Re: [RFC PATCH v2 2/3] phy: qcom-qmp-combo: Add config for SM6350

[Johan Hovold]

On Fri, Nov 25, 2022 at 10:27:48AM +0100, Luca Weiss wrote:
> Add the tables and config for the combo phy found on SM6350.
> 
> Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
> ---
> @Johan Hovold, here I've added dp_txa & dp_txb, I believe otherwise
> qmp->dp_tx would be wrong. Is this different on sc8280xp or was this a
> mistake on your side? I think this should probably be split out to
> another patch to not mix things up too much.

Yeah, that's a difference in sc8280xp which does not have dedicated TX
registers for DP.

This is probably best handled explicitly when parsing the DT by using
dp_txa/b if they are set and otherwise fallback to txa/txb (e.g.
instead of hiding it in the v5 table by using the same offset in two
places).

It can be done as part of this patch as long as you mention it in the
commit message.

> I think other than that this patch is good.

Indeed, looks good! Nice to see this working out as intended also for
the older platforms.

>  static const struct qmp_phy_init_tbl sm8150_usb3_serdes_tbl[] = {
>  	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
>  	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
> @@ -809,6 +873,8 @@ struct qmp_combo_offsets {
>  	u16 usb3_pcs;
>  	u16 usb3_pcs_usb;
>  	u16 dp_serdes;
> +	u16 dp_txa;
> +	u16 dp_txb;
>  	u16 dp_dp_phy;
>  };
>  
> @@ -975,6 +1041,21 @@ static const char * const sc7180_usb3phy_reset_l[] = {
>  	"phy",
>  };
>  
> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = {
> +	.com		= 0x0000,
> +	.txa		= 0x1200,
> +	.rxa		= 0x1400,
> +	.txb		= 0x1600,
> +	.rxb		= 0x1800,
> +	.usb3_serdes	= 0x1000,
> +	.usb3_pcs_misc	= 0x1a00,
> +	.usb3_pcs	= 0x1c00,
> +	.dp_serdes	= 0x2000,
> +	.dp_txa		= 0x2200,
> +	.dp_txb		= 0x2600,
> +	.dp_dp_phy	= 0x2c00,
> +};
> +
>  static const struct qmp_combo_offsets qmp_combo_offsets_v5 = {
>  	.com		= 0x0000,
>  	.txa		= 0x0400,

> @@ -2641,8 +2767,8 @@ static int qmp_combo_parse_dt(struct qmp_combo *qmp)
>  	qmp->pcs_usb = base + offs->usb3_pcs_usb;
>  
>  	qmp->dp_serdes = base + offs->dp_serdes;
> -	qmp->dp_tx = base + offs->txa;
> -	qmp->dp_tx2 = base + offs->txb;
> +	qmp->dp_tx = base + offs->dp_txa;
> +	qmp->dp_tx2 = base + offs->dp_txb;
>  	qmp->dp_dp_phy = base + offs->dp_dp_phy;
>  
>  	qmp->pipe_clk = devm_clk_get(dev, "usb3_pipe");

Johan