupt_num + db_offset[interrupt_number]
> >
> > You did not mention the DB BAR here. Without that, this calculation doesn't
> > make sense.
>
> Doorbell register offset should means Base on DB BAR.
> How about "The formula of door register offset refer to DB BAR"?
"Doobell register offset in DB BAR is calculated using:"
>
> >
> > >
> > > Previous db_entry_size is 4, all db_offset is 0.
> >
> > s/Previous/Previously
> >
> > > irq | offset
> > > --------------
> > > 0 0
> > > 1 4
> > > 2 8
> > > ...
> > >
> > > Change to db_entry_size is 0 and db_offset is 0, 4, 8, ...
> > > So we can get the same map value between irq and offset. This will be
> > > convenience for hardware doorbell register memory map.
> > >
> >
> > In your irq-imx-mu-msi.c driver, the msi_address is calculated as:
> >
> > ```
> > u64 addr = msi_data->msiir_addr + 4 * data->hwirq;
> > ```
> >
> > So the MSI addresses itself are of 4 bytes width. So the offsets will be
> > separated by 8 bytes like, 0, 8, 16,... and this won't match the MSI addresses
> > as they are 4 bytes apart.
>
> Addr is absolute physical IO address, which increased by 4. But it doesn't matter.
> It should be okay if range is between 2^32.
>
> >
> > So you want to change the offset to 0, 4, 8,... by zeroing db_entry_size,
> > right?
>
> I want to directly using db_offset[irq] value as offset. It will be simple.
>
> I am not sure why ntb_hw_epf.c use below formular.
> "Db_offset[irq] + irq * db_entry_size"
>
> Db_entry_size = 0 will be simple, all offset will be controlled by db_offset[]
>
> You can save db_offset[] as 0, 4, 8... or 0, 8, 16 as needs.
>
> >
> > > Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
> > > ---
> > > drivers/pci/endpoint/functions/pci-epf-vntb.c | 4 ++--
> > > 1 file changed, 2 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/pci/endpoint/functions/pci-epf-vntb.c
> > b/drivers/pci/endpoint/functions/pci-epf-vntb.c
> > > index 04698e7995a5..0d744975f815 100644
> > > --- a/drivers/pci/endpoint/functions/pci-epf-vntb.c
> > > +++ b/drivers/pci/endpoint/functions/pci-epf-vntb.c
> > > @@ -461,11 +461,11 @@ static int epf_ntb_config_spad_bar_alloc(struct
> > epf_ntb *ntb)
> > > ctrl->num_mws = ntb->num_mws;
> > > ntb->spad_size = spad_size;
> > >
> > > - ctrl->db_entry_size = sizeof(u32);
> > > + ctrl->db_entry_size = 0;
> > >
> > > for (i = 0; i < ntb->db_count; i++) {
> > > ntb->reg->db_data[i] = 1 + i;
> > > - ntb->reg->db_offset[i] = 0;
> > > + ntb->reg->db_offset[i] = sizeof(u32) * i;
> >
> > If my above understanding is correct, then you could just reassign
> > "db_entry_size" in epf_ntb_epc_msi_init().
>
> Yes, that's one method.
> I want to use one method to calc db offset for both software polling
> and MSI. So overall logic should be simple.
>
I think it is better to leave db_entry_size for polling as it is and modify it
for MSI alone.
Thanks,
Mani
> Frank Li
>
> >
> > Thanks,
> > Mani
> >
> > > }
> > >
> > > return 0;
> > > --
> > > 2.34.1
> > >
> >
> > --
> > மணிவண்ணன் சதாசிவம்
--
மணிவண்ணன் சதாசிவம்