[next v7 0/8] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on linux next from 2022/11/27.

i included sams series for mt7986 DTS with small changes
https://patchwork.kernel.org/project/linux-mediatek/cover/20220427124741.18245->

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined. These errors also came up for mt7986a-rfb.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v7:
- rebase on next so dropped already applied patches
- squashed overlay-patch into the bpi-r3 base support
- moved regulators from mmc-dts to common dtsi
- changed dtsi to dts (as board base dtb) and mmc-dts to overlays
- renamed overlays to dtso
- removed angelos RB because of changes in bpi-r3 patch

v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
  rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
  mails last 2 times while sending part 10)

v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays

Frank Wunderlich (5):
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  dt-bindings: usb: mtk-xhci: add support for mt7986
  dt-bindings: PCI: mediatek-gen3: add SoC based clock config
  dt-bindings: PCI: mediatek-gen3: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3

Sam Shih (3):
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/pci/mediatek-pcie-gen3.yaml      |  64 ++-
 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 .../bindings/usb/mediatek,mtk-xhci.yaml       |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  30 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 448 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
 12 files changed, 934 insertions(+), 12 deletions(-)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

-- 
2.34.1